Linux

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix IPsec RoCE MPV trace call Prevent the call trace below from happening, by not allowing IPsec creation over a slave, if master device doesn't support IPsec. WARNING: CPU: 44 PID: 16136 at kernel/locking/rwsem.c:240 down_read+0x75/0x94 Modules linked in: esp4_offload esp4 act_mirred act_vlan cls_flower sch_ingress mlx5_vdpa vringh vhost_iotlb vdpa mst_pciconf(OE) nfsv3 nfs_acl nfs lockd grace fscache netfs xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 rfkill cuse fuse rpcrdma sunrpc rdma_ucm ib_srpt ib_isert iscsi_target_mod target_core_mod ib_umad ib_iser libiscsi scsi_transport_iscsi rdma_cm ib_ipoib iw_cm ib_cm ipmi_ssif intel_rapl_msr intel_rapl_common amd64_edac edac_mce_amd kvm_amd kvm irqbypass crct10dif_pclmul crc32_pclmul mlx5_ib ghash_clmulni_intel sha1_ssse3 dell_smbios ib_uverbs aesni_intel crypto_simd dcdbas wmi_bmof dell_wmi_descriptor cryptd pcspkr ib_core acpi_ipmi sp5100_tco ccp i2c_piix4 ipmi_si ptdma k10temp ipmi_devintf ipmi_msghandler acpi_power_meter acpi_cpufreq ext4 mbcache jbd2 sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect mlx5_core sysimgblt fb_sys_fops cec ahci libahci mlxfw drm pci_hyperv_intf libata tg3 sha256_ssse3 tls megaraid_sas i2c_algo_bit psample wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mst_pci] CPU: 44 PID: 16136 Comm: kworker/44:3 Kdump: loaded Tainted: GOE 5.15.0-20240509.el8uek.uek7_u3_update_v6.6_ipsec_bf.x86_64 #2 Hardware name: Dell Inc. PowerEdge R7525/074H08, BIOS 2.0.3 01/15/2021 Workqueue: events xfrm_state_gc_task RIP: 0010:down_read+0x75/0x94 Code: 00 48 8b 45 08 65 48 8b 14 25 80 fc 01 00 83 e0 02 48 09 d0 48 83 c8 01 48 89 45 08 5d 31 c0 89 c2 89 c6 89 c7 e9 cb 88 3b 00 <0f> 0b 48 8b 45 08 a8 01 74 b2 a8 02 75 ae 48 89 c2 48 83 ca 02 f0 RSP: 0018:ffffb26387773da8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffa08b658af900 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ff886bc5e1366f2f RDI: 0000000000000000 RBP: ffffa08b658af940 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffa0a9bfb31540 R13: ffffa0a9bfb37900 R14: 0000000000000000 R15: ffffa0a9bfb37905 FS: 0000000000000000(0000) GS:ffffa0a9bfb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055a45ed814e8 CR3: 000000109038a000 CR4: 0000000000350ee0 Call Trace: <TASK> ? show_trace_log_lvl+0x1d6/0x2f9 ? show_trace_log_lvl+0x1d6/0x2f9 ? mlx5_devcom_for_each_peer_begin+0x29/0x60 [mlx5_core] ? down_read+0x75/0x94 ? __warn+0x80/0x113 ? down_read+0x75/0x94 ? report_bug+0xa4/0x11d ? handle_bug+0x35/0x8b ? exc_invalid_op+0x14/0x75 ? asm_exc_invalid_op+0x16/0x1b ? down_read+0x75/0x94 ? down_read+0xe/0x94 mlx5_devcom_for_each_peer_begin+0x29/0x60 [mlx5_core] mlx5_ipsec_fs_roce_tx_destroy+0xb1/0x130 [mlx5_core] tx_destroy+0x1b/0xc0 [mlx5_core] tx_ft_put+0x53/0xc0 [mlx5_core] mlx5e_xfrm_free_state+0x45/0x90 [mlx5_core] ___xfrm_state_destroy+0x10f/0x1a2 xfrm_state_gc_task+0x81/0xa9 process_one_work+0x1f1/0x3c6 worker_thread+0x53/0x3e4 ? process_one_work.cold+0x46/0x3c kthread+0x127/0x144 ? set_kthread_struct+0x60/0x52 ret_from_fork+0x22/0x2d </TASK> ---[ end trace 5ef7896144d398e1 ]---Show less

In the Linux kernel, the following vulnerability has been resolved: netem: fix return value if duplicate enqueue fails There is a bug in netem_enqueue() introduced by commit 5845f706388a ("net: netem: fix skb length BUG_ON in __skb_to_sgvec") that can lead to a use-after-free. This commit made netem_enqueue() always return NET_XMIT_SUCCESS when a packet is duplicated, which can cause the parent qdisc's q.qlen to be mistakenly incremented. When this happens qlen_notify() may be skipped on the parent during destruction, leaving a dangling pointer for some classful qdiscs like DRR. There are two ways for the bug happen: - If the duplicated packet is dropped by rootq->enqueue() and then the original packet is also dropped. - If rootq->enqueue() sends the duplicated packet to a different qdisc and the original packet is dropped. In both cases NET_XMIT_SUCCESS is returned even though no packets are enqueued at the netem qdisc. The fix is to defer the enqueue of the duplicate packet until after the original packet has been guaranteed to return NET_XMIT_SUCCESS.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: move dpu_encoder's connector assignment to atomic_enable() For cases where the crtc's connectors_changed was set without enable/active getting toggled , there is an atomic_enable() call followed by an atomic_disable() but without an atomic_mode_set(). This results in a NULL ptr access for the dpu_encoder_get_drm_fmt() call in the atomic_enable() as the dpu_encoder's connector was cleared in the atomic_disable() but not re-assigned as there was no atomic_mode_set() call. Fix the NULL ptr access by moving the assignment for atomic_enable() and also use drm_atomic_get_new_connector_for_encoder() to get the connector from the atomic_state. Patchwork: https://patchwork.freedesktop.org/patch/606729/Show less

In the Linux kernel, the following vulnerability has been resolved: s390/boot: Avoid possible physmem_info segment corruption When physical memory for the kernel image is allocated it does not consider extra memory required for offsetting the image start to match it with the lower 20 bits of KASLR virtual base address. That might lead to kernel access beyond its memory range.Show less

In the Linux kernel, the following vulnerability has been resolved: nvme: move stopping keep-alive into nvme_uninit_ctrl() Commit 4733b65d82bd ("nvme: start keep-alive after admin queue setup") moves starting keep-alive from nvme_start_ctrl() into nvme_init_ctrl_finish(), but don't move stopping keep-alive into nvme_uninit_ctrl(), so keep-alive work can be started and keep pending after failing to start controller, finally use-after-free is triggered if nvme host driver is unloaded. This patch fixes kernel panic when running nvme/004 in case that connection failure is triggered, by moving stopping keep-alive into nvme_uninit_ctrl(). This way is reasonable because keep-alive is now started in nvme_init_ctrl_finish().Show less

In the Linux kernel, the following vulnerability has been resolved: nouveau/firmware: use dma non-coherent allocator Currently, enabling SG_DEBUG in the kernel will cause nouveau to hit a BUG() on startup, when the iommu is enabled: kernel BUG at include/linux/scatterlist.h:187! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 7 PID: 930 Comm: (udev-worker) Not tainted 6.9.0-rc3Lyude-Test+ #30 Hardware name: MSI MS-7A39/A320M GAMING PRO (MS-7A39), BIOS 1.I0 01/22/2019 RIP: 0010:sg_init_one+0x85/0xa0 Code: 69 88 32 01 83 e1 03 f6 c3 03 75 20 a8 01 75 1e 48 09 cb 41 89 54 24 08 49 89 1c 24 41 89 6c 24 0c 5b 5d 41 5c e9 7b b9 88 00 <0f> 0b 0f 0b 0f 0b 48 8b 05 5e 46 9a 01 eb b2 66 66 2e 0f 1f 84 00 RSP: 0018:ffffa776017bf6a0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa77600d87000 RCX: 000000000000002b RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffa77680d87000 RBP: 000000000000e000 R08: 0000000000000000 R09: 0000000000000000 R10: ffff98f4c46aa508 R11: 0000000000000000 R12: ffff98f4c46aa508 R13: ffff98f4c46aa008 R14: ffffa77600d4a000 R15: ffffa77600d4a018 FS: 00007feeb5aae980(0000) GS:ffff98f5c4dc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f22cb9a4520 CR3: 00000001043ba000 CR4: 00000000003506f0 Call Trace: <TASK> ? die+0x36/0x90 ? do_trap+0xdd/0x100 ? sg_init_one+0x85/0xa0 ? do_error_trap+0x65/0x80 ? sg_init_one+0x85/0xa0 ? exc_invalid_op+0x50/0x70 ? sg_init_one+0x85/0xa0 ? asm_exc_invalid_op+0x1a/0x20 ? sg_init_one+0x85/0xa0 nvkm_firmware_ctor+0x14a/0x250 [nouveau] nvkm_falcon_fw_ctor+0x42/0x70 [nouveau] ga102_gsp_booter_ctor+0xb4/0x1a0 [nouveau] r535_gsp_oneinit+0xb3/0x15f0 [nouveau] ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? nvkm_udevice_new+0x95/0x140 [nouveau] ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? ktime_get+0x47/0xb0 Fix this by using the non-coherent allocator instead, I think there might be a better answer to this, but it involve ripping up some of APIs using sg lists.Show less

In the Linux kernel, the following vulnerability has been resolved: char: xillybus: Check USB endpoints when probing device Ensure, as the driver probes the device, that all endpoints that the driver may attempt to access exist and are of the correct type. All XillyUSB devices must have a Bulk IN and Bulk OUT endpoint at address 1. This is verified in xillyusb_setup_base_eps(). On top of that, a XillyUSB device may have additional Bulk OUT endpoints. The information about these endpoints' addresses is deduced from a data structure (the IDT) that the driver fetches from the device while probing it. These endpoints are checked in setup_channels(). A XillyUSB device never has more than one IN endpoint, as all data towards the host is multiplexed in this single Bulk IN endpoint. This is why setup_channels() only checks OUT endpoints.Show less

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: only mark 'subflow' endp as available Adding the following warning ... WARN_ON_ONCE(msk->pm.local_addr_used == 0) ... before decrementing the local_addr_used counter helped to find a bug when running the "remove single address" subtest from the mptcp_join.sh selftests. Removing a 'signal' endpoint will trigger the removal of all subflows linked to this endpoint via mptcp_pm_nl_rm_addr_or_subflow() with rm_type == MPTCP_MIB_RMSUBFLOW. This will decrement the local_addr_used counter, which is wrong in this case because this counter is linked to 'subflow' endpoints, and here it is a 'signal' endpoint that is being removed. Now, the counter is decremented, only if the ID is being used outside of mptcp_pm_nl_rm_addr_or_subflow(), only for 'subflow' endpoints, and if the ID is not 0 -- local_addr_used is not taking into account these ones. This marking of the ID as being available, and the decrement is done no matter if a subflow using this ID is currently available, because the subflow could have been closed before.Show less

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: only decrement add_addr_accepted for MPJ req Adding the following warning ... WARN_ON_ONCE(msk->pm.add_addr_accepted == 0) ... before decrementing the add_addr_accepted counter helped to find a bug when running the "remove single subflow" subtest from the mptcp_join.sh selftest. Removing a 'subflow' endpoint will first trigger a RM_ADDR, then the subflow closure. Before this patch, and upon the reception of the RM_ADDR, the other peer will then try to decrement this add_addr_accepted. That's not correct because the attached subflows have not been created upon the reception of an ADD_ADDR. A way to solve that is to decrement the counter only if the attached subflow was an MP_JOIN to a remote id that was not 0, and initiated by the host receiving the RM_ADDR.Show less

In the Linux kernel, the following vulnerability has been resolved: media: aspeed: Fix memory overwrite if timing is 1600x900 When capturing 1600x900, system could crash when system memory usage is tight. The way to reproduce this issue: 1. Use 1600x900 to display on host 2. Mount ISO through 'Virtual media' on OpenBMC's web 3. Run script as below on host to do sha continuously #!/bin/bash while [ [1] ]; do find /media -type f -printf '"%h/%f"\n' | xargs sha256sum done 4. Open KVM on OpenBMC's web The size of macro block captured is 8x8. Therefore, we should make sure the height of src-buf is 8 aligned to fix this issue.Show less

In the Linux kernel, the following vulnerability has been resolved: media: dvb-usb-v2: af9035: Fix null-ptr-deref in af9035_i2c_master_xfer In af9035_i2c_master_xfer, msg is controlled by user. When msg[i].buf is null and msg[i].len is zero, former checks on msg[i].buf would be passed. Malicious data finally reach af9035_i2c_master_xfer. If accessing msg[i].buf[0] without sanity check, null ptr deref would happen. We add check on msg[i].len to prevent crash. Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")Show less

In the Linux kernel, the following vulnerability has been resolved: Input: MT - limit max slots syzbot is reporting too large allocation at input_mt_init_slots(), for num_slots is supplied from userspace using ioctl(UI_DEV_CREATE). Since nobody knows possible max slots, this patch chose 1024.Show less

In the Linux kernel, the following vulnerability has been resolved: char: xillybus: Don't destroy workqueue from work item running on it Triggered by a kref decrement, destroy_workqueue() may be called from within a work item for destroying its own workqueue. This illegal situation is averted by adding a module-global workqueue for exclusive use of the offending work item. Other work items continue to be queued on per-device workqueues to ensure performance.Show less

In the Linux kernel, the following vulnerability has been resolved: xhci: Fix Panther point NULL pointer deref at full-speed re-enumeration re-enumerating full-speed devices after a failed address device command can trigger a NULL pointer dereference. Full-speed devices may need to reconfigure the endpoint 0 Max Packet Size value during enumeration. Usb core calls usb_ep0_reinit() in this case, which ends up calling xhci_configure_endpoint(). On Panther point xHC the xhci_configure_endpoint() function will additionally check and reserve bandwidth in software. Other hosts do this in hardware If xHC address device command fails then a new xhci_virt_device structure is allocated as part of re-enabling the slot, but the bandwidth table pointers are not set up properly here. This triggers the NULL pointer dereference the next time usb_ep0_reinit() is called and xhci_configure_endpoint() tries to check and reserve bandwidth [46710.713538] usb 3-1: new full-speed USB device number 5 using xhci_hcd [46710.713699] usb 3-1: Device not responding to setup address. [46710.917684] usb 3-1: Device not responding to setup address. [46711.125536] usb 3-1: device not accepting address 5, error -71 [46711.125594] BUG: kernel NULL pointer dereference, address: 0000000000000008 [46711.125600] #PF: supervisor read access in kernel mode [46711.125603] #PF: error_code(0x0000) - not-present page [46711.125606] PGD 0 P4D 0 [46711.125610] Oops: Oops: 0000 [#1] PREEMPT SMP PTI [46711.125615] CPU: 1 PID: 25760 Comm: kworker/1:2 Not tainted 6.10.3_2 #1 [46711.125620] Hardware name: Gigabyte Technology Co., Ltd. [46711.125623] Workqueue: usb_hub_wq hub_event [usbcore] [46711.125668] RIP: 0010:xhci_reserve_bandwidth (drivers/usb/host/xhci.c Fix this by making sure bandwidth table pointers are set up correctly after a failed address device command, and additionally by avoiding checking for bandwidth in cases like this where no actual endpoints are added or removed, i.e. only context for default control endpoint 0 is evaluated.Show less

In the Linux kernel, the following vulnerability has been resolved: KVM: s390: fix validity interception issue when gisa is switched off We might run into a SIE validity if gisa has been disabled either via using kernel parameter "kvm.use_gisa=0" or by setting the related sysfs attribute to N (echo N >/sys/module/kvm/parameters/use_gisa). The validity is caused by an invalid value in the SIE control block's gisa designation. That happens because we pass the uninitialized gisa origin to virt_to_phys() before writing it to the gisa designation. To fix this we return 0 in kvm_s390_get_gisa_desc() if the origin is 0. kvm_s390_get_gisa_desc() is used to determine which gisa designation to set in the SIE control block. A value of 0 in the gisa designation disables gisa usage. The issue surfaces in the host kernel with the following kernel message as soon a new kvm guest start is attemted. kvm: unhandled validity intercept 0x1011 WARNING: CPU: 0 PID: 781237 at arch/s390/kvm/intercept.c:101 kvm_handle_sie_intercept+0x42e/0x4d0 [kvm] Modules linked in: vhost_net tap tun xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT xt_tcpudp nft_compat x_tables nf_nat_tftp nf_conntrack_tftp vfio_pci_core irqbypass vhost_vsock vmw_vsock_virtio_transport_common vsock vhost vhost_iotlb kvm nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables sunrpc mlx5_ib ib_uverbs ib_core mlx5_core uvdevice s390_trng eadm_sch vfio_ccw zcrypt_cex4 mdev vfio_iommu_type1 vfio sch_fq_codel drm i2c_core loop drm_panel_orientation_quirks configfs nfnetlink lcs ctcm fsm dm_service_time ghash_s390 prng chacha_s390 libchacha aes_s390 des_s390 libdes sha3_512_s390 sha3_256_s390 sha512_s390 sha256_s390 sha1_s390 sha_common dm_mirror dm_region_hash dm_log zfcp scsi_transport_fc scsi_dh_rdac scsi_dh_emc scsi_dh_alua pkey zcrypt dm_multipath rng_core autofs4 [last unloaded: vfio_pci] CPU: 0 PID: 781237 Comm: CPU 0/KVM Not tainted 6.10.0-08682-gcad9f11498ea #6 Hardware name: IBM 3931 A01 701 (LPAR) Krnl PSW : 0704c00180000000 000003d93deb0122 (kvm_handle_sie_intercept+0x432/0x4d0 [kvm]) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3 Krnl GPRS: 000003d900000027 000003d900000023 0000000000000028 000002cd00000000 000002d063a00900 00000359c6daf708 00000000000bebb5 0000000000001eff 000002cfd82e9000 000002cfd80bc000 0000000000001011 000003d93deda412 000003ff8962df98 000003d93de77ce0 000003d93deb011e 00000359c6daf960 Krnl Code: 000003d93deb0112: c020fffe7259 larl %r2,000003d93de7e5c4 000003d93deb0118: c0e53fa8beac brasl %r14,000003d9bd3c7e70 #000003d93deb011e: af000000 mc 0,0 >000003d93deb0122: a728ffea lhi %r2,-22 000003d93deb0126: a7f4fe24 brc 15,000003d93deafd6e 000003d93deb012a: 9101f0b0 tm 176(%r15),1 000003d93deb012e: a774fe48 brc 7,000003d93deafdbe 000003d93deb0132: 40a0f0ae sth %r10,174(%r15) Call Trace: [<000003d93deb0122>] kvm_handle_sie_intercept+0x432/0x4d0 [kvm] ([<000003d93deb011e>] kvm_handle_sie_intercept+0x42e/0x4d0 [kvm]) [<000003d93deacc10>] vcpu_post_run+0x1d0/0x3b0 [kvm] [<000003d93deaceda>] __vcpu_run+0xea/0x2d0 [kvm] [<000003d93dead9da>] kvm_arch_vcpu_ioctl_run+0x16a/0x430 [kvm] [<000003d93de93ee0>] kvm_vcpu_ioctl+0x190/0x7c0 [kvm] [<000003d9bd728b4e>] vfs_ioctl+0x2e/0x70 [<000003d9bd72a092>] __s390x_sys_ioctl+0xc2/0xd0 [<000003d9be0e9222>] __do_syscall+0x1f2/0x2e0 [<000003d9be0f9a90>] system_call+0x70/0x98 Last Breaking-Event-Address: [<000003d9bd3c7f58>] __warn_printk+0xe8/0xf0Show less

In the Linux kernel, the following vulnerability has been resolved: KEYS: trusted: dcp: fix leak of blob encryption key Trusted keys unseal the key blob on load, but keep the sealed payload in the blob field so that every subsequent read (export) will simply convert this field to hex and send it to userspace. With DCP-based trusted keys, we decrypt the blob encryption key (BEK) in the Kernel due hardware limitations and then decrypt the blob payload. BEK decryption is done in-place which means that the trusted key blob field is modified and it consequently holds the BEK in plain text. Every subsequent read of that key thus send the plain text BEK instead of the encrypted BEK to userspace. This issue only occurs when importing a trusted DCP-based key and then exporting it again. This should rarely happen as the common use cases are to either create a new trusted key and export it, or import a key blob and then just use it without exporting it again. Fix this by performing BEK decryption and encryption in a dedicated buffer. Further always wipe the plain text BEK buffer to prevent leaking the key via uninitialized memory.Show less

In the Linux kernel, the following vulnerability has been resolved: vfs: Don't evict inode under the inode lru traversing context The inode reclaiming process(See function prune_icache_sb) collects all reclaimable inodes and mark them with I_FREEING flag at first, at that time, other processes will be stuck if they try getting these inodes (See function find_inode_fast), then the reclaiming process destroy the inodes by function dispose_list(). Some filesystems(eg. ext4 with ea_inode feature, ubifs with xattr) may do inode lookup in the inode evicting callback function, if the inode lookup is operated under the inode lru traversing context, deadlock problems may happen. Case 1: In function ext4_evict_inode(), the ea inode lookup could happen if ea_inode feature is enabled, the lookup process will be stuck under the evicting context like this: 1. File A has inode i_reg and an ea inode i_ea 2. getfattr(A, xattr_buf) // i_ea is added into lru // lru->i_ea 3. Then, following three processes running like this: PA PB echo 2 > /proc/sys/vm/drop_caches shrink_slab prune_dcache_sb // i_reg is added into lru, lru->i_ea->i_reg prune_icache_sb list_lru_walk_one inode_lru_isolate i_ea->i_state |= I_FREEING // set inode state inode_lru_isolate __iget(i_reg) spin_unlock(&i_reg->i_lock) spin_unlock(lru_lock) rm file A i_reg->nlink = 0 iput(i_reg) // i_reg->nlink is 0, do evict ext4_evict_inode ext4_xattr_delete_inode ext4_xattr_inode_dec_ref_all ext4_xattr_inode_iget ext4_iget(i_ea->i_ino) iget_locked find_inode_fast __wait_on_freeing_inode(i_ea) ----→ AA deadlock dispose_list // cannot be executed by prune_icache_sb wake_up_bit(&i_ea->i_state) Case 2: In deleted inode writing function ubifs_jnl_write_inode(), file deleting process holds BASEHD's wbuf->io_mutex while getting the xattr inode, which could race with inode reclaiming process(The reclaiming process could try locking BASEHD's wbuf->io_mutex in inode evicting function), then an ABBA deadlock problem would happen as following: 1. File A has inode ia and a xattr(with inode ixa), regular file B has inode ib and a xattr. 2. getfattr(A, xattr_buf) // ixa is added into lru // lru->ixa 3. Then, following three processes running like this: PA PB PC echo 2 > /proc/sys/vm/drop_caches shrink_slab prune_dcache_sb // ib and ia are added into lru, lru->ixa->ib->ia prune_icache_sb list_lru_walk_one inode_lru_isolate ixa->i_state |= I_FREEING // set inode state inode_lru_isolate __iget(ib) spin_unlock(&ib->i_lock) spin_unlock(lru_lock) rm file B ib->nlink = 0 rm file A iput(ia) ubifs_evict_inode(ia) ubifs_jnl_delete_inode(ia) ubifs_jnl_write_inode(ia) make_reservation(BASEHD) // Lock wbuf->io_mutex ubifs_iget(ixa->i_ino) iget_locked find_inode_fast __wait_on_freeing_inode(ixa) | iput(ib) // ib->nlink is 0, do evict | ubifs_evict_inode | ubifs_jnl_delete_inode(ib) ↓ ubifs_jnl_write_inode ABBA deadlock ←-----make_reservation(BASEHD) dispose_list // cannot be executed by prune_icache_sb wake_up_bit(&ixa->i_state) Fix the possible deadlock by using new inode state flag I_LRU_ISOLATING to pin the inode in memory while inode_lru_isolate( ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: rtla/osnoise: Prevent NULL dereference in error handling If the "tool->data" allocation fails then there is no need to call osnoise_free_top() and, in fact, doing so will lead to a NULL dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: net: mana: Fix RX buf alloc_size alignment and atomic op panic The MANA driver's RX buffer alloc_size is passed into napi_build_skb() to create SKB. skb_shinfo(skb) is located at the end of skb, and its alignment is affected by the alloc_size passed into napi_build_skb(). The size needs to be aligned properly for better performance and atomic operations. Otherwise, on ARM64 CPU, for certain MTU settings like 4000, atomic operations may panic on the skb_shinfo(skb)->dataref due to alignment fault. To fix this bug, add proper alignment to the alloc_size calculation. Sample panic info: [ 253.298819] Unable to handle kernel paging request at virtual address ffff000129ba5cce [ 253.300900] Mem abort info: [ 253.301760] ESR = 0x0000000096000021 [ 253.302825] EC = 0x25: DABT (current EL), IL = 32 bits [ 253.304268] SET = 0, FnV = 0 [ 253.305172] EA = 0, S1PTW = 0 [ 253.306103] FSC = 0x21: alignment fault Call trace: __skb_clone+0xfc/0x198 skb_clone+0x78/0xe0 raw6_local_deliver+0xfc/0x228 ip6_protocol_deliver_rcu+0x80/0x500 ip6_input_finish+0x48/0x80 ip6_input+0x48/0xc0 ip6_sublist_rcv_finish+0x50/0x78 ip6_sublist_rcv+0x1cc/0x2b8 ipv6_list_rcv+0x100/0x150 __netif_receive_skb_list_core+0x180/0x220 netif_receive_skb_list_internal+0x198/0x2a8 __napi_poll+0x138/0x250 net_rx_action+0x148/0x330 handle_softirqs+0x12c/0x3a0Show less