Linux Kernel

In the Linux kernel, the following vulnerability has been resolved: tty: fix deadlock caused by calling printk() under tty_port->lock pty_write() invokes kmalloc() which may invoke a normal printk() to print failure message. This can cause a deadlock in the scenario reported by syz-bot below: CPU0 CPU1 CPU2 ---- ---- ---- lock(console_owner); lock(&port_lock_key); lock(&port->lock); lock(&port_lock_key); lock(&port->lock); lock(console_owner); As commit dbdda842fe96 ("printk: Add console owner and waiter logic to load balance console writes") said, such deadlock can be prevented by using printk_deferred() in kmalloc() (which is invoked in the section guarded by the port->lock). But there are too many printk() on the kmalloc() path, and kmalloc() can be called from anywhere, so changing printk() to printk_deferred() is too complicated and inelegant. Therefore, this patch chooses to specify __GFP_NOWARN to kmalloc(), so that printk() will not be called, and this deadlock problem can be avoided. Syzbot reported the following lockdep error: ====================================================== WARNING: possible circular locking dependency detected 5.4.143-00237-g08ccc19a-dirty #10 Not tainted ------------------------------------------------------ syz-executor.4/29420 is trying to acquire lock: ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: console_trylock_spinning kernel/printk/printk.c:1752 [inline] ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: vprintk_emit+0x2ca/0x470 kernel/printk/printk.c:2023 but task is already holding lock: ffff8880119c9158 (&port->lock){-.-.}-{2:2}, at: pty_write+0xf4/0x1f0 drivers/tty/pty.c:120 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&port->lock){-.-.}-{2:2}: __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159 tty_port_tty_get drivers/tty/tty_port.c:288 [inline] <-- lock(&port->lock); tty_port_default_wakeup+0x1d/0xb0 drivers/tty/tty_port.c:47 serial8250_tx_chars+0x530/0xa80 drivers/tty/serial/8250/8250_port.c:1767 serial8250_handle_irq.part.0+0x31f/0x3d0 drivers/tty/serial/8250/8250_port.c:1854 serial8250_handle_irq drivers/tty/serial/8250/8250_port.c:1827 [inline] <-- lock(&port_lock_key); serial8250_default_handle_irq+0xb2/0x220 drivers/tty/serial/8250/8250_port.c:1870 serial8250_interrupt+0xfd/0x200 drivers/tty/serial/8250/8250_core.c:126 __handle_irq_event_percpu+0x109/0xa50 kernel/irq/handle.c:156 [...] -> #1 (&port_lock_key){-.-.}-{2:2}: __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159 serial8250_console_write+0x184/0xa40 drivers/tty/serial/8250/8250_port.c:3198 <-- lock(&port_lock_key); call_console_drivers kernel/printk/printk.c:1819 [inline] console_unlock+0x8cb/0xd00 kernel/printk/printk.c:2504 vprintk_emit+0x1b5/0x470 kernel/printk/printk.c:2024 <-- lock(console_owner); vprintk_func+0x8d/0x250 kernel/printk/printk_safe.c:394 printk+0xba/0xed kernel/printk/printk.c:2084 register_console+0x8b3/0xc10 kernel/printk/printk.c:2829 univ8250_console_init+0x3a/0x46 drivers/tty/serial/8250/8250_core.c:681 console_init+0x49d/0x6d3 kernel/printk/printk.c:2915 start_kernel+0x5e9/0x879 init/main.c:713 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241 -> #0 (console_owner){....}-{0:0}: [...] lock_acquire+0x127/0x340 kernel/locking/lockdep.c:4734 console_trylock_spinning kernel/printk/printk.c:1773 ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/rtas: Keep MSR[RI] set when calling RTAS RTAS runs in real mode (MSR[DR] and MSR[IR] unset) and in 32-bit big endian mode (MSR[SF,LE] unset). The change in MSR is done in enter_rtas() in a relatively complex way, since the MSR value could be hardcoded. Furthermore, a panic has been reported when hitting the watchdog interrupt while running in RTAS, this leads to the following stack trace: watchdog: CPU 24 Hard LOCKUP watchdog: CPU 24 TB:997512652051031, last heartbeat TB:997504470175378 (15980ms ago) ... Supported: No, Unreleased kernel CPU: 24 PID: 87504 Comm: drmgr Kdump: loaded Tainted: G E X 5.14.21-150400.71.1.bz196362_2-default #1 SLE15-SP4 (unreleased) 0d821077ef4faa8dfaf370efb5fdca1fa35f4e2c NIP: 000000001fb41050 LR: 000000001fb4104c CTR: 0000000000000000 REGS: c00000000fc33d60 TRAP: 0100 Tainted: G E X (5.14.21-150400.71.1.bz196362_2-default) MSR: 8000000002981000 <SF,VEC,VSX,ME> CR: 48800002 XER: 20040020 CFAR: 000000000000011c IRQMASK: 1 GPR00: 0000000000000003 ffffffffffffffff 0000000000000001 00000000000050dc GPR04: 000000001ffb6100 0000000000000020 0000000000000001 000000001fb09010 GPR08: 0000000020000000 0000000000000000 0000000000000000 0000000000000000 GPR12: 80040000072a40a8 c00000000ff8b680 0000000000000007 0000000000000034 GPR16: 000000001fbf6e94 000000001fbf6d84 000000001fbd1db0 000000001fb3f008 GPR20: 000000001fb41018 ffffffffffffffff 000000000000017f fffffffffffff68f GPR24: 000000001fb18fe8 000000001fb3e000 000000001fb1adc0 000000001fb1cf40 GPR28: 000000001fb26000 000000001fb460f0 000000001fb17f18 000000001fb17000 NIP [000000001fb41050] 0x1fb41050 LR [000000001fb4104c] 0x1fb4104c Call Trace: Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX Oops: Unrecoverable System Reset, sig: 6 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries ... Supported: No, Unreleased kernel CPU: 24 PID: 87504 Comm: drmgr Kdump: loaded Tainted: G E X 5.14.21-150400.71.1.bz196362_2-default #1 SLE15-SP4 (unreleased) 0d821077ef4faa8dfaf370efb5fdca1fa35f4e2c NIP: 000000001fb41050 LR: 000000001fb4104c CTR: 0000000000000000 REGS: c00000000fc33d60 TRAP: 0100 Tainted: G E X (5.14.21-150400.71.1.bz196362_2-default) MSR: 8000000002981000 <SF,VEC,VSX,ME> CR: 48800002 XER: 20040020 CFAR: 000000000000011c IRQMASK: 1 GPR00: 0000000000000003 ffffffffffffffff 0000000000000001 00000000000050dc GPR04: 000000001ffb6100 0000000000000020 0000000000000001 000000001fb09010 GPR08: 0000000020000000 0000000000000000 0000000000000000 0000000000000000 GPR12: 80040000072a40a8 c00000000ff8b680 0000000000000007 0000000000000034 GPR16: 000000001fbf6e94 000000001fbf6d84 000000001fbd1db0 000000001fb3f008 GPR20: 000000001fb41018 ffffffffffffffff 000000000000017f fffffffffffff68f GPR24: 000000001fb18fe8 000000001fb3e000 000000001fb1adc0 000000001fb1cf40 GPR28: 000000001fb26000 000000001fb460f0 000000001fb17f18 000000001fb17000 NIP [000000001fb41050] 0x1fb41050 LR [000000001fb4104c] 0x1fb4104c Call Trace: Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace 3ddec07f638c34a2 ]--- This happens because MSR[RI] is unset when entering RTAS but there is no valid reason to not set it here. RTAS is expected to be called with MSR[RI] as specified in PAPR+ section "7.2.1 Machine State": R1–7.2.1–9. If called with MSR[RI] equal to 1, then RTAS must protect its own critical regions from recursion by setting the MSR[RI] bit to 0 when in the critical regions. Fixing this by reviewing the way MSR is compute before calling RTAS. Now a hardcoded value meaning real ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/fsl_rio: Fix refcount leak in fsl_rio_setup of_parse_phandle() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak.Show less

In the Linux kernel, the following vulnerability has been resolved: Input: sparcspkr - fix refcount leak in bbc_beep_probe of_find_node_by_path() calls of_find_node_opts_by_path(), which returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/xive: Fix refcount leak in xive_spapr_init of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/papr_scm: Fix leaking nvdimm_events_map elements Right now 'char *' elements allocated for individual 'stat_id' in 'papr_scm_priv.nvdimm_events_map[]' during papr_scm_pmu_check_events(), get leaked in papr_scm_remove() and papr_scm_pmu_register(), papr_scm_pmu_check_events() error paths. Also individual 'stat_id' arent NULL terminated 'char *' instead they are fixed 8-byte sized identifiers. However papr_scm_pmu_register() assumes it to be a NULL terminated 'char *' and at other places it assumes it to be a 'papr_scm_perf_stat.stat_id' sized string which is 8-byes in size. Fix this by allocating the memory for papr_scm_priv.nvdimm_events_map to also include space for 'stat_id' entries. This is possible since number of available events/stat_ids are known upfront. This saves some memory and one extra level of indirection from 'nvdimm_events_map' to 'stat_id'. Also rest of the code can continue to call 'kfree(papr_scm_priv.nvdimm_events_map)' without needing to iterate over the array and free up individual elements.Show less

In the Linux kernel, the following vulnerability has been resolved: mfd: davinci_voicecodec: Fix possible null-ptr-deref davinci_vc_probe() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref. And use devm_platform_get_and_ioremap_resource() to simplify code.Show less

In the Linux kernel, the following vulnerability has been resolved: PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store() The sysfs sriov_numvfs_store() path acquires the device lock before the config space access lock: sriov_numvfs_store device_lock # A (1) acquire device lock sriov_configure vfio_pci_sriov_configure # (for example) vfio_pci_core_sriov_configure pci_disable_sriov sriov_disable pci_cfg_access_lock pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0 Previously, pci_dev_lock() acquired the config space access lock before the device lock: pci_dev_lock pci_cfg_access_lock dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1 device_lock # A (3) wait for device lock Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may deadlock with sriov_numvfs_store() if the operations occur in the sequence (1) (2) (3) (4). Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires the device lock before the config space access lock, the same as the sriov_numvfs_store() path. [bhelgaas: combined and adapted commit log from Jay Zhou's independent subsequent posting: https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com]Show less

In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Prevent use of lock before it is initialized If there is a failure during probe of hfi1 before the sdma_map_lock is initialized, the call to hfi1_free_devdata() will attempt to use a lock that has not been initialized. If the locking correctness validator is on then an INFO message and stack trace resembling the following may be seen: INFO: trying to register non-static key. The code is fine but needs lockdep annotation, or maybe you didn't initialize this object before use? turning off the locking correctness validator. Call Trace: register_lock_class+0x11b/0x880 __lock_acquire+0xf3/0x7930 lock_acquire+0xff/0x2d0 _raw_spin_lock_irq+0x46/0x60 sdma_clean+0x42a/0x660 [hfi1] hfi1_free_devdata+0x3a7/0x420 [hfi1] init_one+0x867/0x11a0 [hfi1] pci_device_probe+0x40e/0x8d0 The use of sdma_map_lock in sdma_clean() is for freeing the sdma_map memory, and sdma_map is not allocated/initialized until after sdma_map_lock has been initialized. This code only needs to be run if sdma_map is not NULL, and so checking for that condition will avoid trying to use the lock before it is initialized.Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/xics: fix refcount leak in icp_opal_init() The of_find_compatible_node() function returns a node pointer with refcount incremented, use of_node_put() on it when done.Show less

In the Linux kernel, the following vulnerability has been resolved: powerpc/iommu: Add missing of_node_put in iommu_init_early_dart The device_node pointer is returned by of_find_compatible_node with refcount incremented. We should use of_node_put() to avoid the refcount leak.Show less

In the Linux kernel, the following vulnerability has been resolved: Input: gpio-keys - cancel delayed work only in case of GPIO gpio_keys module can either accept gpios or interrupts. The module initializes delayed work in case of gpios only and is only used if debounce timer is not used, so make sure cancel_delayed_work_sync() is called only when its gpio-backed and debounce_use_hrtimer is false. This fixes the issue seen below when the gpio_keys module is unloaded and an interrupt pin is used instead of GPIO: [ 360.297569] ------------[ cut here ]------------ [ 360.302303] WARNING: CPU: 0 PID: 237 at kernel/workqueue.c:3066 __flush_work+0x414/0x470 [ 360.310531] Modules linked in: gpio_keys(-) [ 360.314797] CPU: 0 PID: 237 Comm: rmmod Not tainted 5.18.0-rc5-arm64-renesas-00116-g73636105874d-dirty #166 [ 360.324662] Hardware name: Renesas SMARC EVK based on r9a07g054l2 (DT) [ 360.331270] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 360.338318] pc : __flush_work+0x414/0x470 [ 360.342385] lr : __cancel_work_timer+0x140/0x1b0 [ 360.347065] sp : ffff80000a7fba00 [ 360.350423] x29: ffff80000a7fba00 x28: ffff000012b9c5c0 x27: 0000000000000000 [ 360.357664] x26: ffff80000a7fbb80 x25: ffff80000954d0a8 x24: 0000000000000001 [ 360.364904] x23: ffff800009757000 x22: 0000000000000000 x21: ffff80000919b000 [ 360.372143] x20: ffff00000f5974e0 x19: ffff00000f5974e0 x18: ffff8000097fcf48 [ 360.379382] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000053f40 [ 360.386622] x14: ffff800009850e88 x13: 0000000000000002 x12: 000000000000a60c [ 360.393861] x11: 000000000000a610 x10: 0000000000000000 x9 : 0000000000000008 [ 360.401100] x8 : 0101010101010101 x7 : 00000000a473c394 x6 : 0080808080808080 [ 360.408339] x5 : 0000000000000001 x4 : 0000000000000000 x3 : ffff80000919b458 [ 360.415578] x2 : ffff8000097577f0 x1 : 0000000000000001 x0 : 0000000000000000 [ 360.422818] Call trace: [ 360.425299] __flush_work+0x414/0x470 [ 360.429012] __cancel_work_timer+0x140/0x1b0 [ 360.433340] cancel_delayed_work_sync+0x10/0x18 [ 360.437931] gpio_keys_quiesce_key+0x28/0x58 [gpio_keys] [ 360.443327] devm_action_release+0x10/0x18 [ 360.447481] release_nodes+0x8c/0x1a0 [ 360.451194] devres_release_all+0x90/0x100 [ 360.455346] device_unbind_cleanup+0x14/0x60 [ 360.459677] device_release_driver_internal+0xe8/0x168 [ 360.464883] driver_detach+0x4c/0x90 [ 360.468509] bus_remove_driver+0x54/0xb0 [ 360.472485] driver_unregister+0x2c/0x58 [ 360.476462] platform_driver_unregister+0x10/0x18 [ 360.481230] gpio_keys_exit+0x14/0x828 [gpio_keys] [ 360.486088] __arm64_sys_delete_module+0x1e0/0x270 [ 360.490945] invoke_syscall+0x40/0xf8 [ 360.494661] el0_svc_common.constprop.3+0xf0/0x110 [ 360.499515] do_el0_svc+0x20/0x78 [ 360.502877] el0_svc+0x48/0xf8 [ 360.505977] el0t_64_sync_handler+0x88/0xb0 [ 360.510216] el0t_64_sync+0x148/0x14c [ 360.513930] irq event stamp: 4306 [ 360.517288] hardirqs last enabled at (4305): [<ffff8000080b0300>] __cancel_work_timer+0x130/0x1b0 [ 360.526359] hardirqs last disabled at (4306): [<ffff800008d194fc>] el1_dbg+0x24/0x88 [ 360.534204] softirqs last enabled at (4278): [<ffff8000080104a0>] _stext+0x4a0/0x5e0 [ 360.542133] softirqs last disabled at (4267): [<ffff8000080932ac>] irq_exit_rcu+0x18c/0x1b0 [ 360.550591] ---[ end trace 0000000000000000 ]---Show less

In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Prevent panic when SDMA is disabled If the hfi1 module is loaded with HFI1_CAP_SDMA off, a call to hfi1_write_iter() will dereference a NULL pointer and panic. A typical stack frame is: sdma_select_user_engine [hfi1] hfi1_user_sdma_process_request [hfi1] hfi1_write_iter [hfi1] do_iter_readv_writev do_iter_write vfs_writev do_writev do_syscall_64 The fix is to test for SDMA in hfi1_write_iter() and fail the I/O with EINVAL.Show less

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on inline_dots inode As Wenqing reported in bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215765 It will cause a kernel panic with steps: - mkdir mnt - mount tmp40.img mnt - ls mnt folio_mark_dirty+0x33/0x50 f2fs_add_regular_entry+0x541/0xad0 [f2fs] f2fs_add_dentry+0x6c/0xb0 [f2fs] f2fs_do_add_link+0x182/0x230 [f2fs] __recover_dot_dentries+0x2d6/0x470 [f2fs] f2fs_lookup+0x5af/0x6a0 [f2fs] __lookup_slow+0xac/0x200 lookup_slow+0x45/0x70 walk_component+0x16c/0x250 path_lookupat+0x8b/0x1f0 filename_lookup+0xef/0x250 user_path_at_empty+0x46/0x70 vfs_statx+0x98/0x190 __do_sys_newlstat+0x41/0x90 __x64_sys_newlstat+0x1a/0x30 do_syscall_64+0x37/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae The root cause is for special file: e.g. character, block, fifo or socket file, f2fs doesn't assign address space operations pointer array for mapping->a_ops field, so, in a fuzzed image, if inline_dots flag was tagged in special file, during lookup(), when f2fs runs into __recover_dot_dentries(), it will cause NULL pointer access once f2fs_add_regular_entry() calls a_ops->set_dirty_page().Show less

In the Linux kernel, the following vulnerability has been resolved: iommu/mediatek: Remove clk_disable in mtk_iommu_remove After the commit b34ea31fe013 ("iommu/mediatek: Always enable the clk on resume"), the iommu clock is controlled by the runtime callback. thus remove the clk control in the mtk_iommu_remove. Otherwise, it will warning like: echo 14018000.iommu > /sys/bus/platform/drivers/mtk-iommu/unbind [ 51.413044] ------------[ cut here ]------------ [ 51.413648] vpp0_smi_iommu already disabled [ 51.414233] WARNING: CPU: 2 PID: 157 at */v5.15-rc1/kernel/mediatek/ drivers/clk/clk.c:952 clk_core_disable+0xb0/0xb8 [ 51.417174] Hardware name: MT8195V/C(ENG) (DT) [ 51.418635] pc : clk_core_disable+0xb0/0xb8 [ 51.419177] lr : clk_core_disable+0xb0/0xb8 ... [ 51.429375] Call trace: [ 51.429694] clk_core_disable+0xb0/0xb8 [ 51.430193] clk_core_disable_lock+0x24/0x40 [ 51.430745] clk_disable+0x20/0x30 [ 51.431189] mtk_iommu_remove+0x58/0x118 [ 51.431705] platform_remove+0x28/0x60 [ 51.432197] device_release_driver_internal+0x110/0x1f0 [ 51.432873] device_driver_detach+0x18/0x28 [ 51.433418] unbind_store+0xd4/0x108 [ 51.433886] drv_attr_store+0x24/0x38 [ 51.434363] sysfs_kf_write+0x40/0x58 [ 51.434843] kernfs_fop_write_iter+0x164/0x1e0Show less

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu-v3-sva: Fix mm use-after-free We currently call arm64_mm_context_put() without holding a reference to the mm, which can result in use-after-free. Call mmgrab()/mmdrop() to ensure the mm only gets freed after we unpinned the ASID.Show less

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix dereference of stale list iterator after loop body The list iterator variable will be a bogus pointer if no break was hit. Dereferencing it (cur->page in this case) could load an out-of-bounds/undefined value making it unsafe to use that in the comparision to determine if the specific element was found. Since 'cur->page' *can* be out-ouf-bounds it cannot be guaranteed that by chance (or intention of an attacker) it matches the value of 'page' even though the correct element was not found. This is fixed by using a separate list iterator variable for the loop and only setting the original variable if a suitable element was found. Then determing if the element was found is simply checking if the variable is set.Show less

In the Linux kernel, the following vulnerability has been resolved: iommu/mediatek: Fix NULL pointer dereference when printing dev_name When larbdev is NULL (in the case I hit, the node is incorrectly set iommus = <&iommu NUM>), it will cause device_link_add() fail and kernel crashes when we try to print dev_name(larbdev). Let's fail the probe if a larbdev is NULL to avoid invalid inputs from dts. It should work for normal correct setting and avoid the crash caused by my incorrect setting. Error log: [ 18.189042][ T301] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050 ... [ 18.344519][ T301] pstate: a0400005 (NzCv daif +PAN -UAO) [ 18.345213][ T301] pc : mtk_iommu_probe_device+0xf8/0x118 [mtk_iommu] [ 18.346050][ T301] lr : mtk_iommu_probe_device+0xd0/0x118 [mtk_iommu] [ 18.346884][ T301] sp : ffffffc00a5635e0 [ 18.347392][ T301] x29: ffffffc00a5635e0 x28: ffffffd44a46c1d8 [ 18.348156][ T301] x27: ffffff80c39a8000 x26: ffffffd44a80cc38 [ 18.348917][ T301] x25: 0000000000000000 x24: ffffffd44a80cc38 [ 18.349677][ T301] x23: ffffffd44e4da4c6 x22: ffffffd44a80cc38 [ 18.350438][ T301] x21: ffffff80cecd1880 x20: 0000000000000000 [ 18.351198][ T301] x19: ffffff80c439f010 x18: ffffffc00a50d0c0 [ 18.351959][ T301] x17: ffffffffffffffff x16: 0000000000000004 [ 18.352719][ T301] x15: 0000000000000004 x14: ffffffd44eb5d420 [ 18.353480][ T301] x13: 0000000000000ad2 x12: 0000000000000003 [ 18.354241][ T301] x11: 00000000fffffad2 x10: c0000000fffffad2 [ 18.355003][ T301] x9 : a0d288d8d7142d00 x8 : a0d288d8d7142d00 [ 18.355763][ T301] x7 : ffffffd44c2bc640 x6 : 0000000000000000 [ 18.356524][ T301] x5 : 0000000000000080 x4 : 0000000000000001 [ 18.357284][ T301] x3 : 0000000000000000 x2 : 0000000000000005 [ 18.358045][ T301] x1 : 0000000000000000 x0 : 0000000000000000 [ 18.360208][ T301] Hardware name: MT6873 (DT) [ 18.360771][ T301] Call trace: [ 18.361168][ T301] dump_backtrace+0xf8/0x1f0 [ 18.361737][ T301] dump_stack_lvl+0xa8/0x11c [ 18.362305][ T301] dump_stack+0x1c/0x2c [ 18.362816][ T301] mrdump_common_die+0x184/0x40c [mrdump] [ 18.363575][ T301] ipanic_die+0x24/0x38 [mrdump] [ 18.364230][ T301] atomic_notifier_call_chain+0x128/0x2b8 [ 18.364937][ T301] die+0x16c/0x568 [ 18.365394][ T301] __do_kernel_fault+0x1e8/0x214 [ 18.365402][ T301] do_page_fault+0xb8/0x678 [ 18.366934][ T301] do_translation_fault+0x48/0x64 [ 18.368645][ T301] do_mem_abort+0x68/0x148 [ 18.368652][ T301] el1_abort+0x40/0x64 [ 18.368660][ T301] el1h_64_sync_handler+0x54/0x88 [ 18.368668][ T301] el1h_64_sync+0x68/0x6c [ 18.368673][ T301] mtk_iommu_probe_device+0xf8/0x118 [mtk_iommu] ...Show less

In the Linux kernel, the following vulnerability has been resolved: rtla: Avoid record NULL pointer dereference Fix the following null/deref_null.cocci errors: ./tools/tracing/rtla/src/osnoise_hist.c:870:31-36: ERROR: record is NULL but dereferenced. ./tools/tracing/rtla/src/osnoise_top.c:650:31-36: ERROR: record is NULL but dereferenced. ./tools/tracing/rtla/src/timerlat_hist.c:905:31-36: ERROR: record is NULL but dereferenced. ./tools/tracing/rtla/src/timerlat_top.c:700:31-36: ERROR: record is NULL but dereferenced. "record" is NULL before calling osnoise_init_trace_tool. Add a tag "out_free" to avoid dereferring a NULL pointer.Show less

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Fix the error handling path in idxd_cdev_register() If a call to alloc_chrdev_region() fails, the already allocated resources are leaking. Add the needed error handling path to fix the leak.Show less