Linux

In the Linux kernel, the following vulnerability has been resolved: ext4: fix memory leak in ext4_fill_super Buffer head references must be released before calling kill_bdev(); otherwise the buffer head (and its page referenced by b_data) will not be freed by kill_bdev, and subsequently that bh will be leaked. If blocksizes differ, sb_set_blocksize() will kill current buffers and page cache by using kill_bdev(). And then super block will be reread again but using correct blocksize this time. sb_set_blocksize() didn't fully free superblock page and buffer head, and being busy, they were not freed and instead leaked. This can easily be reproduced by calling an infinite loop of: systemctl start <ext4_on_lvm>.mount, and systemctl stop <ext4_on_lvm>.mount ... since systemd creates a cgroup for each slice which it mounts, and the bh leak get amplified by a dying memory cgroup that also never gets freed, and memory consumption is much more easily noticed.Show less

In the Linux kernel, the following vulnerability has been resolved: pid: take a reference when initializing `cad_pid` During boot, kernel_init_freeable() initializes `cad_pid` to the init task's struct pid. Later on, we may change `cad_pid` via a sysctl, and when this happens proc_do_cad_pid() will increment the refcount on the new pid via get_pid(), and will decrement the refcount on the old pid via put_pid(). As we never called get_pid() when we initialized `cad_pid`, we decrement a reference we never incremented, can therefore free the init task's struct pid early. As there can be dangling references to the struct pid, we can later encounter a use-after-free (e.g. when delivering signals). This was spotted when fuzzing v5.13-rc3 with Syzkaller, but seems to have been around since the conversion of `cad_pid` to struct pid in commit 9ec52099e4b8 ("[PATCH] replace cad_pid by a struct pid") from the pre-KASAN stone age of v2.6.19. Fix this by getting a reference to the init task's struct pid when we assign it to `cad_pid`. Full KASAN splat below. ================================================================== BUG: KASAN: use-after-free in ns_of_pid include/linux/pid.h:153 [inline] BUG: KASAN: use-after-free in task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509 Read of size 4 at addr ffff23794dda0004 by task syz-executor.0/273 CPU: 1 PID: 273 Comm: syz-executor.0 Not tainted 5.12.0-00001-g9aef892b2d15 #1 Hardware name: linux,dummy-virt (DT) Call trace: ns_of_pid include/linux/pid.h:153 [inline] task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509 do_notify_parent+0x308/0xe60 kernel/signal.c:1950 exit_notify kernel/exit.c:682 [inline] do_exit+0x2334/0x2bd0 kernel/exit.c:845 do_group_exit+0x108/0x2c8 kernel/exit.c:922 get_signal+0x4e4/0x2a88 kernel/signal.c:2781 do_signal arch/arm64/kernel/signal.c:882 [inline] do_notify_resume+0x300/0x970 arch/arm64/kernel/signal.c:936 work_pending+0xc/0x2dc Allocated by task 0: slab_post_alloc_hook+0x50/0x5c0 mm/slab.h:516 slab_alloc_node mm/slub.c:2907 [inline] slab_alloc mm/slub.c:2915 [inline] kmem_cache_alloc+0x1f4/0x4c0 mm/slub.c:2920 alloc_pid+0xdc/0xc00 kernel/pid.c:180 copy_process+0x2794/0x5e18 kernel/fork.c:2129 kernel_clone+0x194/0x13c8 kernel/fork.c:2500 kernel_thread+0xd4/0x110 kernel/fork.c:2552 rest_init+0x44/0x4a0 init/main.c:687 arch_call_rest_init+0x1c/0x28 start_kernel+0x520/0x554 init/main.c:1064 0x0 Freed by task 270: slab_free_hook mm/slub.c:1562 [inline] slab_free_freelist_hook+0x98/0x260 mm/slub.c:1600 slab_free mm/slub.c:3161 [inline] kmem_cache_free+0x224/0x8e0 mm/slub.c:3177 put_pid.part.4+0xe0/0x1a8 kernel/pid.c:114 put_pid+0x30/0x48 kernel/pid.c:109 proc_do_cad_pid+0x190/0x1b0 kernel/sysctl.c:1401 proc_sys_call_handler+0x338/0x4b0 fs/proc/proc_sysctl.c:591 proc_sys_write+0x34/0x48 fs/proc/proc_sysctl.c:617 call_write_iter include/linux/fs.h:1977 [inline] new_sync_write+0x3ac/0x510 fs/read_write.c:518 vfs_write fs/read_write.c:605 [inline] vfs_write+0x9c4/0x1018 fs/read_write.c:585 ksys_write+0x124/0x240 fs/read_write.c:658 __do_sys_write fs/read_write.c:670 [inline] __se_sys_write fs/read_write.c:667 [inline] __arm64_sys_write+0x78/0xb0 fs/read_write.c:667 __invoke_syscall arch/arm64/kernel/syscall.c:37 [inline] invoke_syscall arch/arm64/kernel/syscall.c:49 [inline] el0_svc_common.constprop.1+0x16c/0x388 arch/arm64/kernel/syscall.c:129 do_el0_svc+0xf8/0x150 arch/arm64/kernel/syscall.c:168 el0_svc+0x28/0x38 arch/arm64/kernel/entry-common.c:416 el0_sync_handler+0x134/0x180 arch/arm64/kernel/entry-common.c:432 el0_sync+0x154/0x180 arch/arm64/kernel/entry.S:701 The buggy address belongs to the object at ffff23794dda0000 which belongs to the cache pid of size 224 The buggy address is located 4 bytes inside of 224-byte region [ff ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: ext4: fix bug on in ext4_es_cache_extent as ext4_split_extent_at failed We got follow bug_on when run fsstress with injecting IO fault: [130747.323114] kernel BUG at fs/ext4/extents_status.c:762! [130747.323117] Internal error: Oops - BUG: 0 [#1] SMP ...... [130747.334329] Call trace: [130747.334553] ext4_es_cache_extent+0x150/0x168 [ext4] [130747.334975] ext4_cache_extents+0x64/0xe8 [ext4] [130747.335368] ext4_find_extent+0x300/0x330 [ext4] [130747.335759] ext4_ext_map_blocks+0x74/0x1178 [ext4] [130747.336179] ext4_map_blocks+0x2f4/0x5f0 [ext4] [130747.336567] ext4_mpage_readpages+0x4a8/0x7a8 [ext4] [130747.336995] ext4_readpage+0x54/0x100 [ext4] [130747.337359] generic_file_buffered_read+0x410/0xae8 [130747.337767] generic_file_read_iter+0x114/0x190 [130747.338152] ext4_file_read_iter+0x5c/0x140 [ext4] [130747.338556] __vfs_read+0x11c/0x188 [130747.338851] vfs_read+0x94/0x150 [130747.339110] ksys_read+0x74/0xf0 This patch's modification is according to Jan Kara's suggestion in: https://patchwork.ozlabs.org/project/linux-ext4/patch/20210428085158.3728201-1-yebin10@huawei.com/ "I see. Now I understand your patch. Honestly, seeing how fragile is trying to fix extent tree after split has failed in the middle, I would probably go even further and make sure we fix the tree properly in case of ENOSPC and EDQUOT (those are easily user triggerable). Anything else indicates a HW problem or fs corruption so I'd rather leave the extent tree as is and don't try to fix it (which also means we will not create overlapping extents)."Show less

In the Linux kernel, the following vulnerability has been resolved: ext4: fix memory leak in ext4_mb_init_backend on error path. Fix a memory leak discovered by syzbot when a file system is corrupted with an illegally large s_log_groups_per_flex.Show less

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix data corruption by fallocate When fallocate punches holes out of inode size, if original isize is in the middle of last cluster, then the part from isize to the end of the cluster will be zeroed with buffer write, at that time isize is not yet updated to match the new size, if writeback is kicked in, it will invoke ocfs2_writepage()->block_write_full_page() where the pages out of inode size will be dropped. That will cause file corruption. Fix this by zero out eof blocks when extending the inode size. Running the following command with qemu-image 4.2.1 can get a corrupted coverted image file easily. qemu-img convert -p -t none -T none -f qcow2 $qcow_image \ -O qcow2 -o compat=1.1 $qcow_image.conv The usage of fallocate in qemu is like this, it first punches holes out of inode size, then extend the inode size. fallocate(11, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 2276196352, 65536) = 0 fallocate(11, 0, 2276196352, 65536) = 0 v1: https://www.spinics.net/lists/linux-fsdevel/msg193999.html v2: https://lore.kernel.org/linux-fsdevel/20210525093034.GB4112@quack2.suse.cz/T/Show less

In the Linux kernel, the following vulnerability has been resolved: btrfs: abort in rename_exchange if we fail to insert the second ref Error injection stress uncovered a problem where we'd leave a dangling inode ref if we failed during a rename_exchange. This happens because we insert the inode ref for one side of the rename, and then for the other side. If this second inode ref insert fails we'll leave the first one dangling and leave a corrupt file system behind. Fix this by aborting if we did the insert for the first inode ref.Show less

In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Teardown PV features on boot CPU as well Various PV features (Async PF, PV EOI, steal time) work through memory shared with hypervisor and when we restore from hibernation we must properly teardown all these features to make sure hypervisor doesn't write to stale locations after we jump to the previously hibernated kernel (which can try to place anything there). For secondary CPUs the job is already done by kvm_cpu_down_prepare(), register syscore ops to do the same for boot CPU.Show less

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.Show less

In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Disable kvmclock on all CPUs on shutdown Currenly, we disable kvmclock from machine_shutdown() hook and this only happens for boot CPU. We need to disable it for all CPUs to guard against memory corruption e.g. on restore from hibernate. Note, writing '0' to kvmclock MSR doesn't clear memory location, it just prevents hypervisor from updating the location so for the short while after write and while CPU is still alive, the clock remains usable and correct so we don't need to switch to some other clocksource.Show less

In the Linux kernel, the following vulnerability has been resolved: neighbour: allow NUD_NOARP entries to be forced GCed IFF_POINTOPOINT interfaces use NUD_NOARP entries for IPv6. It's possible to fill up the neighbour table with enough entries that it will overflow for valid connections after that. This behaviour is more prevalent after commit 58956317c8de ("neighbor: Improve garbage collection") is applied, as it prevents removal from entries that are not NUD_FAILED, unless they are more than 5s old.Show less

In the Linux kernel, the following vulnerability has been resolved: mm: cachestat: fix folio read-after-free in cache walk In cachestat, we access the folio from the page cache's xarray to compute its page offset, and check for its dirty and writeback flags. However, we do not hold a reference to the folio before performing these actions, which means the folio can concurrently be released and reused as another folio/page/slab. Get around this altogether by just using xarray's existing machinery for the folio page offsets and dirty/writeback states. This changes behavior for tmpfs files to now always report zeroes in their dirty and writeback counters. This is okay as tmpfs doesn't follow conventional writeback cache behavior: its pages get "cleaned" during swapout, after which they're no longer resident etc.Show less

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix RELEASE_LOCKOWNER The test on so_count in nfsd4_release_lockowner() is nonsense and harmful. Revert to using check_for_locks(), changing that to not sleep. First: harmful. As is documented in the kdoc comment for nfsd4_release_lockowner(), the test on so_count can transiently return a false positive resulting in a return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is clearly a protocol violation and with the Linux NFS client it can cause incorrect behaviour. If RELEASE_LOCKOWNER is sent while some other thread is still processing a LOCK request which failed because, at the time that request was received, the given owner held a conflicting lock, then the nfsd thread processing that LOCK request can hold a reference (conflock) to the lock owner that causes nfsd4_release_lockowner() to return an incorrect error. The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so it knows that the error is impossible. It assumes the lock owner was in fact released so it feels free to use the same lock owner identifier in some later locking request. When it does reuse a lock owner identifier for which a previous RELEASE failed, it will naturally use a lock_seqid of zero. However the server, which didn't release the lock owner, will expect a larger lock_seqid and so will respond with NFS4ERR_BAD_SEQID. So clearly it is harmful to allow a false positive, which testing so_count allows. The test is nonsense because ... well... it doesn't mean anything. so_count is the sum of three different counts. 1/ the set of states listed on so_stateids 2/ the set of active vfs locks owned by any of those states 3/ various transient counts such as for conflicting locks. When it is tested against '2' it is clear that one of these is the transient reference obtained by find_lockowner_str_locked(). It is not clear what the other one is expected to be. In practice, the count is often 2 because there is precisely one state on so_stateids. If there were more, this would fail. In my testing I see two circumstances when RELEASE_LOCKOWNER is called. In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in all the lock states being removed, and so the lockowner being discarded (it is removed when there are no more references which usually happens when the lock state is discarded). When nfsd4_release_lockowner() finds that the lock owner doesn't exist, it returns success. The other case shows an so_count of '2' and precisely one state listed in so_stateid. It appears that the Linux client uses a separate lock owner for each file resulting in one lock state per lock owner, so this test on '2' is safe. For another client it might not be safe. So this patch changes check_for_locks() to use the (newish) find_any_file_locked() so that it doesn't take a reference on the nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With this check is it safe to restore the use of check_for_locks() rather than testing so_count against the mysterious '2'.Show less

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Check mailbox/SMT channel for consistency On reception of a completion interrupt the shared memory area is accessed to retrieve the message header at first and then, if the message sequence number identifies a transaction which is still pending, the related payload is fetched too. When an SCMI command times out the channel ownership remains with the platform until eventually a late reply is received and, as a consequence, any further transmission attempt remains pending, waiting for the channel to be relinquished by the platform. Once that late reply is received the channel ownership is given back to the agent and any pending request is then allowed to proceed and overwrite the SMT area of the just delivered late reply; then the wait for the reply to the new request starts. It has been observed that the spurious IRQ related to the late reply can be wrongly associated with the freshly enqueued request: when that happens the SCMI stack in-flight lookup procedure is fooled by the fact that the message header now present in the SMT area is related to the new pending transaction, even though the real reply has still to arrive. This race-condition on the A2P channel can be detected by looking at the channel status bits: a genuine reply from the platform will have set the channel free bit before triggering the completion IRQ. Add a consistency check to validate such condition in the A2P ISR.Show less

In the Linux kernel, the following vulnerability has been resolved: s390/vfio-ap: always filter entire AP matrix The vfio_ap_mdev_filter_matrix function is called whenever a new adapter or domain is assigned to the mdev. The purpose of the function is to update the guest's AP configuration by filtering the matrix of adapters and domains assigned to the mdev. When an adapter or domain is assigned, only the APQNs associated with the APID of the new adapter or APQI of the new domain are inspected. If an APQN does not reference a queue device bound to the vfio_ap device driver, then it's APID will be filtered from the mdev's matrix when updating the guest's AP configuration. Inspecting only the APID of the new adapter or APQI of the new domain will result in passing AP queues through to a guest that are not bound to the vfio_ap device driver under certain circumstances. Consider the following: guest's AP configuration (all also assigned to the mdev's matrix): 14.0004 14.0005 14.0006 16.0004 16.0005 16.0006 unassign domain 4 unbind queue 16.0005 assign domain 4 When domain 4 is re-assigned, since only domain 4 will be inspected, the APQNs that will be examined will be: 14.0004 16.0004 Since both of those APQNs reference queue devices that are bound to the vfio_ap device driver, nothing will get filtered from the mdev's matrix when updating the guest's AP configuration. Consequently, queue 16.0005 will get passed through despite not being bound to the driver. This violates the linux device model requirement that a guest shall only be given access to devices bound to the device driver facilitating their pass-through. To resolve this problem, every adapter and domain assigned to the mdev will be inspected when filtering the mdev's matrix.Show less

In the Linux kernel, the following vulnerability has been resolved: arm64/sme: Always exit sme_alloc() early with existing storage When sme_alloc() is called with existing storage and we are not flushing we will always allocate new storage, both leaking the existing storage and corrupting the state. Fix this by separating the checks for flushing and for existing storage as we do for SVE. Callers that reallocate (eg, due to changing the vector length) should call sme_free() themselves.Show less

In the Linux kernel, the following vulnerability has been resolved: fs/proc/task_mmu: move mmu notification mechanism inside mm lock Move mmu notification mechanism inside mm lock to prevent race condition in other components which depend on it. The notifier will invalidate memory range. Depending upon the number of iterations, different memory ranges would be invalidated. The following warning would be removed by this patch: WARNING: CPU: 0 PID: 5067 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:734 kvm_mmu_notifier_change_pte+0x860/0x960 arch/x86/kvm/../../../virt/kvm/kvm_main.c:734 There is no behavioural and performance change with this patch when there is no component registered with the mmu notifier. [akpm@linux-foundation.org: narrow the scope of `range', per Sean]Show less

In the Linux kernel, the following vulnerability has been resolved: btrfs: scrub: avoid use-after-free when chunk length is not 64K aligned [BUG] There is a bug report that, on a ext4-converted btrfs, scrub leads to various problems, including: - "unable to find chunk map" errors BTRFS info (device vdb): scrub: started on devid 1 BTRFS critical (device vdb): unable to find chunk map for logical 2214744064 length 4096 BTRFS critical (device vdb): unable to find chunk map for logical 2214744064 length 45056 This would lead to unrepariable errors. - Use-after-free KASAN reports: ================================================================== BUG: KASAN: slab-use-after-free in __blk_rq_map_sg+0x18f/0x7c0 Read of size 8 at addr ffff8881013c9040 by task btrfs/909 CPU: 0 PID: 909 Comm: btrfs Not tainted 6.7.0-x64v3-dbg #11 c50636e9419a8354555555245df535e380563b2b Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 2023.11-2 12/24/2023 Call Trace: <TASK> dump_stack_lvl+0x43/0x60 print_report+0xcf/0x640 kasan_report+0xa6/0xd0 __blk_rq_map_sg+0x18f/0x7c0 virtblk_prep_rq.isra.0+0x215/0x6a0 [virtio_blk 19a65eeee9ae6fcf02edfad39bb9ddee07dcdaff] virtio_queue_rqs+0xc4/0x310 [virtio_blk 19a65eeee9ae6fcf02edfad39bb9ddee07dcdaff] blk_mq_flush_plug_list.part.0+0x780/0x860 __blk_flush_plug+0x1ba/0x220 blk_finish_plug+0x3b/0x60 submit_initial_group_read+0x10a/0x290 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] flush_scrub_stripes+0x38e/0x430 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] scrub_stripe+0x82a/0xae0 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] scrub_chunk+0x178/0x200 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] scrub_enumerate_chunks+0x4bc/0xa30 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] btrfs_scrub_dev+0x398/0x810 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] btrfs_ioctl+0x4b9/0x3020 [btrfs e57987a360bed82fe8756dcd3e0de5406ccfe965] __x64_sys_ioctl+0xbd/0x100 do_syscall_64+0x5d/0xe0 entry_SYSCALL_64_after_hwframe+0x63/0x6b RIP: 0033:0x7f47e5e0952b - Crash, mostly due to above use-after-free [CAUSE] The converted fs has the following data chunk layout: item 2 key (FIRST_CHUNK_TREE CHUNK_ITEM 2214658048) itemoff 16025 itemsize 80 length 86016 owner 2 stripe_len 65536 type DATA|single For above logical bytenr 2214744064, it's at the chunk end (2214658048 + 86016 = 2214744064). This means btrfs_submit_bio() would split the bio, and trigger endio function for both of the two halves. However scrub_submit_initial_read() would only expect the endio function to be called once, not any more. This means the first endio function would already free the bbio::bio, leaving the bvec freed, thus the 2nd endio call would lead to use-after-free. [FIX] - Make sure scrub_read_endio() only updates bits in its range Since we may read less than 64K at the end of the chunk, we should not touch the bits beyond chunk boundary. - Make sure scrub_submit_initial_read() only to read the chunk range This is done by calculating the real number of sectors we need to read, and add sector-by-sector to the bio. Thankfully the scrub read repair path won't need extra fixes: - scrub_stripe_submit_repair_read() With above fixes, we won't update error bit for range beyond chunk, thus scrub_stripe_submit_repair_read() should never submit any read beyond the chunk.Show less

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix illegal rmb_desc access in SMC-D connection dump A crash was found when dumping SMC-D connections. It can be reproduced by following steps: - run nginx/wrk test: smc_run nginx smc_run wrk -t 16 -c 1000 -d <duration> -H 'Connection: Close' <URL> - continuously dump SMC-D connections in parallel: watch -n 1 'smcss -D' BUG: kernel NULL pointer dereference, address: 0000000000000030 CPU: 2 PID: 7204 Comm: smcss Kdump: loaded Tainted: G E 6.7.0+ #55 RIP: 0010:__smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag] Call Trace: <TASK> ? __die+0x24/0x70 ? page_fault_oops+0x66/0x150 ? exc_page_fault+0x69/0x140 ? asm_exc_page_fault+0x26/0x30 ? __smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag] ? __kmalloc_node_track_caller+0x35d/0x430 ? __alloc_skb+0x77/0x170 smc_diag_dump_proto+0xd0/0xf0 [smc_diag] smc_diag_dump+0x26/0x60 [smc_diag] netlink_dump+0x19f/0x320 __netlink_dump_start+0x1dc/0x300 smc_diag_handler_dump+0x6a/0x80 [smc_diag] ? __pfx_smc_diag_dump+0x10/0x10 [smc_diag] sock_diag_rcv_msg+0x121/0x140 ? __pfx_sock_diag_rcv_msg+0x10/0x10 netlink_rcv_skb+0x5a/0x110 sock_diag_rcv+0x28/0x40 netlink_unicast+0x22a/0x330 netlink_sendmsg+0x1f8/0x420 __sock_sendmsg+0xb0/0xc0 ____sys_sendmsg+0x24e/0x300 ? copy_msghdr_from_user+0x62/0x80 ___sys_sendmsg+0x7c/0xd0 ? __do_fault+0x34/0x160 ? do_read_fault+0x5f/0x100 ? do_fault+0xb0/0x110 ? __handle_mm_fault+0x2b0/0x6c0 __sys_sendmsg+0x4d/0x80 do_syscall_64+0x69/0x180 entry_SYSCALL_64_after_hwframe+0x6e/0x76 It is possible that the connection is in process of being established when we dump it. Assumed that the connection has been registered in a link group by smc_conn_create() but the rmb_desc has not yet been initialized by smc_buf_create(), thus causing the illegal access to conn->rmb_desc. So fix it by checking before dump.Show less

In the Linux kernel, the following vulnerability has been resolved: tcp: make sure init the accept_queue's spinlocks once When I run syz's reproduction C program locally, it causes the following issue: pvqspinlock: lock 0xffff9d181cd5c660 has corrupted value 0x0! WARNING: CPU: 19 PID: 21160 at __pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508) Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:__pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508) Code: 73 56 3a ff 90 c3 cc cc cc cc 8b 05 bb 1f 48 01 85 c0 74 05 c3 cc cc cc cc 8b 17 48 89 fe 48 c7 c7 30 20 ce 8f e8 ad 56 42 ff <0f> 0b c3 cc cc cc cc 0f 0b 0f 1f 40 00 90 90 90 90 90 90 90 90 90 RSP: 0018:ffffa8d200604cb8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9d1ef60e0908 RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff9d1ef60e0900 RBP: ffff9d181cd5c280 R08: 0000000000000000 R09: 00000000ffff7fff R10: ffffa8d200604b68 R11: ffffffff907dcdc8 R12: 0000000000000000 R13: ffff9d181cd5c660 R14: ffff9d1813a3f330 R15: 0000000000001000 FS: 00007fa110184640(0000) GS:ffff9d1ef60c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000000 CR3: 000000011f65e000 CR4: 00000000000006f0 Call Trace: <IRQ> _raw_spin_unlock (kernel/locking/spinlock.c:186) inet_csk_reqsk_queue_add (net/ipv4/inet_connection_sock.c:1321) inet_csk_complete_hashdance (net/ipv4/inet_connection_sock.c:1358) tcp_check_req (net/ipv4/tcp_minisocks.c:868) tcp_v4_rcv (net/ipv4/tcp_ipv4.c:2260) ip_protocol_deliver_rcu (net/ipv4/ip_input.c:205) ip_local_deliver_finish (net/ipv4/ip_input.c:234) __netif_receive_skb_one_core (net/core/dev.c:5529) process_backlog (./include/linux/rcupdate.h:779) __napi_poll (net/core/dev.c:6533) net_rx_action (net/core/dev.c:6604) __do_softirq (./arch/x86/include/asm/jump_label.h:27) do_softirq (kernel/softirq.c:454 kernel/softirq.c:441) </IRQ> <TASK> __local_bh_enable_ip (kernel/softirq.c:381) __dev_queue_xmit (net/core/dev.c:4374) ip_finish_output2 (./include/net/neighbour.h:540 net/ipv4/ip_output.c:235) __ip_queue_xmit (net/ipv4/ip_output.c:535) __tcp_transmit_skb (net/ipv4/tcp_output.c:1462) tcp_rcv_synsent_state_process (net/ipv4/tcp_input.c:6469) tcp_rcv_state_process (net/ipv4/tcp_input.c:6657) tcp_v4_do_rcv (net/ipv4/tcp_ipv4.c:1929) __release_sock (./include/net/sock.h:1121 net/core/sock.c:2968) release_sock (net/core/sock.c:3536) inet_wait_for_connect (net/ipv4/af_inet.c:609) __inet_stream_connect (net/ipv4/af_inet.c:702) inet_stream_connect (net/ipv4/af_inet.c:748) __sys_connect (./include/linux/file.h:45 net/socket.c:2064) __x64_sys_connect (net/socket.c:2073 net/socket.c:2070 net/socket.c:2070) do_syscall_64 (arch/x86/entry/common.c:51 arch/x86/entry/common.c:82) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129) RIP: 0033:0x7fa10ff05a3d Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ab a3 0e 00 f7 d8 64 89 01 48 RSP: 002b:00007fa110183de8 EFLAGS: 00000202 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000020000054 RCX: 00007fa10ff05a3d RDX: 000000000000001c RSI: 0000000020000040 RDI: 0000000000000003 RBP: 00007fa110183e20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000202 R12: 00007fa110184640 R13: 0000000000000000 R14: 00007fa10fe8b060 R15: 00007fff73e23b20 </TASK> The issue triggering process is analyzed as follows: Thread A Thread B tcp_v4_rcv //receive ack TCP packet inet_shutdown tcp_check_req tcp_disconnect //disconnect sock ... tcp_set_state(sk, TCP_CLOSE) inet_csk_complete_hashdance ... inet_csk_reqsk_queue_add ---truncated---Show less