Debian

In the Linux kernel, the following vulnerability has been resolved: serial: mxs-auart: add spinlock around changing cts state The uart_handle_cts_change() function in serial_core expects the caller to hold uport->lock. For example, I have seen the below kernel splat, when the Bluetooth driver is loaded on an i.MX28 board. [ 85.119255] ------------[ cut here ]------------ [ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec [ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs [ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1 [ 85.151396] Hardware name: Freescale MXS (Device Tree) [ 85.156679] Workqueue: hci0 hci_power_on [bluetooth] (...) [ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4 [ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210 (...)Show less

In the Linux kernel, the following vulnerability has been resolved: serial/pmac_zilog: Remove flawed mitigation for rx irq flood The mitigation was intended to stop the irq completely. That may be better than a hard lock-up but it turns out that you get a crash anyway if you're using pmac_zilog as a serial console: ttyPZ0: pmz: rx irq flood ! BUG: spinlock recursion on CPU#0, swapper/0 That's because the pr_err() call in pmz_receive_chars() results in pmz_console_write() attempting to lock a spinlock already locked in pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal BUG splat. The spinlock in question is the one in struct uart_port. Even when it's not fatal, the serial port rx function ceases to work. Also, the iteration limit doesn't play nicely with QEMU, as can be seen in the bug report linked below. A web search for other reports of the error message "pmz: rx irq flood" didn't produce anything. So I don't think this code is needed any more. Remove it.Show less

In the Linux kernel, the following vulnerability has been resolved: speakup: Avoid crash on very long word In case a console is set up really large and contains a really long word (> 256 characters), we have to stop before the length of the word buffer.Show less

In the Linux kernel, the following vulnerability has been resolved: init/main.c: Fix potential static_command_line memory overflow We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for static_command_line, but the strings copied into static_command_line are extra_command_line and command_line, rather than extra_command_line and boot_command_line. When strlen(command_line) > strlen(boot_command_line), static_command_line will overflow. This patch just recovers strlen(command_line) which was miss-consolidated with strlen(boot_command_line) in the commit f5c7310ac73e ("init/main: add checks for the return value of memblock_alloc*()")Show less

In the Linux kernel, the following vulnerability has been resolved: nouveau: fix instmem race condition around ptr stores Running a lot of VK CTS in parallel against nouveau, once every few hours you might see something like this crash. BUG: kernel NULL pointer dereference, address: 0000000000000008 PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27 Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021 RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1 RSP: 0000:ffffac20c5857838 EFLAGS: 00010202 RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001 RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180 RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10 R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ... ? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] ? gp100_vmm_pgt_mem+0x37/0x180 [nouveau] nvkm_vmm_iter+0x351/0xa20 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __lock_acquire+0x3ed/0x2170 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_map_locked+0x224/0x3a0 [nouveau] Adding any sort of useful debug usually makes it go away, so I hand wrote the function in a line, and debugged the asm. Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in the nv50_instobj_acquire called from nvkm_kmap. If Thread A and Thread B both get to nv50_instobj_acquire around the same time, and Thread A hits the refcount_set line, and in lockstep thread B succeeds at refcount_inc_not_zero, there is a chance the ptrs value won't have been stored since refcount_set is unordered. Force a memory barrier here, I picked smp_mb, since we want it on all CPUs and it's write followed by a read. v2: use paired smp_rmb/smp_wmb.Show less

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix OOB in nilfs_set_de_type The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function, which uses this array, specifies the index to read from the array in the same way as "(mode & S_IFMT) >> S_SHIFT". static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode *inode) { umode_t mode = inode->i_mode; de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob } However, when the index is determined this way, an out-of-bounds (OOB) error occurs by referring to an index that is 1 larger than the array size when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a patch to resize the nilfs_type_by_mode array should be applied to prevent OOB errors.Show less

In the Linux kernel, the following vulnerability has been resolved: KVM: Always flush async #PF workqueue when vCPU is being destroyed Always flush the per-vCPU async #PF workqueue when a vCPU is clearing its completion queue, e.g. when a VM and all its vCPUs is being destroyed. KVM must ensure that none of its workqueue callbacks is running when the last reference to the KVM _module_ is put. Gifting a reference to the associated VM prevents the workqueue callback from dereferencing freed vCPU/VM memory, but does not prevent the KVM module from being unloaded before the callback completes. Drop the misguided VM refcount gifting, as calling kvm_put_kvm() from async_pf_execute() if kvm_put_kvm() flushes the async #PF workqueue will result in deadlock. async_pf_execute() can't return until kvm_put_kvm() finishes, and kvm_put_kvm() can't return until async_pf_execute() finishes: WARNING: CPU: 8 PID: 251 at virt/kvm/kvm_main.c:1435 kvm_put_kvm+0x2d/0x320 [kvm] Modules linked in: vhost_net vhost vhost_iotlb tap kvm_intel kvm irqbypass CPU: 8 PID: 251 Comm: kworker/8:1 Tainted: G W 6.6.0-rc1-e7af8d17224a-x86/gmem-vm #119 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 Workqueue: events async_pf_execute [kvm] RIP: 0010:kvm_put_kvm+0x2d/0x320 [kvm] Call Trace: <TASK> async_pf_execute+0x198/0x260 [kvm] process_one_work+0x145/0x2d0 worker_thread+0x27e/0x3a0 kthread+0xba/0xe0 ret_from_fork+0x2d/0x50 ret_from_fork_asm+0x11/0x20 </TASK> ---[ end trace 0000000000000000 ]--- INFO: task kworker/8:1:251 blocked for more than 120 seconds. Tainted: G W 6.6.0-rc1-e7af8d17224a-x86/gmem-vm #119 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/8:1 state:D stack:0 pid:251 ppid:2 flags:0x00004000 Workqueue: events async_pf_execute [kvm] Call Trace: <TASK> __schedule+0x33f/0xa40 schedule+0x53/0xc0 schedule_timeout+0x12a/0x140 __wait_for_common+0x8d/0x1d0 __flush_work.isra.0+0x19f/0x2c0 kvm_clear_async_pf_completion_queue+0x129/0x190 [kvm] kvm_arch_destroy_vm+0x78/0x1b0 [kvm] kvm_put_kvm+0x1c1/0x320 [kvm] async_pf_execute+0x198/0x260 [kvm] process_one_work+0x145/0x2d0 worker_thread+0x27e/0x3a0 kthread+0xba/0xe0 ret_from_fork+0x2d/0x50 ret_from_fork_asm+0x11/0x20 </TASK> If kvm_clear_async_pf_completion_queue() actually flushes the workqueue, then there's no need to gift async_pf_execute() a reference because all invocations of async_pf_execute() will be forced to complete before the vCPU and its VM are destroyed/freed. And that in turn fixes the module unloading bug as __fput() won't do module_put() on the last vCPU reference until the vCPU has been freed, e.g. if closing the vCPU file also puts the last reference to the KVM module. Note that kvm_check_async_pf_completion() may also take the work item off the completion queue and so also needs to flush the work queue, as the work will not be seen by kvm_clear_async_pf_completion_queue(). Waiting on the workqueue could theoretically delay a vCPU due to waiting for the work to complete, but that's a very, very small chance, and likely a very small delay. kvm_arch_async_page_present_queued() unconditionally makes a new request, i.e. will effectively delay entering the guest, so the remaining work is really just: trace_kvm_async_pf_completed(addr, cr2_or_gpa); __kvm_vcpu_wake_up(vcpu); mmput(mm); and mmput() can't drop the last reference to the page tables if the vCPU is still alive, i.e. the vCPU won't get stuck tearing down page tables. Add a helper to do the flushing, specifically to deal with "wakeup all" work items, as they aren't actually work items, i.e. are never placed in a workqueue. Trying to flush a bogus workqueue entry rightly makes __flush_work() complain (kudos to whoever added that sanity check). Note, commit 5f6de5cbebee ("KVM: Prevent module exit until al ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - resolve race condition during AER recovery During the PCI AER system's error recovery process, the kernel driver may encounter a race condition with freeing the reset_data structure's memory. If the device restart will take more than 10 seconds the function scheduling that restart will exit due to a timeout, and the reset_data structure will be freed. However, this data structure is used for completion notification after the restart is completed, which leads to a UAF bug. This results in a KFENCE bug notice. BUG: KFENCE: use-after-free read in adf_device_reset_worker+0x38/0xa0 [intel_qat] Use-after-free read at 0x00000000bc56fddf (in kfence-#142): adf_device_reset_worker+0x38/0xa0 [intel_qat] process_one_work+0x173/0x340 To resolve this race condition, the memory associated to the container of the work_struct is freed on the worker if the timeout expired, otherwise on the function that schedules the worker. The timeout detection can be done by checking if the caller is still waiting for completion or not by using completion_done() function.Show less

In the Linux kernel, the following vulnerability has been resolved: fat: fix uninitialized field in nostale filehandles When fat_encode_fh_nostale() encodes file handle without a parent it stores only first 10 bytes of the file handle. However the length of the file handle must be a multiple of 4 so the file handle is actually 12 bytes long and the last two bytes remain uninitialized. This is not great at we potentially leak uninitialized information with the handle to userspace. Properly initialize the full handle length.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.Show less

In the Linux kernel, the following vulnerability has been resolved: mm: swap: fix race between free_swap_and_cache() and swapoff() There was previously a theoretical window where swapoff() could run and teardown a swap_info_struct while a call to free_swap_and_cache() was running in another thread. This could cause, amongst other bad possibilities, swap_page_trans_huge_swapped() (called by free_swap_and_cache()) to access the freed memory for swap_map. This is a theoretical problem and I haven't been able to provoke it from a test case. But there has been agreement based on code review that this is possible (see link below). Fix it by using get_swap_device()/put_swap_device(), which will stall swapoff(). There was an extra check in _swap_info_get() to confirm that the swap entry was not free. This isn't present in get_swap_device() because it doesn't make sense in general due to the race between getting the reference and swapoff. So I've added an equivalent check directly in free_swap_and_cache(). Details of how to provoke one possible issue (thanks to David Hildenbrand for deriving this): --8<----- __swap_entry_free() might be the last user and result in "count == SWAP_HAS_CACHE". swapoff->try_to_unuse() will stop as soon as soon as si->inuse_pages==0. So the question is: could someone reclaim the folio and turn si->inuse_pages==0, before we completed swap_page_trans_huge_swapped(). Imagine the following: 2 MiB folio in the swapcache. Only 2 subpages are still references by swap entries. Process 1 still references subpage 0 via swap entry. Process 2 still references subpage 1 via swap entry. Process 1 quits. Calls free_swap_and_cache(). -> count == SWAP_HAS_CACHE [then, preempted in the hypervisor etc.] Process 2 quits. Calls free_swap_and_cache(). -> count == SWAP_HAS_CACHE Process 2 goes ahead, passes swap_page_trans_huge_swapped(), and calls __try_to_reclaim_swap(). __try_to_reclaim_swap()->folio_free_swap()->delete_from_swap_cache()-> put_swap_folio()->free_swap_slot()->swapcache_free_entries()-> swap_entry_free()->swap_range_free()-> ... WRITE_ONCE(si->inuse_pages, si->inuse_pages - nr_entries); What stops swapoff to succeed after process 2 reclaimed the swap cache but before process1 finished its call to swap_page_trans_huge_swapped()? --8<-----Show less

In the Linux kernel, the following vulnerability has been resolved: nfs: fix UAF in direct writes In production we have been hitting the following warning consistently ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 17 PID: 1800359 at lib/refcount.c:28 refcount_warn_saturate+0x9c/0xe0 Workqueue: nfsiod nfs_direct_write_schedule_work [nfs] RIP: 0010:refcount_warn_saturate+0x9c/0xe0 PKRU: 55555554 Call Trace: <TASK> ? __warn+0x9f/0x130 ? refcount_warn_saturate+0x9c/0xe0 ? report_bug+0xcc/0x150 ? handle_bug+0x3d/0x70 ? exc_invalid_op+0x16/0x40 ? asm_exc_invalid_op+0x16/0x20 ? refcount_warn_saturate+0x9c/0xe0 nfs_direct_write_schedule_work+0x237/0x250 [nfs] process_one_work+0x12f/0x4a0 worker_thread+0x14e/0x3b0 ? ZSTD_getCParams_internal+0x220/0x220 kthread+0xdc/0x120 ? __btf_name_valid+0xa0/0xa0 ret_from_fork+0x1f/0x30 This is because we're completing the nfs_direct_request twice in a row. The source of this is when we have our commit requests to submit, we process them and send them off, and then in the completion path for the commit requests we have if (nfs_commit_end(cinfo.mds)) nfs_direct_write_complete(dreq); However since we're submitting asynchronous requests we sometimes have one that completes before we submit the next one, so we end up calling complete on the nfs_direct_request twice. The only other place we use nfs_generic_commit_list() is in __nfs_commit_inode, which wraps this call in a nfs_commit_begin(); nfs_commit_end(); Which is a common pattern for this style of completion handling, one that is also repeated in the direct code with get_dreq()/put_dreq() calls around where we process events as well as in the completion paths. Fix this by using the same pattern for the commit requests. Before with my 200 node rocksdb stress running this warning would pop every 10ish minutes. With my patch the stress test has been running for several hours without popping.Show less

In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: fix reference counting on zcrypt card objects Tests with hot-plugging crytpo cards on KVM guests with debug kernel build revealed an use after free for the load field of the struct zcrypt_card. The reason was an incorrect reference handling of the zcrypt card object which could lead to a free of the zcrypt card object while it was still in use. This is an example of the slab message: kernel: 0x00000000885a7512-0x00000000885a7513 @offset=1298. First byte 0x68 instead of 0x6b kernel: Allocated in zcrypt_card_alloc+0x36/0x70 [zcrypt] age=18046 cpu=3 pid=43 kernel: kmalloc_trace+0x3f2/0x470 kernel: zcrypt_card_alloc+0x36/0x70 [zcrypt] kernel: zcrypt_cex4_card_probe+0x26/0x380 [zcrypt_cex4] kernel: ap_device_probe+0x15c/0x290 kernel: really_probe+0xd2/0x468 kernel: driver_probe_device+0x40/0xf0 kernel: __device_attach_driver+0xc0/0x140 kernel: bus_for_each_drv+0x8c/0xd0 kernel: __device_attach+0x114/0x198 kernel: bus_probe_device+0xb4/0xc8 kernel: device_add+0x4d2/0x6e0 kernel: ap_scan_adapter+0x3d0/0x7c0 kernel: ap_scan_bus+0x5a/0x3b0 kernel: ap_scan_bus_wq_callback+0x40/0x60 kernel: process_one_work+0x26e/0x620 kernel: worker_thread+0x21c/0x440 kernel: Freed in zcrypt_card_put+0x54/0x80 [zcrypt] age=9024 cpu=3 pid=43 kernel: kfree+0x37e/0x418 kernel: zcrypt_card_put+0x54/0x80 [zcrypt] kernel: ap_device_remove+0x4c/0xe0 kernel: device_release_driver_internal+0x1c4/0x270 kernel: bus_remove_device+0x100/0x188 kernel: device_del+0x164/0x3c0 kernel: device_unregister+0x30/0x90 kernel: ap_scan_adapter+0xc8/0x7c0 kernel: ap_scan_bus+0x5a/0x3b0 kernel: ap_scan_bus_wq_callback+0x40/0x60 kernel: process_one_work+0x26e/0x620 kernel: worker_thread+0x21c/0x440 kernel: kthread+0x150/0x168 kernel: __ret_from_fork+0x3c/0x58 kernel: ret_from_fork+0xa/0x30 kernel: Slab 0x00000372022169c0 objects=20 used=18 fp=0x00000000885a7c88 flags=0x3ffff00000000a00(workingset|slab|node=0|zone=1|lastcpupid=0x1ffff) kernel: Object 0x00000000885a74b8 @offset=1208 fp=0x00000000885a7c88 kernel: Redzone 00000000885a74b0: bb bb bb bb bb bb bb bb ........ kernel: Object 00000000885a74b8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk kernel: Object 00000000885a74c8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk kernel: Object 00000000885a74d8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk kernel: Object 00000000885a74e8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk kernel: Object 00000000885a74f8: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk kernel: Object 00000000885a7508: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 68 4b 6b 6b 6b a5 kkkkkkkkkkhKkkk. kernel: Redzone 00000000885a7518: bb bb bb bb bb bb bb bb ........ kernel: Padding 00000000885a756c: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZ kernel: CPU: 0 PID: 387 Comm: systemd-udevd Not tainted 6.8.0-HF #2 kernel: Hardware name: IBM 3931 A01 704 (KVM/Linux) kernel: Call Trace: kernel: [<00000000ca5ab5b8>] dump_stack_lvl+0x90/0x120 kernel: [<00000000c99d78bc>] check_bytes_and_report+0x114/0x140 kernel: [<00000000c99d53cc>] check_object+0x334/0x3f8 kernel: [<00000000c99d820c>] alloc_debug_processing+0xc4/0x1f8 kernel: [<00000000c99d852e>] get_partial_node.part.0+0x1ee/0x3e0 kernel: [<00000000c99d94ec>] ___slab_alloc+0xaf4/0x13c8 kernel: [<00000000c99d9e38>] __slab_alloc.constprop.0+0x78/0xb8 kernel: [<00000000c99dc8dc>] __kmalloc+0x434/0x590 kernel: [<00000000c9b4c0ce>] ext4_htree_store_dirent+0x4e/0x1c0 kernel: [<00000000c9b908a2>] htree_dirblock_to_tree+0x17a/0x3f0 kernel: ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix failure to detect DAT corruption in btree and direct mappings Patch series "nilfs2: fix kernel bug at submit_bh_wbc()". This resolves a kernel BUG reported by syzbot. Since there are two flaws involved, I've made each one a separate patch. The first patch alone resolves the syzbot-reported bug, but I think both fixes should be sent to stable, so I've tagged them as such. This patch (of 2): Syzbot has reported a kernel bug in submit_bh_wbc() when writing file data to a nilfs2 file system whose metadata is corrupted. There are two flaws involved in this issue. The first flaw is that when nilfs_get_block() locates a data block using btree or direct mapping, if the disk address translation routine nilfs_dat_translate() fails with internal code -ENOENT due to DAT metadata corruption, it can be passed back to nilfs_get_block(). This causes nilfs_get_block() to misidentify an existing block as non-existent, causing both data block lookup and insertion to fail inconsistently. The second flaw is that nilfs_get_block() returns a successful status in this inconsistent state. This causes the caller __block_write_begin_int() or others to request a read even though the buffer is not mapped, resulting in a BUG_ON check for the BH_Mapped flag in submit_bh_wbc() failing. This fixes the first issue by changing the return value to code -EINVAL when a conversion using DAT fails with code -ENOENT, avoiding the conflicting condition that leads to the kernel bug described above. Here, code -EINVAL indicates that metadata corruption was detected during the block lookup, which will be properly handled as a file system error and converted to -EIO when passing through the nilfs2 bmap layer.Show less

In the Linux kernel, the following vulnerability has been resolved: nilfs2: prevent kernel bug at submit_bh_wbc() Fix a bug where nilfs_get_block() returns a successful status when searching and inserting the specified block both fail inconsistently. If this inconsistent behavior is not due to a previously fixed bug, then an unexpected race is occurring, so return a temporary error -EAGAIN instead. This prevents callers such as __block_write_begin_int() from requesting a read into a buffer that is not mapped, which would cause the BUG_ON check for the BH_Mapped flag in submit_bh_wbc() to fail.Show less

In the Linux kernel, the following vulnerability has been resolved: wireguard: netlink: check for dangling peer via is_dead instead of empty list If all peers are removed via wg_peer_remove_all(), rather than setting peer_list to empty, the peer is added to a temporary list with a head on the stack of wg_peer_remove_all(). If a netlink dump is resumed and the cursored peer is one that has been removed via wg_peer_remove_all(), it will iterate from that peer and then attempt to dump freed peers. Fix this by instead checking peer->is_dead, which was explictly created for this purpose. Also move up the device_update_lock lockdep assertion, since reading is_dead relies on that. It can be reproduced by a small script like: echo "Setting config..." ip link add dev wg0 type wireguard wg setconf wg0 /big-config ( while true; do echo "Showing config..." wg showconf wg0 > /dev/null done ) & sleep 4 wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n") Resulting in: BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20 Read of size 8 at addr ffff88811956ec70 by task wg/59 CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5 Call Trace: <TASK> dump_stack_lvl+0x47/0x70 print_address_description.constprop.0+0x2c/0x380 print_report+0xab/0x250 kasan_report+0xba/0xf0 __lock_acquire+0x182a/0x1b20 lock_acquire+0x191/0x4b0 down_read+0x80/0x440 get_peer+0x140/0xcb0 wg_get_device_dump+0x471/0x1130Show less