Improper Check for Unusual or Exceptional Conditions

An Improper Check for Unusual or Exceptional Conditions vulnerability in the chassis control daemon (chassisd) of Juniper Networks Junos OS on SRX1600, SRX2300 and SRX4300 allows a local attacker with low privileges to cause a complete Denial of Service (DoS). When a specific 'show chassis' CLI command is executed, chassisd crashes and restarts which causes a momentary impact to all traffic until all modules are online again. This issue affects Junos OS on SRX1600, SRX2300 and SRX4300: * 24.4 versions before 24.4R1-S3, 24.4R2. This issue does not affect Junos OS versions before 24.4R1.Show less

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on specific EX and QFX Series devices allow an unauthenticated, adjacent attacker to cause a complete Denial of Service (DoS). On EX4k, and QFX5k platforms configured as service-provider edge devices, if L2PT is enabled on the UNI and VSTP is enabled on NNI in VXLAN scenarios, receiving VSTP BPDUs on UNI leads to packet buffer allocation failures, resulting in the device to not pass traffic anymore until it is manually recovered with a restart.This issue affects Junos OS: * 24.4 releases before 24.4R2, * 25.2 releases before 25.2R1-S1, 25.2R2. This issue does not affect Junos OS releases before 24.4R1.Show less

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to bypass the configured firewall filter and access the control-plane of the device. On MX platforms with MPC10, MPC11, LC4800 or LC9600 line cards, and MX304, firewall filters applied on a loopback interface lo0.n (where n is a non-0 number) don't get executed when lo0.n is in the global VRF / default routing-instance. An affected configuration would be: user@host# show configuration interfaces lo0 | display set set interfaces lo0 unit 1 family inet filter input <filter-name> where a firewall filter is applied to a non-0 loopback interface, but that loopback interface is not referred to in any routing-instance (RI) configuration, which implies that it's used in the default RI. The issue can be observed with the CLI command: user@device> show firewall counter filter <filter_name> not showing any matches. This issue affects Junos OS on MX Series: * all versions before 23.2R2-S6, * 23.4 versions before 23.4R2-S7, * 24.2 versions before 24.2R2, * 24.4 versions before 24.4R2.Show less

BSV Ruby SDK is the Ruby SDK for the BSV blockchain. From 0.1.0 to before 0.8.2, BSV::Network::ARC's failure detection only recognises REJECTED and DOUBLE_SPEND_ATTEMPTED. ARC responses with txStatus values of INVALID, MALFORMED, MINED_IN_STALE_BLOCK, or any ORPHAN-containing extraInfo / txStatus are silently treated as successful broadcasts. Applications that gate actions on broadcaster success are tricked into trusting transactions that were never accepted by the network. This vulnerability is fixed in 0.8.2.Show less

Issue summary: Applications using RSASVE key encapsulation to establish a secret encryption key can send contents of an uninitialized memory buffer to a malicious peer. Impact summary: The uninitialized buffer might contain sensitive data from the previous execution of the application process which leads to sensitive data leakage to an attacker. RSA_public_encrypt() returns the number of bytes written on success and -1 on error. The affected code tests only whether the return value is non-zero. As a result, if RSA encryption fails, encapsulation can still return success to the caller, set the output lengths, and leave the caller to use the contents of the ciphertext buffer as if a valid KEM ciphertext had been produced. If applications use EVP_PKEY_encapsulate() with RSA/RSASVE on an attacker-supplied invalid RSA public key without first validating that key, then this may cause stale or uninitialized contents of the caller-provided ciphertext buffer to be disclosed to the attacker in place of the KEM ciphertext. As a workaround calling EVP_PKEY_public_check() or EVP_PKEY_public_check_quick() before EVP_PKEY_encapsulate() will mitigate the issue. The FIPS modules in 3.6, 3.5, 3.4, 3.3, 3.1 and 3.0 are affected by this issue.Show less

Cosign provides code signing and transparency for containers and binaries. Prior to 3.0.6 and 2.6.3, cosign verify-blob-attestation may erroneously report a "Verified OK" result for attestations with malformed payloads or mismatched predicate types. For old-format bundles and detached signatures, this was due to a logic flaw in the error handling of the predicate type validation. For new-format bundles, the predicate type validation was bypassed completely. This vulnerability is fixed in 3.0.6 and 2.6.3.Show less

A regression in the way hashes were calculated caused rules containing the address range syntax (x.x.x.x - y.y.y.y) that only differ in the address range(s) involved to be silently dropped as duplicates. Only the first of such rules is actually loaded into pf. Ranges expressed using the address[/mask-bits] syntax were not affected. Some keywords representing actions taken on a packet-matching rule, such as 'log', 'return tll', or 'dnpipe', may suffer from the same issue. It is unlikely that users have such configurations, as these rules would always be redundant. Affected rules are silently ignored, which can lead to unexpected behaviour including over- and underblocking.Show less

Handlebars provides the power necessary to let users build semantic templates. In versions 4.0.0 through 4.7.8, when a Handlebars template contains decorator syntax referencing an unregistered decorator (e.g. `{{*n}}`), the compiled template calls `lookupProperty(decorators, "n")`, which returns `undefined`. The runtime then immediately invokes the result as a function, causing an unhandled `TypeError: ... is not a function` that crashes the Node.js process. Any application that compiles user-supplied templates without wrapping the call in a `try/catch` is vulnerable to a single-request Denial of Service. Version 4.7.9 fixes the issue. Some workarounds are available. Wrap compilation and rendering in `try/catch`. Validate template input before passing it to `compile()`; reject templates containing decorator syntax (`{{*...}}`) if decorators are not used in your application. Use the pre-compilation workflow; compile templates at build time and serve only pre-compiled templates; do not call `compile()` at request time.Show less

Mattermost Plugins versions <=11.4 10.11.11.0 fail to validate webhook request timestamps which allows an attacker to corrupt Zoom meeting state in Mattermost via replayed webhook requests. Mattermost Advisory ID: MMSA-2026-00584Show less

Mattermost versions 11.4.x <= 11.4.0, 11.3.x <= 11.3.1, 11.2.x <= 11.2.3, 10.11.x <= 10.11.11 fail to prevent rendering of external SVGs on link embeds which allows unauthenticated users to crash the Mattermost webapp and desktop app via creating an issue or PR on GitHub.. Mattermost Advisory ID: MMSA-2026-00595Show less