Linux Kernel

In the Linux kernel, the following vulnerability has been resolved: HID: quirks: Add quirk for 2 Chicony Electronics HP 5MP Cameras The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C) report a HID sensor interface that is not actually implemented. Attempting to access this non-functional sensor via iio_info causes system hangs as runtime PM tries to wake up an unresponsive sensor. Add these 2 devices to the HID ignore list since the sensor interface is non-functional by design and should not be exposed to userspace.Show less

In the Linux kernel, the following vulnerability has been resolved: tracing: Add down_write(trace_event_sem) when adding trace event When a module is loaded, it adds trace events defined by the module. It may also need to modify the modules trace printk formats to replace enum names with their values. If two modules are loaded at the same time, the adding of the event to the ftrace_events list can corrupt the walking of the list in the code that is modifying the printk format strings and crash the kernel. The addition of the event should take the trace_event_sem for write while it adds the new event. Also add a lockdep_assert_held() on that semaphore in __trace_add_event_dirs() as it iterates the list.Show less

In the Linux kernel, the following vulnerability has been resolved: dmaengine: nbpfaxi: Fix memory corruption in probe() The nbpf->chan[] array is allocated earlier in the nbpf_probe() function and it has "num_channels" elements. These three loops iterate one element farther than they should and corrupt memory. The changes to the second loop are more involved. In this case, we're copying data from the irqbuf[] array into the nbpf->chan[] array. If the data in irqbuf[i] is the error IRQ then we skip it, so the iterators are not in sync. I added a check to ensure that we don't go beyond the end of the irqbuf[] array. I'm pretty sure this can't happen, but it seemed harmless to add a check. On the other hand, after the loop has ended there is a check to ensure that the "chan" iterator is where we expect it to be. In the original code we went one element beyond the end of the array so the iterator wasn't in the correct place and it would always return -EINVAL. However, now it will always be in the correct place. I deleted the check since we know the result.Show less

In the Linux kernel, the following vulnerability has been resolved: net: phy: Don't register LEDs for genphy If a PHY has no driver, the genphy driver is probed/removed directly in phy_attach/detach. If the PHY's ofnode has an "leds" subnode, then the LEDs will be (un)registered when probing/removing the genphy driver. This could occur if the leds are for a non-generic driver that isn't loaded for whatever reason. Synchronously removing the PHY device in phy_detach leads to the following deadlock: rtnl_lock() ndo_close() ... phy_detach() phy_remove() phy_leds_unregister() led_classdev_unregister() led_trigger_set() netdev_trigger_deactivate() unregister_netdevice_notifier() rtnl_lock() There is a corresponding deadlock on the open/register side of things (and that one is reported by lockdep), but it requires a race while this one is deterministic. Generic PHYs do not support LEDs anyway, so don't bother registering them.Show less

In the Linux kernel, the following vulnerability has been resolved: net: airoha: fix potential use-after-free in airoha_npu_get() np->name was being used after calling of_node_put(np), which releases the node and can lead to a use-after-free bug. Previously, of_node_put(np) was called unconditionally after of_find_device_by_node(np), which could result in a use-after-free if pdev is NULL. This patch moves of_node_put(np) after the error check to ensure the node is only released after both the error and success cases are handled appropriately, preventing potential resource issues.Show less

In the Linux kernel, the following vulnerability has been resolved: phy: tegra: xusb: Fix unbalanced regulator disable in UTMI PHY mode When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code assumed that the regulator should be disabled. However, if the regulator is marked as always-on, regulator_is_enabled() continues to return true, leading to an incorrect attempt to disable a regulator which is not enabled. This can result in warnings such as: [ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004 _regulator_disable+0xe4/0x1a0 [ 250.155652] unbalanced disables for VIN_SYS_5V0 To fix this, we move the regulator control logic into tegra186_xusb_padctl_id_override() function since it's directly related to the ID override state. The regulator is now only disabled when the role transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID register. This ensures that regulator enable/disable operations are properly balanced and only occur when actually transitioning to/from host mode.Show less

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix copy-to-cache so that it performs collection with ceph+fscache The netfs copy-to-cache that is used by Ceph with local caching sets up a new request to write data just read to the cache. The request is started and then left to look after itself whilst the app continues. The request gets notified by the backing fs upon completion of the async DIO write, but then tries to wake up the app because NETFS_RREQ_OFFLOAD_COLLECTION isn't set - but the app isn't waiting there, and so the request just hangs. Fix this by setting NETFS_RREQ_OFFLOAD_COLLECTION which causes the notification from the backing filesystem to put the collection onto a work queue instead.Show less

In the Linux kernel, the following vulnerability has been resolved: net: libwx: fix the using of Rx buffer DMA The wx_rx_buffer structure contained two DMA address fields: 'dma' and 'page_dma'. However, only 'page_dma' was actually initialized and used to program the Rx descriptor. But 'dma' was uninitialized and used in some paths. This could lead to undefined behavior, including DMA errors or use-after-free, if the uninitialized 'dma' was used. Althrough such error has not yet occurred, it is worth fixing in the code.Show less

In the Linux kernel, the following vulnerability has been resolved: net: libwx: properly reset Rx ring descriptor When device reset is triggered by feature changes such as toggling Rx VLAN offload, wx->do_reset() is called to reinitialize Rx rings. The hardware descriptor ring may retain stale values from previous sessions. And only set the length to 0 in rx_desc[0] would result in building malformed SKBs. Fix it to ensure a clean slate after device reset. [ 549.186435] [ C16] ------------[ cut here ]------------ [ 549.186457] [ C16] kernel BUG at net/core/skbuff.c:2814! [ 549.186468] [ C16] Oops: invalid opcode: 0000 [#1] SMP NOPTI [ 549.186472] [ C16] CPU: 16 UID: 0 PID: 0 Comm: swapper/16 Kdump: loaded Not tainted 6.16.0-rc4+ #23 PREEMPT(voluntary) [ 549.186476] [ C16] Hardware name: Micro-Star International Co., Ltd. MS-7E16/X670E GAMING PLUS WIFI (MS-7E16), BIOS 1.90 12/31/2024 [ 549.186478] [ C16] RIP: 0010:__pskb_pull_tail+0x3ff/0x510 [ 549.186484] [ C16] Code: 06 f0 ff 4f 34 74 7b 4d 8b 8c 24 c8 00 00 00 45 8b 84 24 c0 00 00 00 e9 c8 fd ff ff 48 c7 44 24 08 00 00 00 00 e9 5e fe ff ff <0f> 0b 31 c0 e9 23 90 5b ff 41 f7 c6 ff 0f 00 00 75 bf 49 8b 06 a8 [ 549.186487] [ C16] RSP: 0018:ffffb391c0640d70 EFLAGS: 00010282 [ 549.186490] [ C16] RAX: 00000000fffffff2 RBX: ffff8fe7e4d40200 RCX: 00000000fffffff2 [ 549.186492] [ C16] RDX: ffff8fe7c3a4bf8e RSI: 0000000000000180 RDI: ffff8fe7c3a4bf40 [ 549.186494] [ C16] RBP: ffffb391c0640da8 R08: ffff8fe7c3a4c0c0 R09: 000000000000000e [ 549.186496] [ C16] R10: ffffb391c0640d88 R11: 000000000000000e R12: ffff8fe7e4d40200 [ 549.186497] [ C16] R13: 00000000fffffff2 R14: ffff8fe7fa01a000 R15: 00000000fffffff2 [ 549.186499] [ C16] FS: 0000000000000000(0000) GS:ffff8fef5ae40000(0000) knlGS:0000000000000000 [ 549.186502] [ C16] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 549.186503] [ C16] CR2: 00007f77d81d6000 CR3: 000000051a032000 CR4: 0000000000750ef0 [ 549.186505] [ C16] PKRU: 55555554 [ 549.186507] [ C16] Call Trace: [ 549.186510] [ C16] <IRQ> [ 549.186513] [ C16] ? srso_alias_return_thunk+0x5/0xfbef5 [ 549.186517] [ C16] __skb_pad+0xc7/0xf0 [ 549.186523] [ C16] wx_clean_rx_irq+0x355/0x3b0 [libwx] [ 549.186533] [ C16] wx_poll+0x92/0x120 [libwx] [ 549.186540] [ C16] __napi_poll+0x28/0x190 [ 549.186544] [ C16] net_rx_action+0x301/0x3f0 [ 549.186548] [ C16] ? srso_alias_return_thunk+0x5/0xfbef5 [ 549.186551] [ C16] ? __raw_spin_lock_irqsave+0x1e/0x50 [ 549.186554] [ C16] ? srso_alias_return_thunk+0x5/0xfbef5 [ 549.186557] [ C16] ? wake_up_nohz_cpu+0x35/0x160 [ 549.186559] [ C16] ? srso_alias_return_thunk+0x5/0xfbef5 [ 549.186563] [ C16] handle_softirqs+0xf9/0x2c0 [ 549.186568] [ C16] __irq_exit_rcu+0xc7/0x130 [ 549.186572] [ C16] common_interrupt+0xb8/0xd0 [ 549.186576] [ C16] </IRQ> [ 549.186577] [ C16] <TASK> [ 549.186579] [ C16] asm_common_interrupt+0x22/0x40 [ 549.186582] [ C16] RIP: 0010:cpuidle_enter_state+0xc2/0x420 [ 549.186585] [ C16] Code: 00 00 e8 11 0e 5e ff e8 ac f0 ff ff 49 89 c5 0f 1f 44 00 00 31 ff e8 0d ed 5c ff 45 84 ff 0f 85 40 02 00 00 fb 0f 1f 44 00 00 <45> 85 f6 0f 88 84 01 00 00 49 63 d6 48 8d 04 52 48 8d 04 82 49 8d [ 549.186587] [ C16] RSP: 0018:ffffb391c0277e78 EFLAGS: 00000246 [ 549.186590] [ C16] RAX: ffff8fef5ae40000 RBX: 0000000000000003 RCX: 0000000000000000 [ 549.186591] [ C16] RDX: 0000007fde0faac5 RSI: ffffffff826e53f6 RDI: ffffffff826fa9b3 [ 549.186593] [ C16] RBP: ffff8fe7c3a20800 R08: 0000000000000002 R09: 0000000000000000 [ 549.186595] [ C16] R10: 0000000000000000 R11: 000000000000ffff R12: ffffffff82ed7a40 [ 549.186596] [ C16] R13: 0000007fde0faac5 R14: 0000000000000003 R15: 0000000000000000 [ 549.186601] [ C16] ? cpuidle_enter_state+0xb3/0x420 [ 549.186605] [ C16] cpuidle_en ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: iio: common: st_sensors: Fix use of uninitialize device structs Throughout the various probe functions &indio_dev->dev is used before it is initialized. This caused a kernel panic in st_sensors_power_enable() when the call to devm_regulator_bulk_get_enable() fails and then calls dev_err_probe() with the uninitialized device. This seems to only cause a panic with dev_err_probe(), dev_err(), dev_warn() and dev_info() don't seem to cause a panic, but are fixed as well. The issue is reported and traced here: [1]Show less

In the Linux kernel, the following vulnerability has been resolved: comedi: pcl812: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: if ((1 << it->options[1]) & board->irq_bits) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test. Valid `it->options[1]` values that select the IRQ will be in the range [1,15]. The value 0 explicitly disables the use of interrupts.Show less

In the Linux kernel, the following vulnerability has been resolved: comedi: aio_iiro_16: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: if ((1 << it->options[1]) & 0xdcfc) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test. Valid `it->options[1]` values that select the IRQ will be in the range [1,15]. The value 0 explicitly disables the use of interrupts.Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: Reject %p% format string in bprintf-like helpers static const char fmt[] = "%p%"; bpf_trace_printk(fmt, sizeof(fmt)); The above BPF program isn't rejected and causes a kernel warning at runtime: Please remove unsupported %\x00 in format string WARNING: CPU: 1 PID: 7244 at lib/vsprintf.c:2680 format_decode+0x49c/0x5d0 This happens because bpf_bprintf_prepare skips over the second %, detected as punctuation, while processing %p. This patch fixes it by not skipping over punctuation. %\x00 is then processed in the next iteration and rejected.Show less

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free in cifs_oplock_break A race condition can occur in cifs_oplock_break() leading to a use-after-free of the cinode structure when unmounting: cifs_oplock_break() _cifsFileInfo_put(cfile) cifsFileInfo_put_final() cifs_sb_deactive() [last ref, start releasing sb] kill_sb() kill_anon_super() generic_shutdown_super() evict_inodes() dispose_list() evict() destroy_inode() call_rcu(&inode->i_rcu, i_callback) spin_lock(&cinode->open_file_lock) <- OK [later] i_callback() cifs_free_inode() kmem_cache_free(cinode) spin_unlock(&cinode->open_file_lock) <- UAF cifs_done_oplock_break(cinode) <- UAF The issue occurs when umount has already released its reference to the superblock. When _cifsFileInfo_put() calls cifs_sb_deactive(), this releases the last reference, triggering the immediate cleanup of all inodes under RCU. However, cifs_oplock_break() continues to access the cinode after this point, resulting in use-after-free. Fix this by holding an extra reference to the superblock during the entire oplock break operation. This ensures that the superblock and its inodes remain valid until the oplock break completes.Show less

In the Linux kernel, the following vulnerability has been resolved: ice: add NULL check in eswitch lag check The function ice_lag_is_switchdev_running() is being called from outside of the LAG event handler code. This results in the lag->upper_netdev being NULL sometimes. To avoid a NULL-pointer dereference, there needs to be a check before it is dereferenced.Show less

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix irq-disabled in local_bh_enable() The rxrpc_assess_MTU_size() function calls down into the IP layer to find out the MTU size for a route. When accepting an incoming call, this is called from rxrpc_new_incoming_call() which holds interrupts disabled across the code that calls down to it. Unfortunately, the IP layer uses local_bh_enable() which, config dependent, throws a warning if IRQs are enabled: WARNING: CPU: 1 PID: 5544 at kernel/softirq.c:387 __local_bh_enable_ip+0x43/0xd0 ... RIP: 0010:__local_bh_enable_ip+0x43/0xd0 ... Call Trace: <TASK> rt_cache_route+0x7e/0xa0 rt_set_nexthop.isra.0+0x3b3/0x3f0 __mkroute_output+0x43a/0x460 ip_route_output_key_hash+0xf7/0x140 ip_route_output_flow+0x1b/0x90 rxrpc_assess_MTU_size.isra.0+0x2a0/0x590 rxrpc_new_incoming_peer+0x46/0x120 rxrpc_alloc_incoming_call+0x1b1/0x400 rxrpc_new_incoming_call+0x1da/0x5e0 rxrpc_input_packet+0x827/0x900 rxrpc_io_thread+0x403/0xb60 kthread+0x2f7/0x310 ret_from_fork+0x2a/0x230 ret_from_fork_asm+0x1a/0x30 ... hardirqs last enabled at (23): _raw_spin_unlock_irq+0x24/0x50 hardirqs last disabled at (24): _raw_read_lock_irq+0x17/0x70 softirqs last enabled at (0): copy_process+0xc61/0x2730 softirqs last disabled at (25): rt_add_uncached_list+0x3c/0x90 Fix this by moving the call to rxrpc_assess_MTU_size() out of rxrpc_init_peer() and further up the stack where it can be done without interrupts disabled. It shouldn't be a problem for rxrpc_new_incoming_call() to do it after the locks are dropped as pmtud is going to be performed by the I/O thread - and we're in the I/O thread at this point.Show less

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix recv-recv race of completed call If a call receives an event (such as incoming data), the call gets placed on the socket's queue and a thread in recvmsg can be awakened to go and process it. Once the thread has picked up the call off of the queue, further events will cause it to be requeued, and once the socket lock is dropped (recvmsg uses call->user_mutex to allow the socket to be used in parallel), a second thread can come in and its recvmsg can pop the call off the socket queue again. In such a case, the first thread will be receiving stuff from the call and the second thread will be blocked on call->user_mutex. The first thread can, at this point, process both the event that it picked call for and the event that the second thread picked the call for and may see the call terminate - in which case the call will be "released", decoupling the call from the user call ID assigned to it (RXRPC_USER_CALL_ID in the control message). The first thread will return okay, but then the second thread will wake up holding the user_mutex and, if it sees that the call has been released by the first thread, it will BUG thusly: kernel BUG at net/rxrpc/recvmsg.c:474! Fix this by just dequeuing the call and ignoring it if it is seen to be already released. We can't tell userspace about it anyway as the user call ID has become stale.Show less

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix the smbd_response slab to allow usercopy The handling of received data in the smbdirect client code involves using copy_to_iter() to copy data from the smbd_reponse struct's packet trailer to a folioq buffer provided by netfslib that encapsulates a chunk of pagecache. If, however, CONFIG_HARDENED_USERCOPY=y, this will result in the checks then performed in copy_to_iter() oopsing with something like the following: CIFS: Attempting to mount //172.31.9.1/test CIFS: VFS: RDMA transport established usercopy: Kernel memory exposure attempt detected from SLUB object 'smbd_response_0000000091e24ea1' (offset 81, size 63)! ------------[ cut here ]------------ kernel BUG at mm/usercopy.c:102! ... RIP: 0010:usercopy_abort+0x6c/0x80 ... Call Trace: <TASK> __check_heap_object+0xe3/0x120 __check_object_size+0x4dc/0x6d0 smbd_recv+0x77f/0xfe0 [cifs] cifs_readv_from_socket+0x276/0x8f0 [cifs] cifs_read_from_socket+0xcd/0x120 [cifs] cifs_demultiplex_thread+0x7e9/0x2d50 [cifs] kthread+0x396/0x830 ret_from_fork+0x2b8/0x3b0 ret_from_fork_asm+0x1a/0x30 The problem is that the smbd_response slab's packet field isn't marked as being permitted for usercopy. Fix this by passing parameters to kmem_slab_create() to indicate that copy_to_iter() is permitted from the packet region of the smbd_response slab objects, less the header space.Show less

In the Linux kernel, the following vulnerability has been resolved: sched/ext: Prevent update_locked_rq() calls with NULL rq Avoid invoking update_locked_rq() when the runqueue (rq) pointer is NULL in the SCX_CALL_OP and SCX_CALL_OP_RET macros. Previously, calling update_locked_rq(NULL) with preemption enabled could trigger the following warning: BUG: using __this_cpu_write() in preemptible [00000000] This happens because __this_cpu_write() is unsafe to use in preemptible context. rq is NULL when an ops invoked from an unlocked context. In such cases, we don't need to store any rq, since the value should already be NULL (unlocked). Ensure that update_locked_rq() is only called when rq is non-NULL, preventing calling __this_cpu_write() on preemptible context.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/imagination: Fix kernel crash when hard resetting the GPU The GPU hard reset sequence calls pm_runtime_force_suspend() and pm_runtime_force_resume(), which according to their documentation should only be used during system-wide PM transitions to sleep states. The main issue though is that depending on some internal runtime PM state as seen by pm_runtime_force_suspend() (whether the usage count is <= 1), pm_runtime_force_resume() might not resume the device unless needed. If that happens, the runtime PM resume callback pvr_power_device_resume() is not called, the GPU clocks are not re-enabled, and the kernel crashes on the next attempt to access GPU registers as part of the power-on sequence. Replace calls to pm_runtime_force_suspend() and pm_runtime_force_resume() with direct calls to the driver's runtime PM callbacks, pvr_power_device_suspend() and pvr_power_device_resume(), to ensure clocks are re-enabled and avoid the kernel crash.Show less