Dlink

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device has a custom telnet daemon as a part of the busybox and retrieves the password from the shadow file using the function getspnam at address 0x00053894. Then performs a crypt operation on the password retrieved from the user at address 0x000538E0 and performs a strcmp at address 0x00053908 to check if the password is correct or incorrect. However, the /etc/shadow file is a part of CRAM-FS filesystem which means that the user cannot change the password and hence a hardcoded hash in /etc/shadow is used to match the credentials provided by the user. This is a salted hash of the string "admin" and hence it acts as a password to the device which cannot be changed as the whole filesystem is read only.Show less

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device runs a custom daemon on UDP port 5978 which is called "dldps2121" and listens for broadcast packets sent on 255.255.255.255. This daemon handles custom D-Link UDP based protocol that allows D-Link mobile applications and desktop applications to discover D-Link devices on the local network. The binary processes the received UDP packets sent from any device in "main" function. One path in the function traverses towards a block of code that handles commands to be executed on the device. The custom protocol created by D-Link follows the following pattern: Packetlen, Type of packet; M=MAC address of device or broadcast; D=Device Type;C=base64 encoded command string;test=1111. If a packet is received with the packet type being "S" or 0x53 then the string passed in the "C" parameter is base64 decoded and then executed by passing into a System API. We can see at address 0x00009B44 that the string received in packet type subtracts 0x31 or "1" from the packet type and is compared against 0x22 or "double quotes". If that is the case, then the packet is sent towards the block of code that executes a command. Then the value stored in "C" parameter is extracted at address 0x0000A1B0. Finally, the string received is base 64 decoded and passed on to the system API at address 0x0000A2A8 as shown below. The same form of communication can be initiated by any process including an attacker process on the mobile phone or the desktop and this allows a third-party application on the device to execute commands on the device without any authentication by sending just 1 UDP packet with custom base64 encoding.Show less

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The device has a custom binary called mp4ts under the /var/www/video folder. It seems that this binary dumps the HTTP VERB in the system logs. As a part of doing that it retrieves the HTTP VERB sent by the user and uses a vulnerable sprintf function at address 0x0000C3D4 in the function sub_C210 to copy the value into a string and then into a log file. Since there is no bounds check being performed on the environment variable at address 0x0000C360 this results in a stack overflow and overwrites the PC register allowing an attacker to execute buffer overflow or even a command injection attack.Show less

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The binary orthrus in /sbin folder of the device handles all the UPnP connections received by the device. It seems that the binary performs a sprintf operation at address 0x0000A3E4 with the value in the command line parameter "-f" and stores it on the stack. Since there is no length check, this results in corrupting the registers for the function sub_A098 which results in memory corruption.Show less

An issue was discovered on D-Link DCS-1100 and DCS-1130 devices. The binary rtspd in /sbin folder of the device handles all the rtsp connections received by the device. It seems that the binary performs a memcpy operation at address 0x00011E34 with the value sent in the "Authorization: Basic" RTSP header and stores it on the stack. The number of bytes to be copied are calculated based on the length of the string sent in the RTSP header by the client. As a result, memcpy copies more data then it can hold on stack and this results in corrupting the registers for the caller function sub_F6CC which results in memory corruption. The severity of this attack is enlarged by the fact that the same value is then copied on the stack in the function 0x00011378 and this allows to overflow the buffer allocated and thus control the PC register which will result in arbitrary code execution on the device.Show less

An issue was discovered on D-Link DCS-1130 devices. The device requires that a user logging to the device to provide a username and password. However, the device does not enforce the same restriction on a specific URL thereby allowing any attacker in possession of that to view the live video feed. The severity of this attack is enlarged by the fact that there more than 100,000 D-Link devices out there.Show less

An issue was discovered on D-Link DCS-1130 devices. The device provides a crossdomain.xml file with no restrictions on who can access the webserver. This allows an hosted flash file on any domain to make calls to the device's webserver and pull any information that is stored on the device. In this case, user's credentials are stored in clear text on the device and can be pulled easily. It also seems that the device does not implement any cross-site scripting forgery protection mechanism which allows an attacker to trick a user who is logged in to the web management interface into executing a cross-site flashing attack on the user's browser and execute any action on the device provided by the web management interface which steals the credentials from tools_admin.cgi file's response and displays it inside a Textfield.Show less

An issue was discovered on D-Link DCS-1130 and DCS-1100 devices. The binary rtspd in /sbin folder of the device handles all the rtsp connections received by the device. It seems that the binary loads at address 0x00012CF4 a flag called "Authenticate" that indicates whether a user should be authenticated or not before allowing access to the video feed. By default, the value for this flag is zero and can be set/unset using the HTTP interface and network settings tab as shown below. The device requires that a user logging to the HTTP management interface of the device to provide a valid username and password. However, the device does not enforce the same restriction by default on RTSP URL due to the checkbox unchecked by default, thereby allowing any attacker in possession of external IP address of the camera to view the live video feed. The severity of this attack is enlarged by the fact that there more than 100,000 D-Link devices out there.Show less

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the POST parameters passed in this request (to test if email credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The library "libmailutils.so" is the one that has the vulnerable function "sub_1FC4" that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows an ARM little endian format. The function sub_1FC4 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "receiver1" is extracted in function "sub_15AC" which is then passed to the vulnerable system API call. The vulnerable library function is accessed in "cgibox" binary at address 0x00023BCC which calls the "Send_mail" function in "libmailutils.so" binary as shown below which results in the vulnerable POST parameter being passed to the library which results in the command injection issue.Show less

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of changing the administrative password for the web management interface. It seems that the device does not implement any cross-site request forgery protection mechanism which allows an attacker to trick a user who is logged in to the web management interface to change the user's password.Show less

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the POST parameters passed in this request (to test if email credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The library "libmailutils.so" is the one that has the vulnerable function "sub_1FC4" that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows an ARM little endian format. The function sub_1FC4 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "receiver1" is extracted in function "sub_15AC" which is then passed to the vulnerable system API call. The vulnerable library function is accessed in "cgibox" binary at address 0x0008F598 which calls the "mailLoginTest" function in "libmailutils.so" binary as shown below which results in the vulnerable POST parameter being passed to the library which results in the command injection issue.Show less

An issue was discovered on D-Link DCS-1130 devices. The device provides a user with the capability of setting a SMB folder for the video clippings recorded by the device. It seems that the GET parameters passed in this request (to test if SMB credentials and hostname sent to the device work properly) result in being passed as commands to a "system" API in the function and thus result in command injection on the device. If the firmware version is dissected using binwalk tool, we obtain a cramfs-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "cgibox" is the one that has the vulnerable function "sub_7EAFC" that receives the values sent by the GET request. If we open this binary in IDA-pro we will notice that this follows a ARM little endian format. The function sub_7EAFC in IDA pro is identified to be receiving the values sent in the GET request and the value set in GET parameter "user" is extracted in function sub_7E49C which is then passed to the vulnerable system API call.Show less

An issue was discovered on D-Link DIR-823G devices with firmware 1.02B03. There is a command injection in HNAP1 (exploitable with Authentication) via shell metacharacters in the IPAddress or Gateway field to SetStaticRouteSettings.Show less

An issue was discovered in soap.cgi?service=WANIPConn1 on D-Link DIR-845 before v1.02b03, DIR-600 before v2.17b01, DIR-645 before v1.04b11, DIR-300 rev. B, and DIR-865 devices. There is Command Injection via shell metacharacters in the NewInternalClient, NewExternalPort, or NewInternalPort element of a SOAP POST request.Show less

In the /HNAP1/SetQoSSettings message, the uplink parameter is vulnerable, and the vulnerability affects D-Link DIR-822 Rev.B 202KRb06 and DIR-822 Rev.C 3.10B06 devices. In the SetQoSSettings.php source code, the uplink parameter is saved in the /bwc/entry:1/bandwidth and /bwc/entry:2/bandwidth internal configuration memory without any regex checking. And in the bwc_tc_spq_start, bwc_tc_wfq_start, and bwc_tc_adb_start functions of the bwcsvcs.php source code, the data in /bwc/entry:1/bandwidth and /bwc/entry:2/bandwidth is used with the tc command without any regex checking. A vulnerable /HNAP1/SetQoSSettings XML message could have shell metacharacters in the uplink element such as the `telnetd` string.Show less

D-Link DIR-822 Rev.B 202KRb06, DIR-822 Rev.C 3.10B06, DIR-860L Rev.B 2.03.B03, DIR-868L Rev.B 2.05B02, DIR-880L Rev.A 1.20B01_01_i3se_BETA, and DIR-890L Rev.A 1.21B02_BETA devices mishandle IsAccessPoint in /HNAP1/SetAccessPointMode. In the SetAccessPointMode.php source code, the IsAccessPoint parameter is saved in the ShellPath script file without any regex checking. After the script file is executed, the command injection occurs. A vulnerable /HNAP1/SetAccessPointMode XML message could have shell metacharacters in the IsAccessPoint element such as the `telnetd` string.Show less

The D-Link DCS series of Wi-Fi cameras contains a stack-based buffer overflow in alphapd, the camera's web server. The overflow allows a remotely authenticated attacker to execute arbitrary code by providing a long string in the WEPEncryption parameter when requesting wireless.htm. Vulnerable devices include DCS-5009L (1.08.11 and below), DCS-5010L (1.14.09 and below), DCS-5020L (1.15.12 and below), DCS-5025L (1.03.07 and below), DCS-5030L (1.04.10 and below), DCS-930L (2.16.01 and below), DCS-931L (1.14.11 and below), DCS-932L (2.17.01 and below), DCS-933L (1.14.11 and below), and DCS-934L (1.05.04 and below).Show less