Linux Kernel

In the Linux kernel, the following vulnerability has been resolved: rpmsg: char: Avoid double destroy of default endpoint The rpmsg_dev_remove() in rpmsg_core is the place for releasing this default endpoint. So need to avoid destroying the default endpoint in rpmsg_chrdev_eptdev_destroy(), this should be the same as rpmsg_eptdev_release(). Otherwise there will be double destroy issue that ept->refcount report warning: refcount_t: underflow; use-after-free. Call trace: refcount_warn_saturate+0xf8/0x150 virtio_rpmsg_destroy_ept+0xd4/0xec rpmsg_dev_remove+0x60/0x70 The issue can be reproduced by stopping remoteproc before closing the /dev/rpmsgX.Show less

In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/hpre - fix resource leak in remove process In hpre_remove(), when the disable operation of qm sriov failed, the following logic should continue to be executed to release the remaining resources that have been allocated, instead of returning directly, otherwise there will be resource leakage.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix UBSAN shift-out-of-bounds warning If get_num_sdma_queues or get_num_xgmi_sdma_queues is 0, we end up doing a shift operation where the number of bits shifted equals number of bits in the operand. This behaviour is undefined. Set num_sdma_queues or num_xgmi_sdma_queues to ULLONG_MAX, if the count is >= number of bits in the operand. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1472Show less

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: ensure data length is within supported range Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer' to ensure the data length isn't within the supported range. In particular a data length of 0 is not supported by the hardware and causes unintended or destructive behaviour. This limitation becomes obvious when looking at the register documentation [1]. 4 bits are reserved for DATA_WIDTH and the value of these 4 bits is used as N + 1, allowing a data length range of 1 <= len <= 16. Affected by this is the SMBus Quick Operation which works with a data length of 0. Passing 0 as the length causes an underflow of the value due to: (len - 1) & 0xf and effectively specifying a transfer length of 16 via the registers. This causes a 16-byte write operation instead of a Quick Write. For example, on SFP modules without write-protected EEPROM this soft-bricks them by overwriting some initial bytes. For completeness, also add a quirk for the zero length. [1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2Show less

In the Linux kernel, the following vulnerability has been resolved: ceph: fix race condition validating r_parent before applying state Add validation to ensure the cached parent directory inode matches the directory info in MDS replies. This prevents client-side race conditions where concurrent operations (e.g. rename) cause r_parent to become stale between request initiation and reply processing, which could lead to applying state changes to incorrect directory inodes. [ idryomov: folded a kerneldoc fixup and a follow-up fix from Alex to move CEPH_CAP_PIN reference when r_parent is updated: When the parent directory lock is not held, req->r_parent can become stale and is updated to point to the correct inode. However, the associated CEPH_CAP_PIN reference was not being adjusted. The CEPH_CAP_PIN is a reference on an inode that is tracked for accounting purposes. Moving this pin is important to keep the accounting balanced. When the pin was not moved from the old parent to the new one, it created two problems: The reference on the old, stale parent was never released, causing a reference leak. A reference for the new parent was never acquired, creating the risk of a reference underflow later in ceph_mdsc_release_request(). This patch corrects the logic by releasing the pin from the old parent and acquiring it for the new parent when r_parent is switched. This ensures reference accounting stays balanced. ]Show less

In the Linux kernel, the following vulnerability has been resolved: genetlink: fix genl_bind() invoking bind() after -EPERM Per family bind/unbind callbacks were introduced to allow families to track multicast group consumer presence, e.g. to start or stop producing events depending on listeners. However, in genl_bind() the bind() callback was invoked even if capability checks failed and ret was set to -EPERM. This means that callbacks could run on behalf of unauthorized callers while the syscall still returned failure to user space. Fix this by only invoking bind() after "if (ret) break;" check i.e. after permission checks have succeeded.Show less

In the Linux kernel, the following vulnerability has been resolved: can: j1939: implement NETDEV_UNREGISTER notification handler syzbot is reporting unregister_netdevice: waiting for vcan0 to become free. Usage count = 2 problem, for j1939 protocol did not have NETDEV_UNREGISTER notification handler for undoing changes made by j1939_sk_bind(). Commit 25fe97cb7620 ("can: j1939: move j1939_priv_put() into sk_destruct callback") expects that a call to j1939_priv_put() can be unconditionally delayed until j1939_sk_sock_destruct() is called. But we need to call j1939_priv_put() against an extra ref held by j1939_sk_bind() call (as a part of undoing changes made by j1939_sk_bind()) as soon as NETDEV_UNREGISTER notification fires (i.e. before j1939_sk_sock_destruct() is called via j1939_sk_release()). Otherwise, the extra ref on "struct j1939_priv" held by j1939_sk_bind() call prevents "struct net_device" from dropping the usage count to 1; making it impossible for unregister_netdevice() to continue. [mkl: remove space in front of label]Show less

In the Linux kernel, the following vulnerability has been resolved: erofs: fix invalid algorithm for encoded extents The current algorithm sanity checks do not properly apply to new encoded extents. Unify the algorithm check with Z_EROFS_COMPRESSION(_RUNTIME)_MAX and ensure consistency with sbi->available_compr_algs.Show less

In the Linux kernel, the following vulnerability has been resolved: dmaengine: qcom: bam_dma: Fix DT error handling for num-channels/ees When we don't have a clock specified in the device tree, we have no way to ensure the BAM is on. This is often the case for remotely-controlled or remotely-powered BAM instances. In this case, we need to read num-channels from the DT to have all the necessary information to complete probing. However, at the moment invalid device trees without clock and without num-channels still continue probing, because the error handling is missing return statements. The driver will then later try to read the number of channels from the registers. This is unsafe, because it relies on boot firmware and lucky timing to succeed. Unfortunately, the lack of proper error handling here has been abused for several Qualcomm SoCs upstream, causing early boot crashes in several situations [1, 2]. Avoid these early crashes by erroring out when any of the required DT properties are missing. Note that this will break some of the existing DTs upstream (mainly BAM instances related to the crypto engine). However, clearly these DTs have never been tested properly, since the error in the kernel log was just ignored. It's safer to disable the crypto engine for these broken DTBs. [1]: https://lore.kernel.org/r/CY01EKQVWE36.B9X5TDXAREPF@fairphone.com/ [2]: https://lore.kernel.org/r/20230626145959.646747-1-krzysztof.kozlowski@linaro.org/Show less

In the Linux kernel, the following vulnerability has been resolved: ixgbe: fix incorrect map used in eee linkmode incorrectly used ixgbe_lp_map in loops intended to populate the supported and advertised EEE linkmode bitmaps based on ixgbe_ls_map. This results in incorrect bit setting and potential out-of-bounds access, since ixgbe_lp_map and ixgbe_ls_map have different sizes and purposes. ixgbe_lp_map[i] -> ixgbe_ls_map[i] Use ixgbe_ls_map for supported and advertised linkmodes, and keep ixgbe_lp_map usage only for link partner (lp_advertised) mapping.Show less

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: stop checking viability of op->max_freq in supports_op callback In commit 13529647743d9 ("spi: microchip-core-qspi: Support per spi-mem operation frequency switches") the logic for checking the viability of op->max_freq in mchp_coreqspi_setup_clock() was copied into mchp_coreqspi_supports_op(). Unfortunately, op->max_freq is not valid when this function is called during probe but is instead zero. Accordingly, baud_rate_val is calculated to be INT_MAX due to division by zero, causing probe of the attached memory device to fail. Seemingly spi-microchip-core-qspi was the only driver that had such a modification made to its supports_op callback when the per_op_freq capability was added, so just remove it to restore prior functionality.Show less

In the Linux kernel, the following vulnerability has been resolved: pcmcia: Add error handling for add_interval() in do_validate_mem() In the do_validate_mem(), the call to add_interval() does not handle errors. If kmalloc() fails in add_interval(), it could result in a null pointer being inserted into the linked list, leading to illegal memory access when sub_interval() is called next. This patch adds an error handling for the add_interval(). If add_interval() returns an error, the function will return early with the error code.Show less

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: add missing check for rx wcid entries Non-station wcid entries must not be passed to the rx functions. In case of the global wcid entry, it could even lead to corruption in the wcid array due to pointer being casted to struct mt7996_sta_link using container_of.Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix out-of-bounds dynptr write in bpf_crypto_crypt Stanislav reported that in bpf_crypto_crypt() the destination dynptr's size is not validated to be at least as large as the source dynptr's size before calling into the crypto backend with 'len = src_len'. This can result in an OOB write when the destination is smaller than the source. Concretely, in mentioned function, psrc and pdst are both linear buffers fetched from each dynptr: psrc = __bpf_dynptr_data(src, src_len); [...] pdst = __bpf_dynptr_data_rw(dst, dst_len); [...] err = decrypt ? ctx->type->decrypt(ctx->tfm, psrc, pdst, src_len, piv) : ctx->type->encrypt(ctx->tfm, psrc, pdst, src_len, piv); The crypto backend expects pdst to be large enough with a src_len length that can be written. Add an additional src_len > dst_len check and bail out if it's the case. Note that these kfuncs are accessible under root privileges only.Show less

In the Linux kernel, the following vulnerability has been resolved: mm/damon/reclaim: avoid divide-by-zero in damon_reclaim_apply_parameters() When creating a new scheme of DAMON_RECLAIM, the calculation of 'min_age_region' uses 'aggr_interval' as the divisor, which may lead to division-by-zero errors. Fix it by directly returning -EINVAL when such a case occurs.Show less

In the Linux kernel, the following vulnerability has been resolved: net: phy: transfer phy_config_inband() locking responsibility to phylink Problem description =================== Lockdep reports a possible circular locking dependency (AB/BA) between &pl->state_mutex and &phy->lock, as follows. phylink_resolve() // acquires &pl->state_mutex -> phylink_major_config() -> phy_config_inband() // acquires &pl->phydev->lock whereas all the other call sites where &pl->state_mutex and &pl->phydev->lock have the locking scheme reversed. Everywhere else, &pl->phydev->lock is acquired at the top level, and &pl->state_mutex at the lower level. A clear example is phylink_bringup_phy(). The outlier is the newly introduced phy_config_inband() and the existing lock order is the correct one. To understand why it cannot be the other way around, it is sufficient to consider phylink_phy_change(), phylink's callback from the PHY device's phy->phy_link_change() virtual method, invoked by the PHY state machine. phy_link_up() and phy_link_down(), the (indirect) callers of phylink_phy_change(), are called with &phydev->lock acquired. Then phylink_phy_change() acquires its own &pl->state_mutex, to serialize changes made to its pl->phy_state and pl->link_config. So all other instances of &pl->state_mutex and &phydev->lock must be consistent with this order. Problem impact ============== I think the kernel runs a serious deadlock risk if an existing phylink_resolve() thread, which results in a phy_config_inband() call, is concurrent with a phy_link_up() or phy_link_down() call, which will deadlock on &pl->state_mutex in phylink_phy_change(). Practically speaking, the impact may be limited by the slow speed of the medium auto-negotiation protocol, which makes it unlikely for the current state to still be unresolved when a new one is detected, but I think the problem is there. Nonetheless, the problem was discovered using lockdep. Proposed solution ================= Practically speaking, the phy_config_inband() requirement of having phydev->lock acquired must transfer to the caller (phylink is the only caller). There, it must bubble up until immediately before &pl->state_mutex is acquired, for the cases where that takes place. Solution details, considerations, notes ======================================= This is the phy_config_inband() call graph: sfp_upstream_ops :: connect_phy() | v phylink_sfp_connect_phy() | v phylink_sfp_config_phy() | | sfp_upstream_ops :: module_insert() | | | v | phylink_sfp_module_insert() | | | | sfp_upstream_ops :: module_start() | | | | | v | | phylink_sfp_module_start() | | | | v v | phylink_sfp_config_optical() phylink_start() | | | phylink_resume() v v | | phylink_sfp_set_config() | | | v v v phylink_mac_initial_config() | phylink_resolve() | | phylink_ethtool_ksettings_set() v v v phylink_major_config() | v phy_config_inband() phylink_major_config() caller #1, phylink_mac_initial_config(), does not acquire &pl->state_mutex nor do its callers. It must acquire &pl->phydev->lock prior to calling phylink_major_config(). phylink_major_config() caller #2, phylink_resolve() acquires &pl->state_mutex, thus also needs to acquire &pl->phydev->lock. phylink_major_config() caller #3, phylink_ethtool_ksettings_set(), is completely uninteresting, because it only call ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: tracing: Silence warning when chunk allocation fails in trace_pid_write Syzkaller trigger a fault injection warning: WARNING: CPU: 1 PID: 12326 at tracepoint_add_func+0xbfc/0xeb0 Modules linked in: CPU: 1 UID: 0 PID: 12326 Comm: syz.6.10325 Tainted: G U 6.14.0-rc5-syzkaller #0 Tainted: [U]=USER Hardware name: Google Compute Engine/Google Compute Engine RIP: 0010:tracepoint_add_func+0xbfc/0xeb0 kernel/tracepoint.c:294 Code: 09 fe ff 90 0f 0b 90 0f b6 74 24 43 31 ff 41 bc ea ff ff ff RSP: 0018:ffffc9000414fb48 EFLAGS: 00010283 RAX: 00000000000012a1 RBX: ffffffff8e240ae0 RCX: ffffc90014b78000 RDX: 0000000000080000 RSI: ffffffff81bbd78b RDI: 0000000000000001 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffffffffffffffef R13: 0000000000000000 R14: dffffc0000000000 R15: ffffffff81c264f0 FS: 00007f27217f66c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2e80dff8 CR3: 00000000268f8000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tracepoint_probe_register_prio+0xc0/0x110 kernel/tracepoint.c:464 register_trace_prio_sched_switch include/trace/events/sched.h:222 [inline] register_pid_events kernel/trace/trace_events.c:2354 [inline] event_pid_write.isra.0+0x439/0x7a0 kernel/trace/trace_events.c:2425 vfs_write+0x24c/0x1150 fs/read_write.c:677 ksys_write+0x12b/0x250 fs/read_write.c:731 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f We can reproduce the warning by following the steps below: 1. echo 8 >> set_event_notrace_pid. Let tr->filtered_pids owns one pid and register sched_switch tracepoint. 2. echo ' ' >> set_event_pid, and perform fault injection during chunk allocation of trace_pid_list_alloc. Let pid_list with no pid and assign to tr->filtered_pids. 3. echo ' ' >> set_event_pid. Let pid_list is NULL and assign to tr->filtered_pids. 4. echo 9 >> set_event_pid, will trigger the double register sched_switch tracepoint warning. The reason is that syzkaller injects a fault into the chunk allocation in trace_pid_list_alloc, causing a failure in trace_pid_list_set, which may trigger double register of the same tracepoint. This only occurs when the system is about to crash, but to suppress this warning, let's add failure handling logic to trace_pid_list_set.Show less

In the Linux kernel, the following vulnerability has been resolved: tcp_bpf: Call sk_msg_free() when tcp_bpf_send_verdict() fails to allocate psock->cork. syzbot reported the splat below. [0] The repro does the following: 1. Load a sk_msg prog that calls bpf_msg_cork_bytes(msg, cork_bytes) 2. Attach the prog to a SOCKMAP 3. Add a socket to the SOCKMAP 4. Activate fault injection 5. Send data less than cork_bytes At 5., the data is carried over to the next sendmsg() as it is smaller than the cork_bytes specified by bpf_msg_cork_bytes(). Then, tcp_bpf_send_verdict() tries to allocate psock->cork to hold the data, but this fails silently due to fault injection + __GFP_NOWARN. If the allocation fails, we need to revert the sk->sk_forward_alloc change done by sk_msg_alloc(). Let's call sk_msg_free() when tcp_bpf_send_verdict fails to allocate psock->cork. The "*copied" also needs to be updated such that a proper error can be returned to the caller, sendmsg. It fails to allocate psock->cork. Nothing has been corked so far, so this patch simply sets "*copied" to 0. [0]: WARNING: net/ipv4/af_inet.c:156 at inet_sock_destruct+0x623/0x730 net/ipv4/af_inet.c:156, CPU#1: syz-executor/5983 Modules linked in: CPU: 1 UID: 0 PID: 5983 Comm: syz-executor Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:inet_sock_destruct+0x623/0x730 net/ipv4/af_inet.c:156 Code: 0f 0b 90 e9 62 fe ff ff e8 7a db b5 f7 90 0f 0b 90 e9 95 fe ff ff e8 6c db b5 f7 90 0f 0b 90 e9 bb fe ff ff e8 5e db b5 f7 90 <0f> 0b 90 e9 e1 fe ff ff 89 f9 80 e1 07 80 c1 03 38 c1 0f 8c 9f fc RSP: 0018:ffffc90000a08b48 EFLAGS: 00010246 RAX: ffffffff8a09d0b2 RBX: dffffc0000000000 RCX: ffff888024a23c80 RDX: 0000000000000100 RSI: 0000000000000fff RDI: 0000000000000000 RBP: 0000000000000fff R08: ffff88807e07c627 R09: 1ffff1100fc0f8c4 R10: dffffc0000000000 R11: ffffed100fc0f8c5 R12: ffff88807e07c380 R13: dffffc0000000000 R14: ffff88807e07c60c R15: 1ffff1100fc0f872 FS: 00005555604c4500(0000) GS:ffff888125af1000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005555604df5c8 CR3: 0000000032b06000 CR4: 00000000003526f0 Call Trace: <IRQ> __sk_destruct+0x86/0x660 net/core/sock.c:2339 rcu_do_batch kernel/rcu/tree.c:2605 [inline] rcu_core+0xca8/0x1770 kernel/rcu/tree.c:2861 handle_softirqs+0x286/0x870 kernel/softirq.c:579 __do_softirq kernel/softirq.c:613 [inline] invoke_softirq kernel/softirq.c:453 [inline] __irq_exit_rcu+0xca/0x1f0 kernel/softirq.c:680 irq_exit_rcu+0x9/0x30 kernel/softirq.c:696 instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1052 [inline] sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1052 </IRQ>Show less

In the Linux kernel, the following vulnerability has been resolved: nfs/localio: restore creds before releasing pageio data Otherwise if the nfsd filecache code releases the nfsd_file immediately, it can trigger the BUG_ON(cred == current->cred) in __put_cred() when it puts the nfsd_file->nf_file->f-cred.Show less