Linux Kernel

In the Linux kernel, the following vulnerability has been resolved: usb: xhci: Apply the link chain quirk on NEC isoc endpoints Two clearly different specimens of NEC uPD720200 (one with start/stop bug, one without) were seen to cause IOMMU faults after some Missed Service Errors. Faulting address is immediately after a transfer ring segment and patched dynamic debug messages revealed that the MSE was received when waiting for a TD near the end of that segment: [ 1.041954] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ffa08fe0 [ 1.042120] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09000 flags=0x0000] [ 1.042146] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09040 flags=0x0000] It gets even funnier if the next page is a ring segment accessible to the HC. Below, it reports MSE in segment at ff1e8000, plows through a zero-filled page at ff1e9000 and starts reporting events for TRBs in page at ff1ea000 every microframe, instead of jumping to seg ff1e6000. [ 7.041671] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0 [ 7.041999] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0 [ 7.042011] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint [ 7.042028] xhci_hcd: All TDs skipped for slot 1 ep 2. Clear skip flag. [ 7.042134] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint [ 7.042138] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31 [ 7.042144] xhci_hcd: Looking for event-dma 00000000ff1ea040 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820 [ 7.042259] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint [ 7.042262] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31 [ 7.042266] xhci_hcd: Looking for event-dma 00000000ff1ea050 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820 At some point completion events change from Isoch Buffer Overrun to Short Packet and the HC finally finds cycle bit mismatch in ff1ec000. [ 7.098130] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13 [ 7.098132] xhci_hcd: Looking for event-dma 00000000ff1ecc50 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820 [ 7.098254] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13 [ 7.098256] xhci_hcd: Looking for event-dma 00000000ff1ecc60 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820 [ 7.098379] xhci_hcd: Overrun event on slot 1 ep 2 It's possible that data from the isochronous device were written to random buffers of pending TDs on other endpoints (either IN or OUT), other devices or even other HCs in the same IOMMU domain. Lastly, an error from a different USB device on another HC. Was it caused by the above? I don't know, but it may have been. The disk was working without any other issues and generated PCIe traffic to starve the NEC of upstream BW and trigger those MSEs. The two HCs shared one x1 slot by means of a commercial "PCIe splitter" board. [ 7.162604] usb 10-2: reset SuperSpeed USB device number 3 using xhci_hcd [ 7.178990] sd 9:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s [ 7.179001] sd 9:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 04 02 ae 00 00 02 00 00 [ 7.179004] I/O error, dev sdb, sector 67284480 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0 Fortunately, it appears that this ridiculous bug is avoided by setting the chain bit of Link TRBs on isochronous rings. Other ancient HCs are known which also expect the bit to be set and they ignore Link TRBs if it's not. Reportedly, 0.95 spec guaranteed that the bit is set. The bandwidth-starved NEC HC running a 32KB/uframe UVC endpoint reports tens of MSEs per second and runs into the bug within seconds. Chaining Link TRBs allows the same workload to run for many minutes, many times. No ne ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: netfilter: socket: Lookup orig tuple for IPv6 SNAT nf_sk_lookup_slow_v4 does the conntrack lookup for IPv4 packets to restore the original 5-tuple in case of SNAT, to be able to find the right socket (if any). Then socket_match() can correctly check whether the socket was transparent. However, the IPv6 counterpart (nf_sk_lookup_slow_v6) lacks this conntrack lookup, making xt_socket fail to match on the socket when the packet was SNATed. Add the same logic to nf_sk_lookup_slow_v6. IPv6 SNAT is used in Kubernetes clusters for pod-to-world packets, as pods' addresses are in the fd00::/8 ULA subnet and need to be replaced with the node's external address. Cilium leverages Envoy to enforce L7 policies, and Envoy uses transparent sockets. Cilium inserts an iptables prerouting rule that matches on `-m socket --transparent` and redirects the packets to localhost, but it fails to match SNATed IPv6 packets due to that missing conntrack lookup.Show less

In the Linux kernel, the following vulnerability has been resolved: memstick: rtsx_usb_ms: Fix slab-use-after-free in rtsx_usb_ms_drv_remove This fixes the following crash: ================================================================== BUG: KASAN: slab-use-after-free in rtsx_usb_ms_poll_card+0x159/0x200 [rtsx_usb_ms] Read of size 8 at addr ffff888136335380 by task kworker/6:0/140241 CPU: 6 UID: 0 PID: 140241 Comm: kworker/6:0 Kdump: loaded Tainted: G E 6.14.0-rc6+ #1 Tainted: [E]=UNSIGNED_MODULE Hardware name: LENOVO 30FNA1V7CW/1057, BIOS S0EKT54A 07/01/2024 Workqueue: events rtsx_usb_ms_poll_card [rtsx_usb_ms] Call Trace: <TASK> dump_stack_lvl+0x51/0x70 print_address_description.constprop.0+0x27/0x320 ? rtsx_usb_ms_poll_card+0x159/0x200 [rtsx_usb_ms] print_report+0x3e/0x70 kasan_report+0xab/0xe0 ? rtsx_usb_ms_poll_card+0x159/0x200 [rtsx_usb_ms] rtsx_usb_ms_poll_card+0x159/0x200 [rtsx_usb_ms] ? __pfx_rtsx_usb_ms_poll_card+0x10/0x10 [rtsx_usb_ms] ? __pfx___schedule+0x10/0x10 ? kick_pool+0x3b/0x270 process_one_work+0x357/0x660 worker_thread+0x390/0x4c0 ? __pfx_worker_thread+0x10/0x10 kthread+0x190/0x1d0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 161446: kasan_save_stack+0x20/0x40 kasan_save_track+0x10/0x30 __kasan_kmalloc+0x7b/0x90 __kmalloc_noprof+0x1a7/0x470 memstick_alloc_host+0x1f/0xe0 [memstick] rtsx_usb_ms_drv_probe+0x47/0x320 [rtsx_usb_ms] platform_probe+0x60/0xe0 call_driver_probe+0x35/0x120 really_probe+0x123/0x410 __driver_probe_device+0xc7/0x1e0 driver_probe_device+0x49/0xf0 __device_attach_driver+0xc6/0x160 bus_for_each_drv+0xe4/0x160 __device_attach+0x13a/0x2b0 bus_probe_device+0xbd/0xd0 device_add+0x4a5/0x760 platform_device_add+0x189/0x370 mfd_add_device+0x587/0x5e0 mfd_add_devices+0xb1/0x130 rtsx_usb_probe+0x28e/0x2e0 [rtsx_usb] usb_probe_interface+0x15c/0x460 call_driver_probe+0x35/0x120 really_probe+0x123/0x410 __driver_probe_device+0xc7/0x1e0 driver_probe_device+0x49/0xf0 __device_attach_driver+0xc6/0x160 bus_for_each_drv+0xe4/0x160 __device_attach+0x13a/0x2b0 rebind_marked_interfaces.isra.0+0xcc/0x110 usb_reset_device+0x352/0x410 usbdev_do_ioctl+0xe5c/0x1860 usbdev_ioctl+0xa/0x20 __x64_sys_ioctl+0xc5/0xf0 do_syscall_64+0x59/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 161506: kasan_save_stack+0x20/0x40 kasan_save_track+0x10/0x30 kasan_save_free_info+0x36/0x60 __kasan_slab_free+0x34/0x50 kfree+0x1fd/0x3b0 device_release+0x56/0xf0 kobject_cleanup+0x73/0x1c0 rtsx_usb_ms_drv_remove+0x13d/0x220 [rtsx_usb_ms] platform_remove+0x2f/0x50 device_release_driver_internal+0x24b/0x2e0 bus_remove_device+0x124/0x1d0 device_del+0x239/0x530 platform_device_del.part.0+0x19/0xe0 platform_device_unregister+0x1c/0x40 mfd_remove_devices_fn+0x167/0x170 device_for_each_child_reverse+0xc9/0x130 mfd_remove_devices+0x6e/0xa0 rtsx_usb_disconnect+0x2e/0xd0 [rtsx_usb] usb_unbind_interface+0xf3/0x3f0 device_release_driver_internal+0x24b/0x2e0 proc_disconnect_claim+0x13d/0x220 usbdev_do_ioctl+0xb5e/0x1860 usbdev_ioctl+0xa/0x20 __x64_sys_ioctl+0xc5/0xf0 do_syscall_64+0x59/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Last potentially related work creation: kasan_save_stack+0x20/0x40 kasan_record_aux_stack+0x85/0x90 insert_work+0x29/0x100 __queue_work+0x34a/0x540 call_timer_fn+0x2a/0x160 expire_timers+0x5f/0x1f0 __run_timer_base.part.0+0x1b6/0x1e0 run_timer_softirq+0x8b/0xe0 handle_softirqs+0xf9/0x360 __irq_exit_rcu+0x114/0x130 sysvec_apic_timer_interrupt+0x72/0x90 asm_sysvec_apic_timer_interrupt+0x16/0x20 Second to last potentially related work creation: kasan_save_stack+0x20/0x40 kasan_record_aux_stack+0x85/0x90 insert_work+0x29/0x100 __queue_work+0x34a/0x540 call_timer_fn+0x2a/0x160 expire_timers+0x5f/0x1f0 __run_timer_base.part.0+0x1b6/0x1e0 run_timer_softirq+0x8b/0xe0 handle_softirqs+0xf9/0x ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: bcachefs: bch2_ioctl_subvolume_destroy() fixes bch2_evict_subvolume_inodes() was getting stuck - due to incorrectly pruning the dcache. Also, fix missing permissions checks.Show less

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix legacy client tracking initialization Get rid of the nfsd4_legacy_tracking_ops->init() call in check_for_legacy_methods(). That will be handled in the caller (nfsd4_client_tracking_init()). Otherwise, we'll wind up calling nfsd4_legacy_tracking_ops->init() twice, and the second time we'll trigger the BUG_ON() in nfsd4_init_recdir().Show less

In the Linux kernel, the following vulnerability has been resolved: atm: Fix NULL pointer dereference When MPOA_cache_impos_rcvd() receives the msg, it can trigger Null Pointer Dereference Vulnerability if both entry and holding_time are NULL. Because there is only for the situation where entry is NULL and holding_time exists, it can be passed when both entry and holding_time are NULL. If these are NULL, the entry will be passd to eg_cache_put() as parameter and it is referenced by entry->use code in it. kasan log: [ 3.316691] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006:I [ 3.317568] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037] [ 3.318188] CPU: 3 UID: 0 PID: 79 Comm: ex Not tainted 6.14.0-rc2 #102 [ 3.318601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 [ 3.319298] RIP: 0010:eg_cache_remove_entry+0xa5/0x470 [ 3.319677] Code: c1 f7 6e fd 48 c7 c7 00 7e 38 b2 e8 95 64 54 fd 48 c7 c7 40 7e 38 b2 48 89 ee e80 [ 3.321220] RSP: 0018:ffff88800583f8a8 EFLAGS: 00010006 [ 3.321596] RAX: 0000000000000006 RBX: ffff888005989000 RCX: ffffffffaecc2d8e [ 3.322112] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000030 [ 3.322643] RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff6558b88 [ 3.323181] R10: 0000000000000003 R11: 203a207972746e65 R12: 1ffff11000b07f15 [ 3.323707] R13: dffffc0000000000 R14: ffff888005989000 R15: ffff888005989068 [ 3.324185] FS: 000000001b6313c0(0000) GS:ffff88806d380000(0000) knlGS:0000000000000000 [ 3.325042] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.325545] CR2: 00000000004b4b40 CR3: 000000000248e000 CR4: 00000000000006f0 [ 3.326430] Call Trace: [ 3.326725] <TASK> [ 3.326927] ? die_addr+0x3c/0xa0 [ 3.327330] ? exc_general_protection+0x161/0x2a0 [ 3.327662] ? asm_exc_general_protection+0x26/0x30 [ 3.328214] ? vprintk_emit+0x15e/0x420 [ 3.328543] ? eg_cache_remove_entry+0xa5/0x470 [ 3.328910] ? eg_cache_remove_entry+0x9a/0x470 [ 3.329294] ? __pfx_eg_cache_remove_entry+0x10/0x10 [ 3.329664] ? console_unlock+0x107/0x1d0 [ 3.329946] ? __pfx_console_unlock+0x10/0x10 [ 3.330283] ? do_syscall_64+0xa6/0x1a0 [ 3.330584] ? entry_SYSCALL_64_after_hwframe+0x47/0x7f [ 3.331090] ? __pfx_prb_read_valid+0x10/0x10 [ 3.331395] ? down_trylock+0x52/0x80 [ 3.331703] ? vprintk_emit+0x15e/0x420 [ 3.331986] ? __pfx_vprintk_emit+0x10/0x10 [ 3.332279] ? down_trylock+0x52/0x80 [ 3.332527] ? _printk+0xbf/0x100 [ 3.332762] ? __pfx__printk+0x10/0x10 [ 3.333007] ? _raw_write_lock_irq+0x81/0xe0 [ 3.333284] ? __pfx__raw_write_lock_irq+0x10/0x10 [ 3.333614] msg_from_mpoad+0x1185/0x2750 [ 3.333893] ? __build_skb_around+0x27b/0x3a0 [ 3.334183] ? __pfx_msg_from_mpoad+0x10/0x10 [ 3.334501] ? __alloc_skb+0x1c0/0x310 [ 3.334809] ? __pfx___alloc_skb+0x10/0x10 [ 3.335283] ? _raw_spin_lock+0xe0/0xe0 [ 3.335632] ? finish_wait+0x8d/0x1e0 [ 3.335975] vcc_sendmsg+0x684/0xba0 [ 3.336250] ? __pfx_vcc_sendmsg+0x10/0x10 [ 3.336587] ? __pfx_autoremove_wake_function+0x10/0x10 [ 3.337056] ? fdget+0x176/0x3e0 [ 3.337348] __sys_sendto+0x4a2/0x510 [ 3.337663] ? __pfx___sys_sendto+0x10/0x10 [ 3.337969] ? ioctl_has_perm.constprop.0.isra.0+0x284/0x400 [ 3.338364] ? sock_ioctl+0x1bb/0x5a0 [ 3.338653] ? __rseq_handle_notify_resume+0x825/0xd20 [ 3.339017] ? __pfx_sock_ioctl+0x10/0x10 [ 3.339316] ? __pfx___rseq_handle_notify_resume+0x10/0x10 [ 3.339727] ? selinux_file_ioctl+0xa4/0x260 [ 3.340166] __x64_sys_sendto+0xe0/0x1c0 [ 3.340526] ? syscall_exit_to_user_mode+0x123/0x140 [ 3.340898] do_syscall_64+0xa6/0x1a0 [ 3.341170] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 3.341533] RIP: 0033:0x44a380 [ 3.341757] Code: 0f 1f 84 00 00 00 00 00 66 90 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c00 [ ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: devlink: fix xa_alloc_cyclic() error handling In case of returning 1 from xa_alloc_cyclic() (wrapping) ERR_PTR(1) will be returned, which will cause IS_ERR() to be false. Which can lead to dereference not allocated pointer (rel). Fix it by checking if err is lower than zero. This wasn't found in real usecase, only noticed. Credit to Pierre.Show less

In the Linux kernel, the following vulnerability has been resolved: dpll: fix xa_alloc_cyclic() error handling In case of returning 1 from xa_alloc_cyclic() (wrapping) ERR_PTR(1) will be returned, which will cause IS_ERR() to be false. Which can lead to dereference not allocated pointer (pin). Fix it by checking if err is lower than zero. This wasn't found in real usecase, only noticed. Credit to Pierre.Show less

In the Linux kernel, the following vulnerability has been resolved: mm/migrate: fix shmem xarray update during migration A shmem folio can be either in page cache or in swap cache, but not at the same time. Namely, once it is in swap cache, folio->mapping should be NULL, and the folio is no longer in a shmem mapping. In __folio_migrate_mapping(), to determine the number of xarray entries to update, folio_test_swapbacked() is used, but that conflates shmem in page cache case and shmem in swap cache case. It leads to xarray multi-index entry corruption, since it turns a sibling entry to a normal entry during xas_store() (see [1] for a userspace reproduction). Fix it by only using folio_test_swapcache() to determine whether xarray is storing swap cache entries or not to choose the right number of xarray entries to update. [1] https://lore.kernel.org/linux-mm/Z8idPCkaJW1IChjT@casper.infradead.org/ Note: In __split_huge_page(), folio_test_anon() && folio_test_swapcache() is used to get swap_cache address space, but that ignores the shmem folio in swap cache case. It could lead to NULL pointer dereferencing when a in-swap-cache shmem folio is split at __xa_store(), since !folio_test_anon() is true and folio->mapping is NULL. But fortunately, its caller split_huge_page_to_list_to_order() bails out early with EBUSY when folio->mapping is NULL. So no need to take care of it here.Show less

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: pdr: Fix the potential deadlock When some client process A call pdr_add_lookup() to add the look up for the service and does schedule locator work, later a process B got a new server packet indicating locator is up and call pdr_locator_new_server() which eventually sets pdr->locator_init_complete to true which process A sees and takes list lock and queries domain list but it will timeout due to deadlock as the response will queued to the same qmi->wq and it is ordered workqueue and process B is not able to complete new server request work due to deadlock on list lock. Fix it by removing the unnecessary list iteration as the list iteration is already being done inside locator work, so avoid it here and just call schedule_work() here. Process A Process B process_scheduled_works() pdr_add_lookup() qmi_data_ready_work() process_scheduled_works() pdr_locator_new_server() pdr->locator_init_complete=true; pdr_locator_work() mutex_lock(&pdr->list_lock); pdr_locate_service() mutex_lock(&pdr->list_lock); pdr_get_domain_list() pr_err("PDR: %s get domain list txn wait failed: %d\n", req->service_name, ret); Timeout error log due to deadlock: " PDR: tms/servreg get domain list txn wait failed: -110 PDR: service lookup for msm/adsp/sensor_pd:tms/servreg failed: -110 " Thanks to Bjorn and Johan for letting me know that this commit also fixes an audio regression when using the in-kernel pd-mapper as that makes it easier to hit this race. [1]Show less

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state There are several problems with the way hyp code lazily saves the host's FPSIMD/SVE state, including: * Host SVE being discarded unexpectedly due to inconsistent configuration of TIF_SVE and CPACR_ELx.ZEN. This has been seen to result in QEMU crashes where SVE is used by memmove(), as reported by Eric Auger: https://issues.redhat.com/browse/RHEL-68997 * Host SVE state is discarded *after* modification by ptrace, which was an unintentional ptrace ABI change introduced with lazy discarding of SVE state. * The host FPMR value can be discarded when running a non-protected VM, where FPMR support is not exposed to a VM, and that VM uses FPSIMD/SVE. In these cases the hyp code does not save the host's FPMR before unbinding the host's FPSIMD/SVE/SME state, leaving a stale value in memory. Avoid these by eagerly saving and "flushing" the host's FPSIMD/SVE/SME state when loading a vCPU such that KVM does not need to save any of the host's FPSIMD/SVE/SME state. For clarity, fpsimd_kvm_prepare() is removed and the necessary call to fpsimd_save_and_flush_cpu_state() is placed in kvm_arch_vcpu_load_fp(). As 'fpsimd_state' and 'fpmr_ptr' should not be used, they are set to NULL; all uses of these will be removed in subsequent patches. Historical problems go back at least as far as v5.17, e.g. erroneous assumptions about TIF_SVE being clear in commit: 8383741ab2e773a9 ("KVM: arm64: Get rid of host SVE tracking/saving") ... and so this eager save+flush probably needs to be backported to ALL stable trees.Show less

In the Linux kernel, the following vulnerability has been resolved: Revert "arm64: dts: qcom: sdm845: Affirm IDR0.CCTW on apps_smmu" There are reports that the pagetable walker cache coherency is not a given across the spectrum of SDM845/850 devices, leading to lock-ups and resets. It works fine on some devices (like the Dragonboard 845c, but not so much on the Lenovo Yoga C630). This unfortunately looks like a fluke in firmware development, where likely somewhere in the vast hypervisor stack, a change to accommodate for this was only introduced after the initial software release (which often serves as a baseline for products). Revert the change to avoid additional guesswork around crashes. This reverts commit 6b31a9744b8726c69bb0af290f8475a368a4b805.Show less

In the Linux kernel, the following vulnerability has been resolved: ARM: dts: bcm2711: Fix xHCI power-domain During s2idle tests on the Raspberry CM4 the VPU firmware always crashes on xHCI power-domain resume: root@raspberrypi:/sys/power# echo freeze > state [ 70.724347] xhci_suspend finished [ 70.727730] xhci_plat_suspend finished [ 70.755624] bcm2835-power bcm2835-power: Power grafx off [ 70.761127] USB: Set power to 0 [ 74.653040] USB: Failed to set power to 1 (-110) This seems to be caused because of the mixed usage of raspberrypi-power and bcm2835-power at the same time. So avoid the usage of the VPU firmware power-domain driver, which prevents the VPU crash.Show less

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix soft lockup during bt pages loop Driver runs a for-loop when allocating bt pages and mapping them with buffer pages. When a large buffer (e.g. MR over 100GB) is being allocated, it may require a considerable loop count. This will lead to soft lockup: watchdog: BUG: soft lockup - CPU#27 stuck for 22s! ... Call trace: hem_list_alloc_mid_bt+0x124/0x394 [hns_roce_hw_v2] hns_roce_hem_list_request+0xf8/0x160 [hns_roce_hw_v2] hns_roce_mtr_create+0x2e4/0x360 [hns_roce_hw_v2] alloc_mr_pbl+0xd4/0x17c [hns_roce_hw_v2] hns_roce_reg_user_mr+0xf8/0x190 [hns_roce_hw_v2] ib_uverbs_reg_mr+0x118/0x290 watchdog: BUG: soft lockup - CPU#35 stuck for 23s! ... Call trace: hns_roce_hem_list_find_mtt+0x7c/0xb0 [hns_roce_hw_v2] mtr_map_bufs+0xc4/0x204 [hns_roce_hw_v2] hns_roce_mtr_create+0x31c/0x3c4 [hns_roce_hw_v2] alloc_mr_pbl+0xb0/0x160 [hns_roce_hw_v2] hns_roce_reg_user_mr+0x108/0x1c0 [hns_roce_hw_v2] ib_uverbs_reg_mr+0x120/0x2bc Add a cond_resched() to fix soft lockup during these loops. In order not to affect the allocation performance of normal-size buffer, set the loop count of a 100GB MR as the threshold to call cond_resched().Show less

In the Linux kernel, the following vulnerability has been resolved: regulator: dummy: force synchronous probing Sometimes I get a NULL pointer dereference at boot time in kobject_get() with the following call stack: anatop_regulator_probe() devm_regulator_register() regulator_register() regulator_resolve_supply() kobject_get() By placing some extra BUG_ON() statements I could verify that this is raised because probing of the 'dummy' regulator driver is not completed ('dummy_regulator_rdev' is still NULL). In the JTAG debugger I can see that dummy_regulator_probe() and anatop_regulator_probe() can be run by different kernel threads (kworker/u4:*). I haven't further investigated whether this can be changed or if there are other possibilities to force synchronization between these two probe routines. On the other hand I don't expect much boot time penalty by probing the 'dummy' regulator synchronously.Show less

In the Linux kernel, the following vulnerability has been resolved: regulator: check that dummy regulator has been probed before using it Due to asynchronous driver probing there is a chance that the dummy regulator hasn't already been probed when first accessing it.Show less

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix error code in chan_alloc_skb_cb() The chan_alloc_skb_cb() function is supposed to return error pointers on error. Returning NULL will lead to a NULL dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw: Fix NAPI registration sequence Registering the interrupts for TX or RX DMA Channels prior to registering their respective NAPI callbacks can result in a NULL pointer dereference. This is seen in practice as a random occurrence since it depends on the randomness associated with the generation of traffic by Linux and the reception of traffic from the wire.Show less

In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix memleak of nhc_pcpu_rth_output in fib_check_nh_v6_gw(). fib_check_nh_v6_gw() expects that fib6_nh_init() cleans up everything when it fails. Commit 7dd73168e273 ("ipv6: Always allocate pcpu memory in a fib6_nh") moved fib_nh_common_init() before alloc_percpu_gfp() within fib6_nh_init() but forgot to add cleanup for fib6_nh->nh_common.nhc_pcpu_rth_output in case it fails to allocate fib6_nh->rt6i_pcpu, resulting in memleak. Let's call fib_nh_common_release() and clear nhc_pcpu_rth_output in the error path. Note that we can remove the fib6_nh_release() call in nh_create_ipv6() later in net-next.git.Show less