Linux

In the Linux kernel, the following vulnerability has been resolved: drm/bridge: sii902x: Fix probing race issue A null pointer dereference crash has been observed rarely on TI platforms using sii9022 bridge: [ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x] [ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x] [ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm] [ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper] [ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper] [ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm] [ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper] [ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper] [ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper] [ 53.326401] drm_client_register+0x5c/0xa0 [drm] [ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper] [ 53.336881] tidss_probe+0x128/0x264 [tidss] [ 53.341174] platform_probe+0x68/0xc4 [ 53.344841] really_probe+0x188/0x3c4 [ 53.348501] __driver_probe_device+0x7c/0x16c [ 53.352854] driver_probe_device+0x3c/0x10c [ 53.357033] __device_attach_driver+0xbc/0x158 [ 53.361472] bus_for_each_drv+0x88/0xe8 [ 53.365303] __device_attach+0xa0/0x1b4 [ 53.369135] device_initial_probe+0x14/0x20 [ 53.373314] bus_probe_device+0xb0/0xb4 [ 53.377145] deferred_probe_work_func+0xcc/0x124 [ 53.381757] process_one_work+0x1f0/0x518 [ 53.385770] worker_thread+0x1e8/0x3dc [ 53.389519] kthread+0x11c/0x120 [ 53.392750] ret_from_fork+0x10/0x20 The issue here is as follows: - tidss probes, but is deferred as sii902x is still missing. - sii902x starts probing and enters sii902x_init(). - sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from DRM's perspective. - sii902x calls sii902x_audio_codec_init() and platform_device_register_data() - The registration of the audio platform device causes probing of the deferred devices. - tidss probes, which eventually causes sii902x_bridge_get_edid() to be called. - sii902x_bridge_get_edid() tries to use the i2c to read the edid. However, the sii902x driver has not set up the i2c part yet, leading to the crash. Fix this by moving the drm_bridge_add() to the end of the sii902x_init(), which is also at the very end of sii902x_probe().Show less

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range When running an SVA case, the following soft lockup is triggered: -------------------------------------------------------------------- watchdog: BUG: soft lockup - CPU#244 stuck for 26s! pstate: 83400009 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 lr : arm_smmu_cmdq_issue_cmdlist+0x150/0xa50 sp : ffff8000d83ef290 x29: ffff8000d83ef290 x28: 000000003b9aca00 x27: 0000000000000000 x26: ffff8000d83ef3c0 x25: da86c0812194a0e8 x24: 0000000000000000 x23: 0000000000000040 x22: ffff8000d83ef340 x21: ffff0000c63980c0 x20: 0000000000000001 x19: ffff0000c6398080 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: ffff3000b4a3bbb0 x14: ffff3000b4a30888 x13: ffff3000b4a3cf60 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc08120e4d6bc x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000048cfa x5 : 0000000000000000 x4 : 0000000000000001 x3 : 000000000000000a x2 : 0000000080000000 x1 : 0000000000000000 x0 : 0000000000000001 Call trace: arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 __arm_smmu_tlb_inv_range+0x118/0x254 arm_smmu_tlb_inv_range_asid+0x6c/0x130 arm_smmu_mm_invalidate_range+0xa0/0xa4 __mmu_notifier_invalidate_range_end+0x88/0x120 unmap_vmas+0x194/0x1e0 unmap_region+0xb4/0x144 do_mas_align_munmap+0x290/0x490 do_mas_munmap+0xbc/0x124 __vm_munmap+0xa8/0x19c __arm64_sys_munmap+0x28/0x50 invoke_syscall+0x78/0x11c el0_svc_common.constprop.0+0x58/0x1c0 do_el0_svc+0x34/0x60 el0_svc+0x2c/0xd4 el0t_64_sync_handler+0x114/0x140 el0t_64_sync+0x1a4/0x1a8 -------------------------------------------------------------------- Note that since 6.6-rc1 the arm_smmu_mm_invalidate_range above is renamed to "arm_smmu_mm_arch_invalidate_secondary_tlbs", yet the problem remains. The commit 06ff87bae8d3 ("arm64: mm: remove unused functions and variable protoypes") fixed a similar lockup on the CPU MMU side. Yet, it can occur to SMMU too, since arm_smmu_mm_arch_invalidate_secondary_tlbs() is called typically next to MMU tlb flush function, e.g. tlb_flush_mmu_tlbonly { tlb_flush { __flush_tlb_range { // check MAX_TLBI_OPS } } mmu_notifier_arch_invalidate_secondary_tlbs { arm_smmu_mm_arch_invalidate_secondary_tlbs { // does not check MAX_TLBI_OPS } } } Clone a CMDQ_MAX_TLBI_OPS from the MAX_TLBI_OPS in tlbflush.h, since in an SVA case SMMU uses the CPU page table, so it makes sense to align with the tlbflush code. Then, replace per-page TLBI commands with a single per-asid TLBI command, if the request size hits this threshold.Show less

In the Linux kernel, the following vulnerability has been resolved: mctp: perform route lookups under a RCU read-side lock Our current route lookups (mctp_route_lookup and mctp_route_lookup_null) traverse the net's route list without the RCU read lock held. This means the route lookup is subject to preemption, resulting in an potential grace period expiry, and so an eventual kfree() while we still have the route pointer. Add the proper read-side critical section locks around the route lookups, preventing premption and a possible parallel kfree. The remaining net->mctp.routes accesses are already under a rcu_read_lock, or protected by the RTNL for updates. Based on an analysis from Sili Luo <rootlab@huawei.com>, where introducing a delay in the route lookup could cause a UAF on simultaneous sendmsg() and route deletion.Show less

In the Linux kernel, the following vulnerability has been resolved: x86/srso: Add SRSO mitigation for Hygon processors Add mitigation for the speculative return stack overflow vulnerability which exists on Hygon processors too.Show less

In the Linux kernel, the following vulnerability has been resolved: arm64: errata: Add Cortex-A520 speculative unprivileged load workaround Implement the workaround for ARM Cortex-A520 erratum 2966298. On an affected Cortex-A520 core, a speculatively executed unprivileged load might leak data from a privileged load via a cache side channel. The issue only exists for loads within a translation regime with the same translation (e.g. same ASID and VMID). Therefore, the issue only affects the return to EL0. The workaround is to execute a TLBI before returning to EL0 after all loads of privileged data. A non-shareable TLBI to any address is sufficient. The workaround isn't necessary if page table isolation (KPTI) is enabled, but for simplicity it will be. Page table isolation should normally be disabled for Cortex-A520 as it supports the CSV3 feature and the E0PD feature (used when KASLR is enabled).Show less

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix race condition between session lookup and expire Thread A + Thread B ksmbd_session_lookup | smb2_sess_setup sess = xa_load | | | xa_erase(&conn->sessions, sess->id); | | ksmbd_session_destroy(sess) --> kfree(sess) | // UAF! | sess->last_active = jiffies | + This patch add rwsem to fix race condition between ksmbd_session_lookup and ksmbd_expire_session.Show less

In the Linux kernel, the following vulnerability has been resolved: HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU) races when it races with itself. hidpp_connect_event() primarily runs from a workqueue but it also runs on probe() and if a "device-connected" packet is received by the hw when the thread running hidpp_connect_event() from probe() is waiting on the hw, then a second thread running hidpp_connect_event() will be started from the workqueue. This opens the following races (note the below code is simplified): 1. Retrieving + printing the protocol (harmless race): if (!hidpp->protocol_major) { hidpp_root_get_protocol_version() hidpp->protocol_major = response.rap.params[0]; } We can actually see this race hit in the dmesg in the abrt output attached to rhbz#2227968: [ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. [ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. Testing with extra logging added has shown that after this the 2 threads take turn grabbing the hw access mutex (send_mutex) so they ping-pong through all the other TOCTOU cases managing to hit all of them: 2. Updating the name to the HIDPP name (harmless race): if (hidpp->name == hdev->name) { ... hidpp->name = new_name; } 3. Initializing the power_supply class for the battery (problematic!): hidpp_initialize_battery() { if (hidpp->battery.ps) return 0; probe_battery(); /* Blocks, threads take turns executing this */ hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); } 4. Creating delayed input_device (potentially problematic): if (hidpp->delayed_input) return; hidpp->delayed_input = hidpp_allocate_input(hdev); The really big problem here is 3. Hitting the race leads to the following sequence: hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); ... hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); So now we have registered 2 power supplies for the same battery, which looks a bit weird from userspace's pov but this is not even the really big problem. Notice how: 1. This is all devm-maganaged 2. The hidpp->battery.desc struct is shared between the 2 power supplies 3. hidpp->battery.desc.properties points to the result from the second devm_kmemdup() This causes a use after free scenario on USB disconnect of the receiver: 1. The last registered power supply class device gets unregistered 2. The memory from the last devm_kmemdup() call gets freed, hidpp->battery.desc.properties now points to freed memory 3. The first registered power supply class device gets unregistered, this involves sending a remove uevent to userspace which invokes power_supply_uevent() to fill the uevent data 4. power_supply_uevent() uses hidpp->battery.desc.properties which now points to freed memory leading to backtraces like this one: Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08 ... Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0 ... Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0 Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0 Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680 Sep 22 20:01:35 eric kernel: ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: usb: hub: Guard against accesses to uninitialized BOS descriptors Many functions in drivers/usb/core/hub.c and drivers/usb/core/hub.h access fields inside udev->bos without checking if it was allocated and initialized. If usb_get_bos_descriptor() fails for whatever reason, udev->bos will be NULL and those accesses will result in a crash: BUG: kernel NULL pointer dereference, address: 0000000000000018 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 5 PID: 17818 Comm: kworker/5:1 Tainted: G W 5.15.108-18910-gab0e1cb584e1 #1 <HASH:1f9e 1> Hardware name: Google Kindred/Kindred, BIOS Google_Kindred.12672.413.0 02/03/2021 Workqueue: usb_hub_wq hub_event RIP: 0010:hub_port_reset+0x193/0x788 Code: 89 f7 e8 20 f7 15 00 48 8b 43 08 80 b8 96 03 00 00 03 75 36 0f b7 88 92 03 00 00 81 f9 10 03 00 00 72 27 48 8b 80 a8 03 00 00 <48> 83 78 18 00 74 19 48 89 df 48 8b 75 b0 ba 02 00 00 00 4c 89 e9 RSP: 0018:ffffab740c53fcf8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa1bc5f678000 RCX: 0000000000000310 RDX: fffffffffffffdff RSI: 0000000000000286 RDI: ffffa1be9655b840 RBP: ffffab740c53fd70 R08: 00001b7d5edaa20c R09: ffffffffb005e060 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: ffffab740c53fd3e R14: 0000000000000032 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffa1be96540000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000022e80c005 CR4: 00000000003706e0 Call Trace: hub_event+0x73f/0x156e ? hub_activate+0x5b7/0x68f process_one_work+0x1a2/0x487 worker_thread+0x11a/0x288 kthread+0x13a/0x152 ? process_one_work+0x487/0x487 ? kthread_associate_blkcg+0x70/0x70 ret_from_fork+0x1f/0x30 Fall back to a default behavior if the BOS descriptor isn't accessible and skip all the functionalities that depend on it: LPM support checks, Super Speed capabilitiy checks, U1/U2 states setup.Show less

In the Linux kernel, the following vulnerability has been resolved: perf/x86/lbr: Filter vsyscall addresses We found that a panic can occur when a vsyscall is made while LBR sampling is active. If the vsyscall is interrupted (NMI) for perf sampling, this call sequence can occur (most recent at top): __insn_get_emulate_prefix() insn_get_emulate_prefix() insn_get_prefixes() insn_get_opcode() decode_branch_type() get_branch_type() intel_pmu_lbr_filter() intel_pmu_handle_irq() perf_event_nmi_handler() Within __insn_get_emulate_prefix() at frame 0, a macro is called: peek_nbyte_next(insn_byte_t, insn, i) Within this macro, this dereference occurs: (insn)->next_byte Inspecting registers at this point, the value of the next_byte field is the address of the vsyscall made, for example the location of the vsyscall version of gettimeofday() at 0xffffffffff600000. The access to an address in the vsyscall region will trigger an oops due to an unhandled page fault. To fix the bug, filtering for vsyscalls can be done when determining the branch type. This patch will return a "none" branch if a kernel address if found to lie in the vsyscall region.Show less

In the Linux kernel, the following vulnerability has been resolved: Input: powermate - fix use-after-free in powermate_config_complete syzbot has found a use-after-free bug [1] in the powermate driver. This happens when the device is disconnected, which leads to a memory free from the powermate_device struct. When an asynchronous control message completes after the kfree and its callback is invoked, the lock does not exist anymore and hence the bug. Use usb_kill_urb() on pm->config to cancel any in-progress requests upon device disconnection. [1] https://syzkaller.appspot.com/bug?extid=0434ac83f907a1dbdd1eShow less

In the Linux kernel, the following vulnerability has been resolved: crypto: sun8i-ss - Fix memory leak of pad It appears there are several failure return paths that don't seem to be free'ing pad. Fix these. Addresses-Coverity: ("Resource leak")Show less

In the Linux kernel, the following vulnerability has been resolved: crypto: sa2ul - Fix memory leak of rxd There are two error return paths that are not freeing rxd and causing memory leaks. Fix these. Addresses-Coverity: ("Resource leak")Show less

In the Linux kernel, the following vulnerability has been resolved: spi: fsl-lpspi: Fix PM reference leak in lpspi_prepare_xfer_hardware() pm_runtime_get_sync will increment pm usage counter even it failed. Forgetting to putting operation will result in reference leak here. Fix it by replacing it with pm_runtime_resume_and_get to keep usage counter balanced.Show less

In the Linux kernel, the following vulnerability has been resolved: memory: renesas-rpc-if: fix possible NULL pointer dereference of resource The platform_get_resource_byname() can return NULL which would be immediately dereferenced by resource_size(). Instead dereference it after validating the resource. Addresses-Coverity: Dereference null return valueShow less

In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: vmbus: Use after free in __vmbus_open() The "open_info" variable is added to the &vmbus_connection.chn_msg_list, but the error handling frees "open_info" without removing it from the list. This will result in a use after free. First remove it from the list, and then free it.Show less

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op When handling op->addr, it is using the buffer "tmpbuf" which has been freed. This will trigger a use-after-free KASAN warning. Let's use temporary variables to store op->addr.val and op->cmd.opcode to fix this issue.Show less

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails The spi controller supports 44-bit address space on AXI in DMA mode, so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping. In addition, if dma_map_single fails, it should return immediately instead of continuing doing the DMA operation which bases on invalid address. This fixes the following crash which occurs in reading a big block from flash: [ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots) [ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped [ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0 [ 123.792536] Mem abort info: [ 123.795313] ESR = 0x96000145 [ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits [ 123.803655] SET = 0, FnV = 0 [ 123.806693] EA = 0, S1PTW = 0 [ 123.809818] Data abort info: [ 123.812683] ISV = 0, ISS = 0x00000145 [ 123.816503] CM = 1, WnR = 1 [ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000 [ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000 [ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMPShow less

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix off by one in hdmi_14_process_transaction() The hdcp_i2c_offsets[] array did not have an entry for HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one read overflow. I added an entry and copied the 0x0 value for the offset from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c. I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX entries. This doesn't change the code, but it's just a belt and suspenders approach to try future proof the code.Show less

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix null pointer dereference in lpfc_prep_els_iocb() It is possible to call lpfc_issue_els_plogi() passing a did for which no matching ndlp is found. A call is then made to lpfc_prep_els_iocb() with a null pointer to a lpfc_nodelist structure resulting in a null pointer dereference. Fix by returning an error status if no valid ndlp is found. Fix up comments regarding ndlp reference counting.Show less