Linux Kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer Dereference (NPD) conditions were observed in the lifecycle management of hci_uart. The primary issue arises because the workqueues (init_ready and write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY flag is set during TTY close. If a hangup occurs before setup completes, hci_uart_tty_close() skips the teardown of these workqueues and proceeds to free the `hu` struct. When the scheduled work executes later, it blindly dereferences the freed `hu` struct. Furthermore, several data races and UAFs were identified in the teardown sequence: 1. Calling hci_uart_flush() from hci_uart_close() without effectively disabling write_work causes a race condition where both can concurrently double-free hu->tx_skb. This happens because protocol timers can concurrently invoke hci_uart_tx_wakeup() and requeue write_work. 2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF when vendor specific protocol close callbacks dereference hu->hdev. 3. In the initialization error paths, failing to take the proto_lock write lock before clearing PROTO_READY leads to races with active readers. Additionally, hci_uart_tty_receive() accesses hu->hdev outside the read lock, leading to UAFs if the initialization error path frees hdev concurrently. Fix these synchronization and lifecycle issues by: 1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first, followed immediately by a cancel_work_sync(&hu->write_work). Clearing the flag locks out concurrent protocol timers from successfully invoking hci_uart_tx_wakeup(), effectively rendering the cancellation permanent and preventing the tx_skb double-free. 2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip hu->proto->flush(). This is perfectly safe in the tty_close path because hu->proto->close() executes shortly after, which intrinsically purges all protocol SKB queues and tears down the state. 3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev) across all close and error paths to prevent vendor-level UAFs. 4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive() inside the proto_lock read-side critical section to safely synchronize with device unregistration. 5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely flush the workqueue before hci_uart_flush() is invoked via the HCI core. 6. Utilizing cancel_work_sync() instead of disable_work_sync() across all paths to prevent permanently breaking user-space retry capabilities.Show less

In the Linux kernel, the following vulnerability has been resolved: io-wq: check that the predecessor is hashed in io_wq_remove_pending() io_wq_remove_pending() needs to fix up wq->hash_tail[] if the cancelled work was the tail of its hash bucket. When doing this, it checks whether the preceding entry in acct->work_list has the same hash value, but never checks that the predecessor is hashed at all. io_get_work_hash() is simply atomic_read(&work->flags) >> IO_WQ_HASH_SHIFT, and the hash bits are never set for non-hashed work, so it returns 0. Thus, when a hashed bucket-0 work is cancelled while a non-hashed work is its list predecessor, the check spuriously passes and a pointer to the non-hashed io_kiocb is stored in wq->hash_tail[0]. Because non-hashed work is dequeued via the fast path in io_get_next_work(), which never touches hash_tail[], the stale pointer is never cleared. Therefore, after the non-hashed io_kiocb completes and is freed back to req_cachep, wq->hash_tail[0] is a dangling pointer. The io_wq is per-task (tctx->io_wq) and survives ring open/close, so the dangling pointer persists for the lifetime of the task; the next hashed bucket-0 enqueue dereferences it in io_wq_insert_work() and wq_list_add_after() writes through freed memory. Add the missing io_wq_is_hashed() check so a non-hashed predecessor never inherits a hash_tail[] slot.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/vkms: Convert to DRM's vblank timer Replace vkms' vblank timer with the DRM implementation. The DRM code is identical in concept, but differs in implementation. Vblank timers are covered in vblank helpers and initializer macros, so remove the corresponding hrtimer in struct vkms_output. The vblank timer calls vkms' custom timeout code via handle_vblank_timeout in struct drm_crtc_helper_funcs.Show less

In the Linux kernel, the following vulnerability has been resolved: ibmveth: Disable GSO for packets with small MSS Some physical adapters on Power systems do not support segmentation offload when the MSS is less than 224 bytes. Attempting to send such packets causes the adapter to freeze, stopping all traffic until manually reset. Implement ndo_features_check to disable GSO for packets with small MSS values. The network stack will perform software segmentation instead. The 224-byte minimum matches ibmvnic commit <f10b09ef687f> ("ibmvnic: Enforce stronger sanity checks on GSO packets") which uses the same physical adapters in SEA configurations. The issue occurs specifically when the hardware attempts to perform segmentation (gso_segs > 1) with a small MSS. Single-segment GSO packets (gso_segs == 1) do not trigger the problematic LSO code path and are transmitted normally without segmentation. Add an ndo_features_check callback to disable GSO when MSS < 224 bytes. Also call vlan_features_check() to ensure proper handling of VLAN packets, particularly QinQ (802.1ad) configurations where the hardware parser may not support certain offload features. Validated using iptables to force small MSS values. Without the fix, the adapter freezes. With the fix, packets are segmented in software and transmission succeeds. Comprehensive regression testing completedd (MSS tests, performance, stability).Show less

In the Linux kernel, the following vulnerability has been resolved: coresight: tmc-etr: Fix race condition between sysfs and perf mode When trying to run perf and sysfs mode simultaneously, the WARN_ON() in tmc_etr_enable_hw() is triggered sometimes: WARNING: CPU: 42 PID: 3911571 at drivers/hwtracing/coresight/coresight-tmc-etr.c:1060 tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] [..snip..] Call trace: tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] (P) tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] (L) tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] coresight_enable_path+0x1c8/0x218 [coresight] coresight_enable_sysfs+0xa4/0x228 [coresight] enable_source_store+0x58/0xa8 [coresight] dev_attr_store+0x20/0x40 sysfs_kf_write+0x4c/0x68 kernfs_fop_write_iter+0x120/0x1b8 vfs_write+0x2c8/0x388 ksys_write+0x74/0x108 __arm64_sys_write+0x24/0x38 el0_svc_common.constprop.0+0x64/0x148 do_el0_svc+0x24/0x38 el0_svc+0x3c/0x130 el0t_64_sync_handler+0xc8/0xd0 el0t_64_sync+0x1ac/0x1b0 ---[ end trace 0000000000000000 ]--- Since the enablement of sysfs mode is separeted into two critical regions, one for sysfs buffer allocation and another for hardware enablement, it's possible to race with the perf mode. Fix this by double check whether the perf mode's been used before enabling the hardware in sysfs mode. mode: [sysfs mode] [perf mode] tmc_etr_get_sysfs_buffer() spin_lock(&drvdata->spinlock) [sysfs buffer allocation] spin_unlock(&drvdata->spinlock) spin_lock(&drvdata->spinlock) tmc_etr_enable_hw() drvdata->etr_buf = etr_perf->etr_buf spin_unlock(&drvdata->spinlock) spin_lock(&drvdata->spinlock) tmc_etr_enable_hw() WARN_ON(drvdata->etr_buf) // WARN sicne etr_buf initialized at the perf side spin_unlock(&drvdata->spinlock) With this fix, we retain the check for CS_MODE_PERF in get_etr_sysfs_buf. This ensures we verify whether the perf mode's already running before we actually allocate the buffer. Then we can save the time of allocating/freeing the sysfs buffer if race with the perf mode.Show less

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: do WoW offloads only on primary link In case of multi-link connection, WCN7850 firmware crashes due to WoW offloads enabled on both primary and secondary links. Change to do it only on primary link to fix it. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1Show less

In the Linux kernel, the following vulnerability has been resolved: power: supply: rt9455: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.Show less

In the Linux kernel, the following vulnerability has been resolved: pinctrl: canaan: k230: Fix NULL pointer dereference when parsing devicetree When probing the k230 pinctrl driver, the kernel triggers a NULL pointer dereference. The crash trace showed: [ 0.732084] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000068 [ 0.740737] ... [ 0.776296] epc : k230_pinctrl_probe+0x1be/0x4fc In k230_pinctrl_parse_functions(), we attempt to retrieve the device pointer via info->pctl_dev->dev, but info->pctl_dev is only initialized after k230_pinctrl_parse_dt() completes. At the time of DT parsing, info->pctl_dev is still NULL, leading to the invalid dereference of info->pctl_dev->dev. Use the already available device pointer from platform_device instead of accessing through uninitialized pctl_dev.Show less

In the Linux kernel, the following vulnerability has been resolved: PCI/P2PDMA: Fix p2pmem_alloc_mmap() warning condition Commit b7e282378773 has already changed the initial page refcount of p2pdma page from one to zero, however, in p2pmem_alloc_mmap() it uses "VM_WARN_ON_ONCE_PAGE(!page_ref_count(page))" to assert the initial page refcount should not be zero and the following will be reported when CONFIG_DEBUG_VM is enabled: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x380400000 flags: 0x20000000002000(reserved|node=0|zone=4) raw: 0020000000002000 ff1100015e3ab440 0000000000000000 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: VM_WARN_ON_ONCE_PAGE(!page_ref_count(page)) ------------[ cut here ]------------ WARNING: CPU: 5 PID: 449 at drivers/pci/p2pdma.c:240 p2pmem_alloc_mmap+0x83a/0xa60 Fix by using "page_ref_count(page)" as the assertion condition.Show less

In the Linux kernel, the following vulnerability has been resolved: nfc: hci: shdlc: Stop timers and work before freeing context llc_shdlc_deinit() purges SHDLC skb queues and frees the llc_shdlc structure while its timers and state machine work may still be active. Timer callbacks can schedule sm_work, and sm_work accesses SHDLC state and the skb queues. If teardown happens in parallel with a queued/running work item, it can lead to UAF and other shutdown races. Stop all SHDLC timers and cancel sm_work synchronously before purging the queues and freeing the context. Found by Linux Verification Center (linuxtesting.org) with SVACE.Show less

In the Linux kernel, the following vulnerability has been resolved: inet: RAW sockets using IPPROTO_RAW MUST drop incoming ICMP Yizhou Zhao reported that simply having one RAW socket on protocol IPPROTO_RAW (255) was dangerous. socket(AF_INET, SOCK_RAW, 255); A malicious incoming ICMP packet can set the protocol field to 255 and match this socket, leading to FNHE cache changes. inner = IP(src="192.168.2.1", dst="8.8.8.8", proto=255)/Raw("TEST") pkt = IP(src="192.168.1.1", dst="192.168.2.1")/ICMP(type=3, code=4, nexthopmtu=576)/inner "man 7 raw" states: A protocol of IPPROTO_RAW implies enabled IP_HDRINCL and is able to send any IP protocol that is specified in the passed header. Receiving of all IP protocols via IPPROTO_RAW is not possible using raw sockets. Make sure we drop these malicious packets.Show less

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix WQ_MEM_RECLAIM warning When sunrpc is used, if a reset triggered, our wq may lead the following trace: workqueue: WQ_MEM_RECLAIM xprtiod:xprt_rdma_connect_worker [rpcrdma] is flushing !WQ_MEM_RECLAIM hns_roce_irq_workq:flush_work_handle [hns_roce_hw_v2] WARNING: CPU: 0 PID: 8250 at kernel/workqueue.c:2644 check_flush_dependency+0xe0/0x144 Call trace: check_flush_dependency+0xe0/0x144 start_flush_work.constprop.0+0x1d0/0x2f0 __flush_work.isra.0+0x40/0xb0 flush_work+0x14/0x30 hns_roce_v2_destroy_qp+0xac/0x1e0 [hns_roce_hw_v2] ib_destroy_qp_user+0x9c/0x2b4 rdma_destroy_qp+0x34/0xb0 rpcrdma_ep_destroy+0x28/0xcc [rpcrdma] rpcrdma_ep_put+0x74/0xb4 [rpcrdma] rpcrdma_xprt_disconnect+0x1d8/0x260 [rpcrdma] xprt_rdma_connect_worker+0xc0/0x120 [rpcrdma] process_one_work+0x1cc/0x4d0 worker_thread+0x154/0x414 kthread+0x104/0x144 ret_from_fork+0x10/0x18 Since QP destruction frees memory, this wq should have the WQ_MEM_RECLAIM.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/xe/pf: Fix sysfs initialization In case of devm_add_action_or_reset() failure the provided cleanup action will be run immediately on the not yet initialized kobject. This may lead to errors like: [ ] kobject: '(null)' (ff110001393608e0): is not initialized, yet kobject_put() is being called. [ ] WARNING: lib/kobject.c:734 at kobject_put+0xd9/0x250, CPU#0: kworker/0:0/9 [ ] RIP: 0010:kobject_put+0xdf/0x250 [ ] Call Trace: [ ] xe_sriov_pf_sysfs_init+0x21/0x100 [xe] [ ] xe_sriov_pf_init_late+0x87/0x2b0 [xe] [ ] xe_sriov_init_late+0x5f/0x2c0 [xe] [ ] xe_device_probe+0x5f2/0xc20 [xe] [ ] xe_pci_probe+0x396/0x610 [xe] [ ] local_pci_probe+0x47/0xb0 [ ] refcount_t: underflow; use-after-free. [ ] WARNING: lib/refcount.c:28 at refcount_warn_saturate+0x68/0xb0, CPU#0: kworker/0:0/9 [ ] RIP: 0010:refcount_warn_saturate+0x68/0xb0 [ ] Call Trace: [ ] kobject_put+0x174/0x250 [ ] xe_sriov_pf_sysfs_init+0x21/0x100 [xe] [ ] xe_sriov_pf_init_late+0x87/0x2b0 [xe] [ ] xe_sriov_init_late+0x5f/0x2c0 [xe] [ ] xe_device_probe+0x5f2/0xc20 [xe] [ ] xe_pci_probe+0x396/0x610 [xe] [ ] local_pci_probe+0x47/0xb0 Fix that by calling kobject_init() and kobject_add() separately and register cleanup action after the kobject is initialized. Also make this cleanup registration a part of the create helper to fix another mistake, as in the loop we were wrongly passing parent kobject while registering cleanup action, and this resulted in some undetected leaks. (cherry picked from commit 98b16727f07e26a5d4de84d88805ce7ffcfdd324)Show less

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix out-of-bounds stream encoder index v3 eng_id can be negative and that stream_enc_regs[] can be indexed out of bounds. eng_id is used directly as an index into stream_enc_regs[], which has only 5 entries. When eng_id is 5 (ENGINE_ID_DIGF) or negative, this can access memory past the end of the array. Add a bounds check using ARRAY_SIZE() before using eng_id as an index. The unsigned cast also rejects negative values. This avoids out-of-bounds access. Fixes the below smatch error: dcn*_resource.c: stream_encoder_create() may index stream_enc_regs[eng_id] out of bounds (size 5). drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn351/dcn351_resource.c 1246 static struct stream_encoder *dcn35_stream_encoder_create( 1247 enum engine_id eng_id, 1248 struct dc_context *ctx) 1249 { ... 1255 1256 /* Mapping of VPG, AFMT, DME register blocks to DIO block instance */ 1257 if (eng_id <= ENGINE_ID_DIGF) { ENGINE_ID_DIGF is 5. should <= be <? Unrelated but, ugh, why is Smatch saying that "eng_id" can be negative? end_id is type signed long, but there are checks in the caller which prevent it from being negative. 1258 vpg_inst = eng_id; 1259 afmt_inst = eng_id; 1260 } else 1261 return NULL; 1262 ... 1281 1282 dcn35_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios, 1283 eng_id, vpg, afmt, --> 1284 &stream_enc_regs[eng_id], ^^^^^^^^^^^^^^^^^^^^^^^ This stream_enc_regs[] array has 5 elements so we are one element beyond the end of the array. ... 1287 return &enc1->base; 1288 } v2: use explicit bounds check as suggested by Roman/Dan; avoid unsigned int cast v3: The compiler already knows how to compare the two values, so the cast (int) is not needed. (Roman)Show less

In the Linux kernel, the following vulnerability has been resolved: ASoC: fsl_xcvr: Revert fix missing lock in fsl_xcvr_mode_put() This reverts commit f51424872760 ("ASoC: fsl_xcvr: fix missing lock in fsl_xcvr_mode_put()"). The original patch attempted to acquire the card->controls_rwsem lock in fsl_xcvr_mode_put(). However, this function is called from the upper ALSA core function snd_ctl_elem_write(), which already holds the write lock on controls_rwsem for the whole put operation. So there is no need to simply hold the lock for fsl_xcvr_activate_ctl() again. Acquiring the read lock while holding the write lock in the same thread results in a deadlock and a hung task, as reported by Alexander Stein.Show less

In the Linux kernel, the following vulnerability has been resolved: spi: wpcm-fiu: Fix potential NULL pointer dereference in wpcm_fiu_probe() platform_get_resource_byname() can return NULL, which would cause a crash when passed the pointer to resource_size(). Move the fiu->memory_size assignment after the error check for devm_ioremap_resource() to prevent the potential NULL pointer dereference.Show less

In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix out-of-bound access in fib6_add_rt2node(). syzbot reported out-of-bound read in fib6_add_rt2node(). [0] When IPv6 route is created with RTA_NH_ID, struct fib6_info does not have the trailing struct fib6_nh. The cited commit started to check !iter->fib6_nh->fib_nh_gw_family to ensure that rt6_qualify_for_ecmp() will return false for iter. If iter->nh is not NULL, rt6_qualify_for_ecmp() returns false anyway. Let's check iter->nh before reading iter->fib6_nh and avoid OOB read. [0]: BUG: KASAN: slab-out-of-bounds in fib6_add_rt2node+0x349c/0x3500 net/ipv6/ip6_fib.c:1142 Read of size 1 at addr ffff8880384ba6de by task syz.0.18/5500 CPU: 0 UID: 0 PID: 5500 Comm: syz.0.18 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xba/0x230 mm/kasan/report.c:482 kasan_report+0x117/0x150 mm/kasan/report.c:595 fib6_add_rt2node+0x349c/0x3500 net/ipv6/ip6_fib.c:1142 fib6_add_rt2node_nh net/ipv6/ip6_fib.c:1363 [inline] fib6_add+0x910/0x18c0 net/ipv6/ip6_fib.c:1531 __ip6_ins_rt net/ipv6/route.c:1351 [inline] ip6_route_add+0xde/0x1b0 net/ipv6/route.c:3957 inet6_rtm_newroute+0x268/0x19e0 net/ipv6/route.c:5660 rtnetlink_rcv_msg+0x7d5/0xbe0 net/core/rtnetlink.c:6958 netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] ____sys_sendmsg+0xa68/0xad0 net/socket.c:2592 ___sys_sendmsg+0x2a5/0x360 net/socket.c:2646 __sys_sendmsg net/socket.c:2678 [inline] __do_sys_sendmsg net/socket.c:2683 [inline] __se_sys_sendmsg net/socket.c:2681 [inline] __x64_sys_sendmsg+0x1bd/0x2a0 net/socket.c:2681 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe2/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f9316b9aeb9 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd8809b678 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f9316e15fa0 RCX: 00007f9316b9aeb9 RDX: 0000000000000000 RSI: 0000200000004380 RDI: 0000000000000003 RBP: 00007f9316c08c1f R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007f9316e15fac R14: 00007f9316e15fa0 R15: 00007f9316e15fa0 </TASK> Allocated by task 5499: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 poison_kmalloc_redzone mm/kasan/common.c:398 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:415 kasan_kmalloc include/linux/kasan.h:263 [inline] __do_kmalloc_node mm/slub.c:5657 [inline] __kmalloc_noprof+0x40c/0x7e0 mm/slub.c:5669 kmalloc_noprof include/linux/slab.h:961 [inline] kzalloc_noprof include/linux/slab.h:1094 [inline] fib6_info_alloc+0x30/0xf0 net/ipv6/ip6_fib.c:155 ip6_route_info_create+0x142/0x860 net/ipv6/route.c:3820 ip6_route_add+0x49/0x1b0 net/ipv6/route.c:3949 inet6_rtm_newroute+0x268/0x19e0 net/ipv6/route.c:5660 rtnetlink_rcv_msg+0x7d5/0xbe0 net/core/rtnetlink.c:6958 netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] ____sys_sendmsg+0xa68/0xad0 net/socket.c:2592 ___sys_s ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: procfs: fix missing RCU protection when reading real_parent in do_task_stat() When reading /proc/[pid]/stat, do_task_stat() accesses task->real_parent without proper RCU protection, which leads to: cpu 0 cpu 1 ----- ----- do_task_stat var = task->real_parent release_task call_rcu(delayed_put_task_struct) task_tgid_nr_ns(var) rcu_read_lock <--- Too late to protect task->real_parent! task_pid_ptr <--- UAF! rcu_read_unlock This patch uses task_ppid_nr_ns() instead of task_tgid_nr_ns() to add proper RCU protection for accessing task->real_parent.Show less

In the Linux kernel, the following vulnerability has been resolved: gpio: cdev: Avoid NULL dereference in linehandle_create() In linehandle_create(), there is a statement like this: retain_and_null_ptr(lh); Soon after, there is a debug printout that dereferences "lh", which will crash things. Avoid the crash by using handlereq.lines, which is the same value.Show less

In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/timer-sp804: Fix an Oops when read_current_timer is called on ARM32 platforms where the SP804 is not registered as the sched_clock. On SP804, the delay timer shares the same clkevt instance with sched_clock. On some platforms, when sp804_clocksource_and_sched_clock_init is called with use_sched_clock not set to 1, sched_clkevt is not properly initialized. However, sp804_register_delay_timer is invoked unconditionally, and read_current_timer() subsequently calls sp804_read on an uninitialized sched_clkevt, leading to a kernel Oops when accessing sched_clkevt->value. Declare a dedicated clkevt instance exclusively for delay timer, instead of sharing the same clkevt with sched_clock. This ensures that read_current_timer continues to work correctly regardless of whether SP804 is selected as the sched_clock.Show less