Linux

In the Linux kernel, the following vulnerability has been resolved: xhci: Fix command ring pointer corruption while aborting a command The command ring pointer is located at [6:63] bits of the command ring control register (CRCR). All the control bits like command stop, abort are located at [0:3] bits. While aborting a command, we read the CRCR and set the abort bit and write to the CRCR. The read will always give command ring pointer as all zeros. So we essentially write only the control bits. Since we split the 64 bit write into two 32 bit writes, there is a possibility of xHC command ring stopped before the upper dword (all zeros) is written. If that happens, xHC updates the upper dword of its internal command ring pointer with all zeros. Next time, when the command ring is restarted, we see xHC memory access failures. Fix this issue by only writing to the lower dword of CRCR where all control bits are located.Show less

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix abort logic in btrfs_replace_file_extents Error injection testing uncovered a case where we'd end up with a corrupt file system with a missing extent in the middle of a file. This occurs because the if statement to decide if we should abort is wrong. The only way we would abort in this case is if we got a ret != -EOPNOTSUPP and we called from the file clone code. However the prealloc code uses this path too. Instead we need to abort if there is an error, and the only error we _don't_ abort on is -EOPNOTSUPP and only if we came from the clone file code.Show less

In the Linux kernel, the following vulnerability has been resolved: tracing: Have trace_event_file have ref counters The following can crash the kernel: # cd /sys/kernel/tracing # echo 'p:sched schedule' > kprobe_events # exec 5>>events/kprobes/sched/enable # > kprobe_events # exec 5>&- The above commands: 1. Change directory to the tracefs directory 2. Create a kprobe event (doesn't matter what one) 3. Open bash file descriptor 5 on the enable file of the kprobe event 4. Delete the kprobe event (removes the files too) 5. Close the bash file descriptor 5 The above causes a crash! BUG: kernel NULL pointer dereference, address: 0000000000000028 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 6 PID: 877 Comm: bash Not tainted 6.5.0-rc4-test-00008-g2c6b6b1029d4-dirty #186 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:tracing_release_file_tr+0xc/0x50 What happens here is that the kprobe event creates a trace_event_file "file" descriptor that represents the file in tracefs to the event. It maintains state of the event (is it enabled for the given instance?). Opening the "enable" file gets a reference to the event "file" descriptor via the open file descriptor. When the kprobe event is deleted, the file is also deleted from the tracefs system which also frees the event "file" descriptor. But as the tracefs file is still opened by user space, it will not be totally removed until the final dput() is called on it. But this is not true with the event "file" descriptor that is already freed. If the user does a write to or simply closes the file descriptor it will reference the event "file" descriptor that was just freed, causing a use-after-free bug. To solve this, add a ref count to the event "file" descriptor as well as a new flag called "FREED". The "file" will not be freed until the last reference is released. But the FREE flag will be set when the event is removed to prevent any more modifications to that event from happening, even if there's still a reference to the event "file" descriptor.Show less

In the Linux kernel, the following vulnerability has been resolved: can: dev: can_put_echo_skb(): don't crash kernel if can_priv::echo_skb is accessed out of bounds If the "struct can_priv::echoo_skb" is accessed out of bounds, this would cause a kernel crash. Instead, issue a meaningful warning message and return with an error.Show less

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm() It is possible that typec_register_partner() returns ERR_PTR on failure. When port->partner is an error, a NULL pointer dereference may occur as shown below. [91222.095236][ T319] typec port0: failed to register partner (-17) ... [91225.061491][ T319] Unable to handle kernel NULL pointer dereference at virtual address 000000000000039f [91225.274642][ T319] pc : tcpm_pd_data_request+0x310/0x13fc [91225.274646][ T319] lr : tcpm_pd_data_request+0x298/0x13fc [91225.308067][ T319] Call trace: [91225.308070][ T319] tcpm_pd_data_request+0x310/0x13fc [91225.308073][ T319] tcpm_pd_rx_handler+0x100/0x9e8 [91225.355900][ T319] kthread_worker_fn+0x178/0x58c [91225.355902][ T319] kthread+0x150/0x200 [91225.355905][ T319] ret_from_fork+0x10/0x30 Add a check for port->partner to avoid dereferencing a NULL pointer.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt7629-eth: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt2701: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: x86/tdx: Zero out the missing RSI in TDX_HYPERCALL macro In the TDX_HYPERCALL asm, after the TDCALL instruction returns from the untrusted VMM, the registers that the TDX guest shares to the VMM need to be cleared to avoid speculative execution of VMM-provided values. RSI is specified in the bitmap of those registers, but it is missing when zeroing out those registers in the current TDX_HYPERCALL. It was there when it was originally added in commit 752d13305c78 ("x86/tdx: Expand __tdx_hypercall() to handle more arguments"), but was later removed in commit 1e70c680375a ("x86/tdx: Do not corrupt frame-pointer in __tdx_hypercall()"), which was correct because %rsi is later restored in the "pop %rsi". However a later commit 7a3a401874be ("x86/tdx: Drop flags from __tdx_hypercall()") removed that "pop %rsi" but forgot to add the "xor %rsi, %rsi" back. Fix by adding it back.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt6779: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: tty: n_gsm: fix race condition in status line change on dead connections gsm_cleanup_mux() cleans up the gsm by closing all DLCIs, stopping all timers, removing the virtual tty devices and clearing the data queues. This procedure, however, may cause subsequent changes of the virtual modem status lines of a DLCI. More data is being added the outgoing data queue and the deleted kick timer is restarted to handle this. At this point many resources have already been removed by the cleanup procedure. Thus, a kernel panic occurs. Fix this by proving in gsm_modem_update() that the cleanup procedure has not been started and the mux is still alive. Note that writing to a virtual tty is already protected by checks against the DLCI specific connection state.Show less

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: llcc: Handle a second device without data corruption Usually there is only one llcc device. But if there were a second, even a failed probe call would modify the global drv_data pointer. So check if drv_data is valid before overwriting it.Show less

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt6765: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: pstore/platform: Add check for kstrdup Add check for the return value of kstrdup() and return the error if it fails in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: thermal: core: prevent potential string overflow The dev->id value comes from ida_alloc() so it's a number between zero and INT_MAX. If it's too high then these sprintf()s will overflow.Show less

In the Linux kernel, the following vulnerability has been resolved: HID: uclogic: Fix user-memory-access bug in uclogic_params_ugee_v2_init_event_hooks() When CONFIG_HID_UCLOGIC=y and CONFIG_KUNIT_ALL_TESTS=y, launch kernel and then the below user-memory-access bug occurs. In hid_test_uclogic_params_cleanup_event_hooks(),it call uclogic_params_ugee_v2_init_event_hooks() with the first arg=NULL, so when it calls uclogic_params_ugee_v2_has_battery(), the hid_get_drvdata() will access hdev->dev with hdev=NULL, which will cause below user-memory-access. So add a fake_device with quirks member and call hid_set_drvdata() to assign hdev->dev->driver_data which avoids the null-ptr-def bug for drvdata->quirks in uclogic_params_ugee_v2_has_battery(). After applying this patch, the below user-memory-access bug never occurs. general protection fault, probably for non-canonical address 0xdffffc0000000329: 0000 [#1] PREEMPT SMP KASAN KASAN: probably user-memory-access in range [0x0000000000001948-0x000000000000194f] CPU: 5 PID: 2189 Comm: kunit_try_catch Tainted: G B W N 6.6.0-rc2+ #30 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ffffffff8fdd6cf5 DR2: ffffffff8fdd6cf6 DR3: ffffffff8fdd6cf7 DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 ? sched_clock_cpu+0x69/0x550 ? uclogic_parse_ugee_v2_desc_gen_params+0x70/0x70 ? load_balance+0x2950/0x2950 ? rcu_trc_cmpxchg_need_qs+0x67/0xa0 hid_test_uclogic_params_cleanup_event_hooks+0x9e/0x1a0 ? uclogic_params_ugee_v2_init_event_hooks+0x600/0x600 ? __switch_to+0x5cf/0xe60 ? migrate_enable+0x260/0x260 ? __kthread_parkme+0x83/0x150 ? kunit_try_run_case_cleanup+0xe0/0xe0 kunit_generic_run_threadfn_adapter+0x4a/0x90 ? kunit_try_catch_throw+0x80/0x80 kthread+0x2b5/0x380 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x2d/0x70 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork_asm+0x11/0x20 </TASK> Modules linked in: Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 0000000000000000 ]--- RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: clk-mt6797: Add check for mtk_alloc_clk_data Add the check for the return value of mtk_alloc_clk_data() in order to avoid NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: platform/x86: wmi: Fix opening of char device Since commit fa1f68db6ca7 ("drivers: misc: pass miscdevice pointer via file private data"), the miscdevice stores a pointer to itself inside filp->private_data, which means that private_data will not be NULL when wmi_char_open() is called. This might cause memory corruption should wmi_char_open() be unable to find its driver, something which can happen when the associated WMI device is deleted in wmi_free_devices(). Fix the problem by using the miscdevice pointer to retrieve the WMI device data associated with a char device using container_of(). This also avoids wmi_char_open() picking a wrong WMI device bound to a driver with the same name as the original driver.Show less

In the Linux kernel, the following vulnerability has been resolved: hwmon: (axi-fan-control) Fix possible NULL pointer dereference axi_fan_control_irq_handler(), dependent on the private axi_fan_control_data structure, might be called before the hwmon device is registered. That will cause an "Unable to handle kernel NULL pointer dereference" error.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix null pointer dereference in error message This patch fixes a null pointer dereference in the error message that is printed when the Display Core (DC) fails to initialize. The original message includes the DC version number, which is undefined if the DC is not initialized.Show less