Linux

In the Linux kernel, the following vulnerability has been resolved: audit: don't deref the syscall args when checking the openat2 open_how::flags As reported by Jeff, dereferencing the openat2 syscall argument in audit_match_perm() to obtain the open_how::flags can result in an oops/page-fault. This patch fixes this by using the open_how struct that we store in the audit_context with audit_openat2_how(). Independent of this patch, Richard Guy Briggs posted a similar patch to the audit mailing list roughly 40 minutes after this patch was posted.Show less

In the Linux kernel, the following vulnerability has been resolved: can: isotp: fix potential CAN frame reception race in isotp_rcv() When receiving a CAN frame the current code logic does not consider concurrently receiving processes which do not show up in real world usage. Ziyang Xuan writes: The following syz problem is one of the scenarios. so->rx.len is changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals 0 before alloc_skb() and equals 4096 after alloc_skb(). That will trigger skb_over_panic() in skb_put(). ======================================================= CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0 RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113 Call Trace: <TASK> skb_over_panic net/core/skbuff.c:118 [inline] skb_put.cold+0x24/0x24 net/core/skbuff.c:1990 isotp_rcv_cf net/can/isotp.c:570 [inline] isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668 deliver net/can/af_can.c:574 [inline] can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635 can_receive+0x31d/0x580 net/can/af_can.c:665 can_rcv+0x120/0x1c0 net/can/af_can.c:696 __netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465 __netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579 Therefore we make sure the state changes and data structures stay consistent at CAN frame reception time by adding a spin_lock in isotp_rcv(). This fixes the issue reported by syzkaller but does not affect real world operation.Show less

In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes iattr::ia_size is a loff_t, so these NFSv3 procedures must be careful to deal with incoming client size values that are larger than s64_max without corrupting the value. Silently capping the value results in storing a different value than the client passed in which is unexpected behavior, so remove the min_t() check in decode_sattr3(). Note that RFC 1813 permits only the WRITE procedure to return NFS3ERR_FBIG. We believe that NFSv3 reference implementations also return NFS3ERR_FBIG when ia_size is too large.Show less

In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix ia_size underflow iattr::ia_size is a loff_t, which is a signed 64-bit type. NFSv3 and NFSv4 both define file size as an unsigned 64-bit type. Thus there is a range of valid file size values an NFS client can send that is already larger than Linux can handle. Currently decode_fattr4() dumps a full u64 value into ia_size. If that value happens to be larger than S64_MAX, then ia_size underflows. I'm about to fix up the NFSv3 behavior as well, so let's catch the underflow in the common code path: nfsd_setattr().Show less

In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix the behavior of READ near OFFSET_MAX Dan Aloni reports: > Due to commit 8cfb9015280d ("NFS: Always provide aligned buffers to > the RPC read layers") on the client, a read of 0xfff is aligned up > to server rsize of 0x1000. > > As a result, in a test where the server has a file of size > 0x7fffffffffffffff, and the client tries to read from the offset > 0x7ffffffffffff000, the read causes loff_t overflow in the server > and it returns an NFS code of EINVAL to the client. The client as > a result indefinitely retries the request. The Linux NFS client does not handle NFS?ERR_INVAL, even though all NFS specifications permit servers to return that status code for a READ. Instead of NFS?ERR_INVAL, have out-of-range READ requests succeed and return a short result. Set the EOF flag in the result to prevent the client from retrying the READ request. This behavior appears to be consistent with Solaris NFS servers. Note that NFSv3 and NFSv4 use u64 offset values on the wire. These must be converted to loff_t internally before use -- an implicit type cast is not adequate for this purpose. Otherwise VFS checks against sb->s_maxbytes do not work properly.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: Fix deadlock on DSI device attach error DSI device attach to DSI host will be done with host device's lock held. Un-registering host in "device attach" error path (ex: probe retry) will result in deadlock with below call trace and non operational DSI display. Startup Call trace: [ 35.043036] rt_mutex_slowlock.constprop.21+0x184/0x1b8 [ 35.043048] mutex_lock_nested+0x7c/0xc8 [ 35.043060] device_del+0x4c/0x3e8 [ 35.043075] device_unregister+0x20/0x40 [ 35.043082] mipi_dsi_remove_device_fn+0x18/0x28 [ 35.043093] device_for_each_child+0x68/0xb0 [ 35.043105] mipi_dsi_host_unregister+0x40/0x90 [ 35.043115] vc4_dsi_host_attach+0xf0/0x120 [vc4] [ 35.043199] mipi_dsi_attach+0x30/0x48 [ 35.043209] tc358762_probe+0x128/0x164 [tc358762] [ 35.043225] mipi_dsi_drv_probe+0x28/0x38 [ 35.043234] really_probe+0xc0/0x318 [ 35.043244] __driver_probe_device+0x80/0xe8 [ 35.043254] driver_probe_device+0xb8/0x118 [ 35.043263] __device_attach_driver+0x98/0xe8 [ 35.043273] bus_for_each_drv+0x84/0xd8 [ 35.043281] __device_attach+0xf0/0x150 [ 35.043290] device_initial_probe+0x1c/0x28 [ 35.043300] bus_probe_device+0xa4/0xb0 [ 35.043308] deferred_probe_work_func+0xa0/0xe0 [ 35.043318] process_one_work+0x254/0x700 [ 35.043330] worker_thread+0x4c/0x448 [ 35.043339] kthread+0x19c/0x1a8 [ 35.043348] ret_from_fork+0x10/0x20 Shutdown Call trace: [ 365.565417] Call trace: [ 365.565423] __switch_to+0x148/0x200 [ 365.565452] __schedule+0x340/0x9c8 [ 365.565467] schedule+0x48/0x110 [ 365.565479] schedule_timeout+0x3b0/0x448 [ 365.565496] wait_for_completion+0xac/0x138 [ 365.565509] __flush_work+0x218/0x4e0 [ 365.565523] flush_work+0x1c/0x28 [ 365.565536] wait_for_device_probe+0x68/0x158 [ 365.565550] device_shutdown+0x24/0x348 [ 365.565561] kernel_restart_prepare+0x40/0x50 [ 365.565578] kernel_restart+0x20/0x70 [ 365.565591] __do_sys_reboot+0x10c/0x220 [ 365.565605] __arm64_sys_reboot+0x2c/0x38 [ 365.565619] invoke_syscall+0x4c/0x110 [ 365.565634] el0_svc_common.constprop.3+0xfc/0x120 [ 365.565648] do_el0_svc+0x2c/0x90 [ 365.565661] el0_svc+0x4c/0xf0 [ 365.565671] el0t_64_sync_handler+0x90/0xb8 [ 365.565682] el0t_64_sync+0x180/0x184Show less

In the Linux kernel, the following vulnerability has been resolved: scsi: qedf: Add stag_work to all the vports Call trace seen when creating NPIV ports, only 32 out of 64 show online. stag work was not initialized for vport, hence initialize the stag work. WARNING: CPU: 8 PID: 645 at kernel/workqueue.c:1635 __queue_delayed_work+0x68/0x80 CPU: 8 PID: 645 Comm: kworker/8:1 Kdump: loaded Tainted: G IOE --------- -- 4.18.0-348.el8.x86_64 #1 Hardware name: Dell Inc. PowerEdge MX740c/0177V9, BIOS 2.12.2 07/09/2021 Workqueue: events fc_lport_timeout [libfc] RIP: 0010:__queue_delayed_work+0x68/0x80 Code: 89 b2 88 00 00 00 44 89 82 90 00 00 00 48 01 c8 48 89 42 50 41 81 f8 00 20 00 00 75 1d e9 60 24 07 00 44 89 c7 e9 98 f6 ff ff <0f> 0b eb c5 0f 0b eb a1 0f 0b eb a7 0f 0b eb ac 44 89 c6 e9 40 23 RSP: 0018:ffffae514bc3be40 EFLAGS: 00010006 RAX: ffff8d25d6143750 RBX: 0000000000000202 RCX: 0000000000000002 RDX: ffff8d2e31383748 RSI: ffff8d25c000d600 RDI: ffff8d2e31383788 RBP: ffff8d2e31380de0 R08: 0000000000002000 R09: ffff8d2e31383750 R10: ffffffffc0c957e0 R11: ffff8d2624800000 R12: ffff8d2e31380a58 R13: ffff8d2d915eb000 R14: ffff8d25c499b5c0 R15: ffff8d2e31380e18 FS: 0000000000000000(0000) GS:ffff8d2d1fb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055fd0484b8b8 CR3: 00000008ffc10006 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: queue_delayed_work_on+0x36/0x40 qedf_elsct_send+0x57/0x60 [qedf] fc_lport_enter_flogi+0x90/0xc0 [libfc] fc_lport_timeout+0xb7/0x140 [libfc] process_one_work+0x1a7/0x360 ? create_worker+0x1a0/0x1a0 worker_thread+0x30/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x116/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x35/0x40 ---[ end trace 008f00f722f2c2ff ]-- Initialize stag work for all the vports.Show less

In the Linux kernel, the following vulnerability has been resolved: scsi: myrs: Fix crash in error case In myrs_detect(), cs->disable_intr is NULL when privdata->hw_init() fails with non-zero. In this case, myrs_cleanup(cs) will call a NULL ptr and crash the kernel. [ 1.105606] myrs 0000:00:03.0: Unknown Initialization Error 5A [ 1.105872] myrs 0000:00:03.0: Failed to initialize Controller [ 1.106082] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 1.110774] Call Trace: [ 1.110950] myrs_cleanup+0xe4/0x150 [myrs] [ 1.111135] myrs_probe.cold+0x91/0x56a [myrs] [ 1.111302] ? DAC960_GEM_intr_handler+0x1f0/0x1f0 [myrs] [ 1.111500] local_pci_probe+0x48/0x90Show less

In the Linux kernel, the following vulnerability has been resolved: scsi: qedf: Fix refcount issue when LOGO is received during TMF Hung task call trace was seen during LOGO processing. [ 974.309060] [0000:00:00.0]:[qedf_eh_device_reset:868]: 1:0:2:0: LUN RESET Issued... [ 974.309065] [0000:00:00.0]:[qedf_initiate_tmf:2422]: tm_flags 0x10 sc_cmd 00000000c16b930f op = 0x2a target_id = 0x2 lun=0 [ 974.309178] [0000:00:00.0]:[qedf_initiate_tmf:2431]: portid=016900 tm_flags =LUN RESET [ 974.309222] [0000:00:00.0]:[qedf_initiate_tmf:2438]: orig io_req = 00000000ec78df8f xid = 0x180 ref_cnt = 1. [ 974.309625] host1: rport 016900: Received LOGO request while in state Ready [ 974.309627] host1: rport 016900: Delete port [ 974.309642] host1: rport 016900: work event 3 [ 974.309644] host1: rport 016900: lld callback ev 3 [ 974.313243] [0000:61:00.2]:[qedf_execute_tmf:2383]:1: fcport is uploading, not executing flush. [ 974.313295] [0000:61:00.2]:[qedf_execute_tmf:2400]:1: task mgmt command success... [ 984.031088] INFO: task jbd2/dm-15-8:7645 blocked for more than 120 seconds. [ 984.031136] Not tainted 4.18.0-305.el8.x86_64 #1 [ 984.031166] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 984.031209] jbd2/dm-15-8 D 0 7645 2 0x80004080 [ 984.031212] Call Trace: [ 984.031222] __schedule+0x2c4/0x700 [ 984.031230] ? unfreeze_partials.isra.83+0x16e/0x1a0 [ 984.031233] ? bit_wait_timeout+0x90/0x90 [ 984.031235] schedule+0x38/0xa0 [ 984.031238] io_schedule+0x12/0x40 [ 984.031240] bit_wait_io+0xd/0x50 [ 984.031243] __wait_on_bit+0x6c/0x80 [ 984.031248] ? free_buffer_head+0x21/0x50 [ 984.031251] out_of_line_wait_on_bit+0x91/0xb0 [ 984.031257] ? init_wait_var_entry+0x50/0x50 [ 984.031268] jbd2_journal_commit_transaction+0x112e/0x19f0 [jbd2] [ 984.031280] kjournald2+0xbd/0x270 [jbd2] [ 984.031284] ? finish_wait+0x80/0x80 [ 984.031291] ? commit_timeout+0x10/0x10 [jbd2] [ 984.031294] kthread+0x116/0x130 [ 984.031300] ? kthread_flush_work_fn+0x10/0x10 [ 984.031305] ret_from_fork+0x1f/0x40 There was a ref count issue when LOGO is received during TMF. This leads to one of the I/Os hanging with the driver. Fix the ref count.Show less

In the Linux kernel, the following vulnerability has been resolved: usb: f_fs: Fix use-after-free for epfile Consider a case where ffs_func_eps_disable is called from ffs_func_disable as part of composition switch and at the same time ffs_epfile_release get called from userspace. ffs_epfile_release will free up the read buffer and call ffs_data_closed which in turn destroys ffs->epfiles and mark it as NULL. While this was happening the driver has already initialized the local epfile in ffs_func_eps_disable which is now freed and waiting to acquire the spinlock. Once spinlock is acquired the driver proceeds with the stale value of epfile and tries to free the already freed read buffer causing use-after-free. Following is the illustration of the race: CPU1 CPU2 ffs_func_eps_disable epfiles (local copy) ffs_epfile_release ffs_data_closed if (last file closed) ffs_data_reset ffs_data_clear ffs_epfiles_destroy spin_lock dereference epfiles Fix this races by taking epfiles local copy & assigning it under spinlock and if epfiles(local) is null then update it in ffs->epfiles then finally destroy it. Extending the scope further from the race, protecting the ep related structures, and concurrent accesses.Show less

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: avoid double fput() on failed usercopy If the copy back to userland fails for the FASTRPC_IOCTL_ALLOC_DMA_BUFF ioctl(), we shouldn't assume that 'buf->dmabuf' is still valid. In fact, dma_buf_fd() called fd_install() before, i.e. "consumed" one reference, leaving us with none. Calling dma_buf_put() will therefore put a reference we no longer own, leading to a valid file descritor table entry for an already released 'file' object which is a straight use-after-free. Simply avoid calling dma_buf_put() and rely on the process exit code to do the necessary cleanup, if needed, i.e. if the file descriptor is still valid.Show less

In the Linux kernel, the following vulnerability has been resolved: tcp: take care of mixed splice()/sendmsg(MSG_ZEROCOPY) case syzbot found that mixing sendpage() and sendmsg(MSG_ZEROCOPY) calls over the same TCP socket would again trigger the infamous warning in inet_sock_destruct() WARN_ON(sk_forward_alloc_get(sk)); While Talal took into account a mix of regular copied data and MSG_ZEROCOPY one in the same skb, the sendpage() path has been forgotten. We want the charging to happen for sendpage(), because pages could be coming from a pipe. What is missing is the downgrading of pure zerocopy status to make sure sk_forward_alloc will stay synced. Add tcp_downgrade_zcopy_pure() helper so that we can use it from the two callers.Show less

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6xxx: don't use devres for mdiobus As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The mv88e6xxx is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the Marvell switch driver on shutdown. systemd-shutdown[1]: Powering off. mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down fsl-mc dpbp.9: Removing from iommu group 7 fsl-mc dpbp.8: Removing from iommu group 7 ------------[ cut here ]------------ kernel BUG at drivers/net/phy/mdio_bus.c:677! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15 pc : mdiobus_free+0x44/0x50 lr : devm_mdiobus_free+0x10/0x20 Call trace: mdiobus_free+0x44/0x50 devm_mdiobus_free+0x10/0x20 devres_release_all+0xa0/0x100 __device_release_driver+0x190/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x4c/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x94/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_device_remove+0x24/0x40 __fsl_mc_device_remove+0xc/0x20 device_for_each_child+0x58/0xa0 dprc_remove+0x90/0xb0 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_bus_remove+0x80/0x100 fsl_mc_bus_shutdown+0xc/0x1c platform_shutdown+0x20/0x30 device_shutdown+0x154/0x330 kernel_power_off+0x34/0x6c __do_sys_reboot+0x15c/0x250 __arm64_sys_reboot+0x20/0x30 invoke_syscall.constprop.0+0x4c/0xe0 do_el0_svc+0x4c/0x150 el0_svc+0x24/0xb0 el0t_64_sync_handler+0xa8/0xb0 el0t_64_sync+0x178/0x17c So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The Marvell driver already has a good structure for mdiobus removal, so just plug in mdiobus_free and get rid of devres.Show less

In the Linux kernel, the following vulnerability has been resolved: net: dsa: ar9331: register the mdiobus under devres As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The ar9331 is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the ar9331 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The ar9331 driver doesn't have a complex code structure for mdiobus removal, so just replace of_mdiobus_register with the devres variant in order to be all-devres and ensure that we don't free a still-registered bus.Show less

In the Linux kernel, the following vulnerability has been resolved: SUNRPC: lock against ->sock changing during sysfs read ->sock can be set to NULL asynchronously unless ->recv_mutex is held. So it is important to hold that mutex. Otherwise a sysfs read can trigger an oops. Commit 17f09d3f619a ("SUNRPC: Check if the xprt is connected before handling sysfs reads") appears to attempt to fix this problem, but it only narrows the race window.Show less

In the Linux kernel, the following vulnerability has been resolved: net: dsa: bcm_sf2: don't use devres for mdiobus As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Starfighter 2 is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the bcm_sf2 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The bcm_sf2 driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus.Show less

In the Linux kernel, the following vulnerability has been resolved: net: dsa: seville: register the mdiobus under devres As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Seville VSC9959 switch is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the seville switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The seville driver has a code structure that could accommodate both the mdiobus_unregister and mdiobus_free calls, but it has an external dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls devm_mdiobus_alloc_size() on its behalf. So rather than restructuring that, and exporting yet one more symbol mscc_miim_teardown(), let's work with devres and replace of_mdiobus_register with the devres variant. When we use all-devres, we can ensure that devres doesn't free a still-registered bus (it either runs both callbacks, or none).Show less

In the Linux kernel, the following vulnerability has been resolved: net: dsa: felix: don't use devres for mdiobus As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Felix VSC9959 switch is a PCI device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the felix switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The felix driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc_size() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus.Show less