Ios

A vulnerability in the implementation of Network Address Translation (NAT) functionality in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to the improper translation of H.323 messages that use the Registration, Admission, and Status (RAS) protocol and are sent to an affected device via IPv4 packets. An attacker could exploit this vulnerability by sending a crafted H.323 RAS packet through an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition. This vulnerability affects Cisco devices that are configured to use an application layer gateway with NAT (NAT ALG) for H.323 RAS messages. By default, a NAT ALG is enabled for H.323 RAS messages. Cisco Bug IDs: CSCvc57217.Show less

A vulnerability in the Cisco Network Plug and Play application of Cisco IOS 12.4 through 15.6 and Cisco IOS XE 3.3 through 16.4 could allow an unauthenticated, remote attacker to gain unauthorized access to sensitive data by using an invalid certificate. The vulnerability is due to insufficient certificate validation by the affected software. An attacker could exploit this vulnerability by supplying a crafted certificate to an affected device. A successful exploit could allow the attacker to conduct man-in-the-middle attacks to decrypt confidential information on user connections to the affected software. Cisco Bug IDs: CSCvc33171.Show less

The encryption library in Cisco IOS Software 15.2(1)T, 15.2(1)T1, and 15.2(2)T, Cisco NX-OS in Cisco MDS 9222i Multiservice Modular Switch, Cisco MDS 9000 18/4-Port Multiservice Module, and Cisco MDS 9000 Storage Services Node module before 5.2(6), and Cisco IOS in Cisco VPN Services Port Adaptor for Catalyst 6500 12.2(33)SXI, and 12.2(33)SXJ when IP Security (aka IPSec) is used, allows remote attackers to obtain unencrypted packets from encrypted sessions.Show less

A vulnerability in the UDP processing code of Cisco IOS 15.1, 15.2, and 15.4 and IOS XE 3.14 through 3.18 could allow an unauthenticated, remote attacker to cause the input queue of an affected system to hold UDP packets, causing an interface queue wedge and a denial of service (DoS) condition. The vulnerability is due to Cisco IOS Software application changes that create UDP sockets and leave the sockets idle without closing them. An attacker could exploit this vulnerability by sending UDP packets with a destination port of 0 to an affected device. A successful exploit could allow the attacker to cause UDP packets to be held in the input interfaces queue, resulting in a DoS condition. The input interface queue will stop holding UDP packets when it receives 250 packets. Cisco Bug IDs: CSCup10024, CSCva55744, CSCva95506.Show less

A vulnerability in the IPv6 Simple Network Management Protocol (SNMP) code of Cisco IOS and Cisco IOS XE Software could allow an authenticated, remote attacker to cause high CPU usage or a reload of the device. The vulnerability is due to IPv6 sub block corruption. An attacker could exploit this vulnerability by polling the affected device IPv6 information. An exploit could allow the attacker to trigger high CPU usage or a reload of the device. Known Affected Releases: Denali-16.3.1. Cisco Bug IDs: CSCvb14640.Show less

Cisco IOS 12.0 through 15.6, Adaptive Security Appliance (ASA) Software 7.0.1 through 9.7.1.2, NX-OS 4.0 through 12.0, and IOS XE 3.6 through 3.18 are affected by a vulnerability involving the Open Shortest Path First (OSPF) Routing Protocol Link State Advertisement (LSA) database. This vulnerability could allow an unauthenticated, remote attacker to take full control of the OSPF Autonomous System (AS) domain routing table, allowing the attacker to intercept or black-hole traffic. The attacker could exploit this vulnerability by injecting crafted OSPF packets. Successful exploitation could cause the targeted router to flush its routing table and propagate the crafted OSPF LSA type 1 update throughout the OSPF AS domain. To exploit this vulnerability, an attacker must accurately determine certain parameters within the LSA database on the target router. This vulnerability can only be triggered by sending crafted unicast or multicast OSPF LSA type 1 packets. No other LSA type packets can trigger this vulnerability. OSPFv3 is not affected by this vulnerability. Fabric Shortest Path First (FSPF) protocol is not affected by this vulnerability. Cisco Bug IDs: CSCva74756, CSCve47393, CSCve47401.Show less

A vulnerability in the Autonomic Networking feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to reset the Autonomic Control Plane (ACP) of an affected system and view ACP packets that are transferred in clear text within an affected system, an Information Disclosure Vulnerability. More Information: CSCvd51214. Known Affected Releases: Denali-16.2.1 Denali-16.3.1.Show less

A vulnerability in the Autonomic Networking feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, adjacent attacker to cause autonomic nodes of an affected system to reload, resulting in a denial of service (DoS) condition. More Information: CSCvd88936. Known Affected Releases: Denali-16.2.1 Denali-16.3.1.Show less

Cisco IOS before 15.2(4)S6 does not initialize an unspecified variable, which might allow remote authenticated users to cause a denial of service (CPU consumption, watchdog timeout, crash) by walking specific SNMP objects.Show less

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.Show less

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.Show less

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.Show less

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.Show less

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.Show less

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.Show less

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.Show less

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.Show less

A vulnerability in Cisco IOS 15.5(3)M Software for Cisco CallManager Express (CME) could allow an unauthenticated, remote attacker to make unauthorized phone calls. The vulnerability is due to a configuration restriction in the toll-fraud protections component of the affected software. An attacker could exploit this vulnerability to place unauthorized, long-distance phone calls by using an affected system. Cisco Bug IDs: CSCuy40939.Show less