Linux

In the Linux kernel, the following vulnerability has been resolved: mcb: fix a double free bug in chameleon_parse_gdd() In chameleon_parse_gdd(), if mcb_device_register() fails, 'mdev' would be released in mcb_device_register() via put_device(). Thus, goto 'err' label and free 'mdev' again causes a double free. Just return if mcb_device_register() fails.Show less

In the Linux kernel, the following vulnerability has been resolved: mei: vsc: Fix fortify-panic caused by invalid counted_by() use gcc 15 honors the __counted_by(len) attribute on vsc_tp_packet.buf[] and the vsc-tp.c code is using this in a wrong way. len does not contain the available size in the buffer, it contains the actual packet length *without* the crc. So as soon as vsc_tp_xfer() tries to add the crc to buf[] the fortify-panic handler gets triggered: [ 80.842193] memcpy: detected buffer overflow: 4 byte write of buffer size 0 [ 80.842243] WARNING: CPU: 4 PID: 272 at lib/string_helpers.c:1032 __fortify_report+0x45/0x50 ... [ 80.843175] __fortify_panic+0x9/0xb [ 80.843186] vsc_tp_xfer.cold+0x67/0x67 [mei_vsc_hw] [ 80.843210] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 80.843229] ? lockdep_hardirqs_on+0x7c/0x110 [ 80.843250] mei_vsc_hw_start+0x98/0x120 [mei_vsc] [ 80.843270] mei_reset+0x11d/0x420 [mei] The easiest fix would be to just drop the counted-by but with the exception of the ack buffer in vsc_tp_xfer_helper() which only contains enough room for the packet-header, all other uses of vsc_tp_packet always use a buffer of VSC_TP_MAX_XFER_SIZE bytes for the packet. Instead of just dropping the counted-by, split the vsc_tp_packet struct definition into a header and a full-packet definition and use a fixed size buf[] in the packet definition, this way fortify-source buffer overrun checking still works when enabled.Show less

In the Linux kernel, the following vulnerability has been resolved: misc: microchip: pci1xxxx: Fix Kernel panic during IRQ handler registration Resolve kernel panic while accessing IRQ handler associated with the generated IRQ. This is done by acquiring the spinlock and storing the current interrupt state before handling the interrupt request using generic_handle_irq. A previous fix patch was submitted where 'generic_handle_irq' was replaced with 'handle_nested_irq'. However, this change also causes the kernel panic where after determining which GPIO triggered the interrupt and attempting to call handle_nested_irq with the mapped IRQ number, leads to a failure in locating the registered handler.Show less

In the Linux kernel, the following vulnerability has been resolved: tty: Require CAP_SYS_ADMIN for all usages of TIOCL_SELMOUSEREPORT This requirement was overeagerly loosened in commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as it turns out, (1) the logic I implemented there was inconsistent (apologies!), (2) TIOCL_SELMOUSEREPORT might actually be a small security risk after all, and (3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN already. In more detail: 1. The previous patch has inconsistent logic: In commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), we checked for sel_mode == TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of this "mode" parameter were actually used as an additional way to pass an argument. So the patch did actually still require CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not require it if none of the mouse buttons bits are set. This logic is inconsistent and was not intentional. We should have the same policies for using TIOCL_SELMOUSEREPORT independent of the value of the "hidden" mouse button argument. I sent a separate documentation patch to the man page list with more details on TIOCL_SELMOUSEREPORT: https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/ 2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can let an attacker simulate "keyboard" input to command line applications on the same terminal, like TIOCSTI and some other TIOCLINUX "selection mode" IOCTLs. By enabling mouse reporting on a terminal and then injecting mouse reports through TIOCL_SELMOUSEREPORT, an attacker can simulate mouse movements on the same terminal, similar to the TIOCSTI keystroke injection attacks that were previously possible with TIOCSTI and other TIOCL_SETSEL selection modes. Many programs (including libreadline/bash) are then prone to misinterpret these mouse reports as normal keyboard input because they do not expect input in the X11 mouse protocol form. The attacker does not have complete control over the escape sequence, but they can at least control the values of two consecutive bytes in the binary mouse reporting escape sequence. I went into more detail on that in the discussion at https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/ It is not equally trivial to simulate arbitrary keystrokes as it was with TIOCSTI (commit 83efeeeb3d04 ("tty: Allow TIOCSTI to be disabled")), but the general mechanism is there, and together with the small number of existing legit use cases (see below), it would be better to revert back to requiring CAP_SYS_ADMIN for TIOCL_SELMOUSEREPORT, as it was already the case before commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"). 3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or Consolation), and they are the only legit use case: To quote console_codes(4): The mouse tracking facility is intended to return xterm(1)-compatible mouse status reports. Because the console driver has no way to know the device or type of the mouse, these reports are returned in the console input stream only when the virtual terminal driver receives a mouse update ioctl. These ioctls must be generated by a mouse-aware user-mode application such as the gpm(8) daemon. Jared Finder has also confirmed in https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/ that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it would be difficult to find good reasons for doing that, given that it would interfere with the reports that GPM is sending. More information on the interaction between GPM, terminals and th ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: usb: xhci: Fix invalid pointer dereference in Etron workaround This check is performed before prepare_transfer() and prepare_ring(), so enqueue can already point at the final link TRB of a segment. And indeed it will, some 0.4% of times this code is called. Then enqueue + 1 is an invalid pointer. It will crash the kernel right away or load some junk which may look like a link TRB and cause the real link TRB to be replaced with a NOOP. This wouldn't end well. Use a functionally equivalent test which doesn't dereference the pointer and always gives correct result. Something has crashed my machine twice in recent days while playing with an Etron HC, and a control transfer stress test ran for confirmation has just crashed it again. The same test passes with this patch applied.Show less

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: Fix deadlock when using NCM gadget The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget"). Under PREEMPT_RT the deadlock can be readily triggered by heavy network traffic, for example using "iperf --bidir" over NCM ethernet link. The deadlock occurs because the threaded interrupt handler gets preempted by a softirq, but both are protected by the same spinlock. Prevent deadlock by disabling softirq during threaded irq handler.Show less

In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: ci_hdrc_imx: fix usbmisc handling usbmisc is an optional device property so it is totally valid for the corresponding data->usbmisc_data to have a NULL value. Check that before dereferencing the pointer. Found by Linux Verification Center (linuxtesting.org) with Svace static analysis tool.Show less

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: check that event count does not exceed event buffer length The event count is read from register DWC3_GEVNTCOUNT. There is a check for the count being zero, but not for exceeding the event buffer length. Check that event count does not exceed event buffer length, avoiding an out-of-bounds access when memcpy'ing the event. Crash log: Unable to handle kernel paging request at virtual address ffffffc0129be000 pc : __memcpy+0x114/0x180 lr : dwc3_check_event_buf+0xec/0x348 x3 : 0000000000000030 x2 : 000000000000dfc4 x1 : ffffffc0129be000 x0 : ffffff87aad60080 Call trace: __memcpy+0x114/0x180 dwc3_interrupt+0x24/0x34Show less

In the Linux kernel, the following vulnerability has been resolved: usb: typec: class: Fix NULL pointer access Concurrent calls to typec_partner_unlink_device can lead to a NULL pointer dereference. This patch adds a mutex to protect USB device pointers and prevent this issue. The same mutex protects both the device pointers and the partner device registration.Show less

In the Linux kernel, the following vulnerability has been resolved: crypto: null - Use spin lock instead of mutex As the null algorithm may be freed in softirq context through af_alg, use spin locks instead of mutexes to protect the default null algorithm.Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix kmemleak warning for percpu hashmap Vlad Poenaru reported the following kmemleak issue: unreferenced object 0x606fd7c44ac8 (size 32): backtrace (crc 0): pcpu_alloc_noprof+0x730/0xeb0 bpf_map_alloc_percpu+0x69/0xc0 prealloc_init+0x9d/0x1b0 htab_map_alloc+0x363/0x510 map_create+0x215/0x3a0 __sys_bpf+0x16b/0x3e0 __x64_sys_bpf+0x18/0x20 do_syscall_64+0x7b/0x150 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Further investigation shows the reason is due to not 8-byte aligned store of percpu pointer in htab_elem_set_ptr(): *(void __percpu **)(l->key + key_size) = pptr; Note that the whole htab_elem alignment is 8 (for x86_64). If the key_size is 4, that means pptr is stored in a location which is 4 byte aligned but not 8 byte aligned. In mm/kmemleak.c, scan_block() scans the memory based on 8 byte stride, so it won't detect above pptr, hence reporting the memory leak. In htab_map_alloc(), we already have htab->elem_size = sizeof(struct htab_elem) + round_up(htab->map.key_size, 8); if (percpu) htab->elem_size += sizeof(void *); else htab->elem_size += round_up(htab->map.value_size, 8); So storing pptr with 8-byte alignment won't cause any problem and can fix kmemleak too. The issue can be reproduced with bpf selftest as well: 1. Enable CONFIG_DEBUG_KMEMLEAK config 2. Add a getchar() before skel destroy in test_hash_map() in prog_tests/for_each.c. The purpose is to keep map available so kmemleak can be detected. 3. run './test_progs -t for_each/hash_map &' and a kmemleak should be reported.Show less

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Keep write operations atomic syzbot reported a NULL pointer dereference in __generic_file_write_iter. [1] Before the write operation is completed, the user executes ioctl[2] to clear the compress flag of the file, which causes the is_compressed() judgment to return 0, further causing the program to enter the wrong process and call the wrong ops ntfs_aops_cmpr, which triggers the null pointer dereference of write_begin. Use inode lock to synchronize ioctl and write to avoid this case. [1] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000086000006 EC = 0x21: IABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault user pgtable: 4k pages, 48-bit VAs, pgdp=000000011896d000 [0000000000000000] pgd=0800000118b44403, p4d=0800000118b44403, pud=0800000117517403, pmd=0000000000000000 Internal error: Oops: 0000000086000006 [#1] PREEMPT SMP Modules linked in: CPU: 0 UID: 0 PID: 6427 Comm: syz-executor347 Not tainted 6.13.0-rc3-syzkaller-g573067a5a685 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0x0 lr : generic_perform_write+0x29c/0x868 mm/filemap.c:4055 sp : ffff80009d4978a0 x29: ffff80009d4979c0 x28: dfff800000000000 x27: ffff80009d497bc8 x26: 0000000000000000 x25: ffff80009d497960 x24: ffff80008ba71c68 x23: 0000000000000000 x22: ffff0000c655dac0 x21: 0000000000001000 x20: 000000000000000c x19: 1ffff00013a92f2c x18: ffff0000e183aa1c x17: 0004060000000014 x16: ffff800083275834 x15: 0000000000000001 x14: 0000000000000000 x13: 0000000000000001 x12: ffff0000c655dac0 x11: 0000000000ff0100 x10: 0000000000ff0100 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : ffff80009d497980 x4 : ffff80009d497960 x3 : 0000000000001000 x2 : 0000000000000000 x1 : ffff0000e183a928 x0 : ffff0000d60b0fc0 Call trace: 0x0 (P) __generic_file_write_iter+0xfc/0x204 mm/filemap.c:4156 ntfs_file_write_iter+0x54c/0x630 fs/ntfs3/file.c:1267 new_sync_write fs/read_write.c:586 [inline] vfs_write+0x920/0xcf4 fs/read_write.c:679 ksys_write+0x15c/0x26c fs/read_write.c:731 __do_sys_write fs/read_write.c:742 [inline] __se_sys_write fs/read_write.c:739 [inline] __arm64_sys_write+0x7c/0x90 fs/read_write.c:739 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151 el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x84/0x108 arch/arm64/kernel/entry-common.c:762 [2] ioctl$FS_IOC_SETFLAGS(r0, 0x40086602, &(0x7f00000000c0)=0x20)Show less

In the Linux kernel, the following vulnerability has been resolved: sound/virtio: Fix cancel_sync warnings on uninitialized work_structs Betty reported hitting the following warning: [ 8.709131][ T221] WARNING: CPU: 2 PID: 221 at kernel/workqueue.c:4182 ... [ 8.713282][ T221] Call trace: [ 8.713365][ T221] __flush_work+0x8d0/0x914 [ 8.713468][ T221] __cancel_work_sync+0xac/0xfc [ 8.713570][ T221] cancel_work_sync+0x24/0x34 [ 8.713667][ T221] virtsnd_remove+0xa8/0xf8 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276] [ 8.713868][ T221] virtsnd_probe+0x48c/0x664 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276] [ 8.714035][ T221] virtio_dev_probe+0x28c/0x390 [ 8.714139][ T221] really_probe+0x1bc/0x4c8 ... It seems we're hitting the error path in virtsnd_probe(), which triggers a virtsnd_remove() which iterates over the substreams calling cancel_work_sync() on the elapsed_period work_struct. Looking at the code, from earlier in: virtsnd_probe()->virtsnd_build_devs()->virtsnd_pcm_parse_cfg() We set snd->nsubstreams, allocate the snd->substreams, and if we then hit an error on the info allocation or something in virtsnd_ctl_query_info() fails, we will exit without having initialized the elapsed_period work_struct. When that error path unwinds we then call virtsnd_remove() which as long as the substreams array is allocated, will iterate through calling cancel_work_sync() on the uninitialized work struct hitting this warning. Takashi Iwai suggested this fix, which initializes the substreams structure right after allocation, so that if we hit the error paths we avoid trying to cleanup uninitialized data. Note: I have not yet managed to reproduce the issue myself, so this patch has had limited testing. Feedback or thoughts would be appreciated!Show less

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix WARNING "do not call blocking ops when !TASK_RUNNING" wait_event_timeout() will set the state of the current task to TASK_UNINTERRUPTIBLE, before doing the condition check. This means that ksmbd_durable_scavenger_alive() will try to acquire the mutex while already in a sleeping state. The scheduler warns us by giving the following warning: do not call blocking ops when !TASK_RUNNING; state=2 set at [<0000000061515a6f>] prepare_to_wait_event+0x9f/0x6c0 WARNING: CPU: 2 PID: 4147 at kernel/sched/core.c:10099 __might_sleep+0x12f/0x160 mutex lock is not needed in ksmbd_durable_scavenger_alive().Show less

In the Linux kernel, the following vulnerability has been resolved: spi: spi-imx: Add check for spi_imx_setupxfer() Add check for the return value of spi_imx_setupxfer(). spi_imx->rx and spi_imx->tx function pointer can be NULL when spi_imx_setupxfer() return error, and make NULL pointer dereference. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: 0x0 spi_imx_pio_transfer+0x50/0xd8 spi_imx_transfer_one+0x18c/0x858 spi_transfer_one_message+0x43c/0x790 __spi_pump_transfer_message+0x238/0x5d4 __spi_sync+0x2b0/0x454 spi_write_then_read+0x11c/0x200Show less

In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential NULL pointer dereference in dev_uevent() If userspace reads "uevent" device attribute at the same time as another threads unbinds the device from its driver, change to dev->driver from a valid pointer to NULL may result in crash. Fix this by using READ_ONCE() when fetching the pointer, and take bus' drivers klist lock to make sure driver instance will not disappear while we access it. Use WRITE_ONCE() when setting the driver pointer to ensure there is no tearing.Show less

In the Linux kernel, the following vulnerability has been resolved: net_sched: keep alloc_hash updated after hash allocation In commit 599be01ee567 ("net_sched: fix an OOB access in cls_tcindex") I moved cp->hash calculation before the first tcindex_alloc_perfect_hash(), but cp->alloc_hash is left untouched. This difference could lead to another out of bound access. cp->alloc_hash should always be the size allocated, we should update it after this tcindex_alloc_perfect_hash().Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: consider that tail calls invalidate packet pointers Tail-called programs could execute any of the helpers that invalidate packet pointers. Hence, conservatively assume that each tail call invalidates packet pointers. Making the change in bpf_helper_changes_pkt_data() automatically makes use of check_cfg() logic that computes 'changes_pkt_data' effect for global sub-programs, such that the following program could be rejected: int tail_call(struct __sk_buff *sk) { bpf_tail_call_static(sk, &jmp_table, 0); return 0; } SEC("tc") int not_safe(struct __sk_buff *sk) { int *p = (void *)(long)sk->data; ... make p valid ... tail_call(sk); *p = 42; /* this is unsafe */ ... } The tc_bpf2bpf.c:subprog_tc() needs change: mark it as a function that can invalidate packet pointers. Otherwise, it can't be freplaced with tailcall_freplace.c:entry_freplace() that does a tail call.Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: check changes_pkt_data property for extension programs When processing calls to global sub-programs, verifier decides whether to invalidate all packet pointers in current state depending on the changes_pkt_data property of the global sub-program. Because of this, an extension program replacing a global sub-program must be compatible with changes_pkt_data property of the sub-program being replaced. This commit: - adds changes_pkt_data flag to struct bpf_prog_aux: - this flag is set in check_cfg() for main sub-program; - in jit_subprogs() for other sub-programs; - modifies bpf_check_attach_btf_id() to check changes_pkt_data flag; - moves call to check_attach_btf_id() after the call to check_cfg(), because it needs changes_pkt_data flag to be set: bpf_check: ... ... - check_attach_btf_id resolve_pseudo_ldimm64 resolve_pseudo_ldimm64 --> bpf_prog_is_offloaded bpf_prog_is_offloaded check_cfg check_cfg + check_attach_btf_id ... ... The following fields are set by check_attach_btf_id(): - env->ops - prog->aux->attach_btf_trace - prog->aux->attach_func_name - prog->aux->attach_func_proto - prog->aux->dst_trampoline - prog->aux->mod - prog->aux->saved_dst_attach_type - prog->aux->saved_dst_prog_type - prog->expected_attach_type Neither of these fields are used by resolve_pseudo_ldimm64() or bpf_prog_offload_verifier_prep() (for netronome and netdevsim drivers), so the reordering is safe.Show less