Improper Locking

In the Linux kernel, the following vulnerability has been resolved: net: mscc: ocelot: add missing lock protection in ocelot_port_xmit_inj() ocelot_port_xmit_inj() calls ocelot_can_inject() and ocelot_port_inject_frame() without holding the injection group lock. Both functions contain lockdep_assert_held() for the injection lock, and the correct caller felix_port_deferred_xmit() properly acquires the lock using ocelot_lock_inj_grp() before calling these functions. Add ocelot_lock_inj_grp()/ocelot_unlock_inj_grp() around the register injection path to fix the missing lock protection. The FDMA path is not affected as it uses its own locking mechanism.Show less

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: fix deadlock in ni_read_folio_cmpr Syzbot reported a task hung in ni_readpage_cmpr (now ni_read_folio_cmpr). This is caused by a lock inversion deadlock involving the inode mutex (ni_lock) and page locks. Scenario: 1. Task A enters ntfs_read_folio() for page X. It acquires ni_lock. 2. Task A calls ni_read_folio_cmpr(), which attempts to lock all pages in the compressed frame (including page Y). 3. Concurrently, Task B (e.g., via readahead) has locked page Y and calls ntfs_read_folio(). 4. Task B waits for ni_lock (held by A). 5. Task A waits for page Y lock (held by B). -> DEADLOCK. The fix is to restructure locking: do not take ni_lock in ntfs_read_folio(). Instead, acquire ni_lock inside ni_read_folio_cmpr() ONLY AFTER all required page locks for the frame have been successfully acquired. This restores the correct lock ordering (Page Lock -> ni_lock) consistent with VFS. [almaz.alexandrovich@paragon-software.com: ni_readpage_cmpr was renamed to ni_read_folio_cmpr]Show less

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix deadlock between devlink lock and esw->wq esw->work_queue executes esw_functions_changed_event_handler -> esw_vfs_changed_event_handler and acquires the devlink lock. .eswitch_mode_set (acquires devlink lock in devlink_nl_pre_doit) -> mlx5_devlink_eswitch_mode_set -> mlx5_eswitch_disable_locked -> mlx5_eswitch_event_handler_unregister -> flush_workqueue deadlocks when esw_vfs_changed_event_handler executes. Fix that by no longer flushing the work to avoid the deadlock, and using a generation counter to keep track of work relevance. This avoids an old handler manipulating an esw that has undergone one or more mode changes: - the counter is incremented in mlx5_eswitch_event_handler_unregister. - the counter is read and passed to the ephemeral mlx5_host_work struct. - the work handler takes the devlink lock and bails out if the current generation is different than the one it was scheduled to operate on. - mlx5_eswitch_cleanup does the final draining before destroying the wq. No longer flushing the workqueue has the side effect of maybe no longer cancelling pending vport_change_handler work items, but that's ok since those are disabled elsewhere: - mlx5_eswitch_disable_locked disables the vport eq notifier. - mlx5_esw_vport_disable disarms the HW EQ notification and marks vport->enabled under state_lock to false to prevent pending vport handler from doing anything. - mlx5_eswitch_cleanup destroys the workqueue and makes sure all events are disabled/finished.Show less

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix runtime suspend deadlock when there is pending job The runtime suspend callback drains the running job workqueue before suspending the device. If a job is still executing and calls pm_runtime_resume_and_get(), it can deadlock with the runtime suspend path. Fix this by moving pm_runtime_resume_and_get() from the job execution routine to the job submission routine, ensuring the device is resumed before the job is queued and avoiding the deadlock during runtime suspend.Show less

In the Linux kernel, the following vulnerability has been resolved: mm: Fix a hmm_range_fault() livelock / starvation problem If hmm_range_fault() fails a folio_trylock() in do_swap_page, trying to acquire the lock of a device-private folio for migration, to ram, the function will spin until it succeeds grabbing the lock. However, if the process holding the lock is depending on a work item to be completed, which is scheduled on the same CPU as the spinning hmm_range_fault(), that work item might be starved and we end up in a livelock / starvation situation which is never resolved. This can happen, for example if the process holding the device-private folio lock is stuck in migrate_device_unmap()->lru_add_drain_all() sinc lru_add_drain_all() requires a short work-item to be run on all online cpus to complete. A prerequisite for this to happen is: a) Both zone device and system memory folios are considered in migrate_device_unmap(), so that there is a reason to call lru_add_drain_all() for a system memory folio while a folio lock is held on a zone device folio. b) The zone device folio has an initial mapcount > 1 which causes at least one migration PTE entry insertion to be deferred to try_to_migrate(), which can happen after the call to lru_add_drain_all(). c) No or voluntary only preemption. This all seems pretty unlikely to happen, but indeed is hit by the "xe_exec_system_allocator" igt test. Resolve this by waiting for the folio to be unlocked if the folio_trylock() fails in do_swap_page(). Rename migration_entry_wait_on_locked() to softleaf_entry_wait_unlock() and update its documentation to indicate the new use-case. Future code improvements might consider moving the lru_add_drain_all() call in migrate_device_unmap() to be called *after* all pages have migration entries inserted. That would eliminate also b) above. v2: - Instead of a cond_resched() in hmm_range_fault(), eliminate the problem by waiting for the folio to be unlocked in do_swap_page() (Alistair Popple, Andrew Morton) v3: - Add a stub migration_entry_wait_on_locked() for the !CONFIG_MIGRATION case. (Kernel Test Robot) v4: - Rename migrate_entry_wait_on_locked() to softleaf_entry_wait_on_locked() and update docs (Alistair Popple) v5: - Add a WARN_ON_ONCE() for the !CONFIG_MIGRATION version of softleaf_entry_wait_on_locked(). - Modify wording around function names in the commit message (Andrew Morton) (cherry picked from commit a69d1ab971a624c6f112cea61536569d579c3215)Show less

In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid double-rtnl_lock ELP metric worker batadv_v_elp_get_throughput() might be called when the RTNL lock is already held. This could be problematic when the work queue item is cancelled via cancel_delayed_work_sync() in batadv_v_elp_iface_disable(). In this case, an rtnl_lock() would cause a deadlock. To avoid this, rtnl_trylock() was used in this function to skip the retrieval of the ethtool information in case the RTNL lock was already held. But for cfg80211 interfaces, batadv_get_real_netdev() was called - which also uses rtnl_lock(). The approach for __ethtool_get_link_ksettings() must also be used instead and the lockless version __batadv_get_real_netdev() has to be called.Show less

In the Linux kernel, the following vulnerability has been resolved: USB: dummy-hcd: Fix locking/synchronization error Syzbot testing was able to provoke an addressing exception and crash in the usb_gadget_udc_reset() routine in drivers/usb/gadgets/udc/core.c, resulting from the fact that the routine was called with a second ("driver") argument of NULL. The bad caller was set_link_state() in dummy_hcd.c, and the problem arose because of a race between a USB reset and driver unbind. These sorts of races were not supposed to be possible; commit 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change"), along with a few followup commits, was written specifically to prevent them. As it turns out, there are (at least) two errors remaining in the code. Another patch will address the second error; this one is concerned with the first. The error responsible for the syzbot crash occurred because the stop_activity() routine will sometimes drop and then re-acquire the dum->lock spinlock. A call to stop_activity() occurs in set_link_state() when handling an emulated USB reset, after the test of dum->ints_enabled and before the increment of dum->callback_usage. This allowed another thread (doing a driver unbind) to sneak in and grab the spinlock, and then clear dum->ints_enabled and dum->driver. Normally this other thread would have to wait for dum->callback_usage to go down to 0 before it would clear dum->driver, but in this case it didn't have to wait since dum->callback_usage had not yet been incremented. The fix is to increment dum->callback_usage _before_ calling stop_activity() instead of after. Then the thread doing the unbind will not clear dum->driver until after the call to usb_gadget_udc_reset() safely returns and dum->callback_usage has been decremented again.Show less

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix SCX_KICK_WAIT deadlock by deferring wait to balance callback SCX_KICK_WAIT busy-waits in kick_cpus_irq_workfn() using smp_cond_load_acquire() until the target CPU's kick_sync advances. Because the irq_work runs in hardirq context, the waiting CPU cannot reschedule and its own kick_sync never advances. If multiple CPUs form a wait cycle, all CPUs deadlock. Replace the busy-wait in kick_cpus_irq_workfn() with resched_curr() to force the CPU through do_pick_task_scx(), which queues a balance callback to perform the wait. The balance callback drops the rq lock and enables IRQs following the sched_core_balance() pattern, so the CPU can process IPIs while waiting. The local CPU's kick_sync is advanced on entry to do_pick_task_scx() and continuously during the wait, ensuring any CPU that starts waiting for us sees the advancement and cannot form cyclic dependencies.Show less

In the Linux kernel, the following vulnerability has been resolved: spi: spidev: fix lock inversion between spi_lock and buf_lock The spidev driver previously used two mutexes, spi_lock and buf_lock, but acquired them in different orders depending on the code path: write()/read(): buf_lock -> spi_lock ioctl(): spi_lock -> buf_lock This AB-BA locking pattern triggers lockdep warnings and can cause real deadlocks: WARNING: possible circular locking dependency detected spidev_ioctl() -> mutex_lock(&spidev->buf_lock) spidev_sync_write() -> mutex_lock(&spidev->spi_lock) *** DEADLOCK *** The issue is reproducible with a simple userspace program that performs write() and SPI_IOC_WR_MAX_SPEED_HZ ioctl() calls from separate threads on the same spidev file descriptor. Fix this by simplifying the locking model and removing the lock inversion entirely. spidev_sync() no longer performs any locking, and all callers serialize access using spi_lock. buf_lock is removed since its functionality is fully covered by spi_lock, eliminating the possibility of lock ordering issues. This removes the lock inversion and prevents deadlocks without changing userspace ABI or behaviour.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix mismatched unlock for DMUB HW lock in HWSS fast path [Why] The evaluation for whether we need to use the DMUB HW lock isn't the same as whether we need to unlock which results in a hang when the fast path is used for ASIC without FAMS support. [How] Store a flag that indicates whether we should use the lock and use that same flag to specify whether unlocking is needed.Show less

In the Linux kernel, the following vulnerability has been resolved: octeontx2-af: Workaround SQM/PSE stalls by disabling sticky NIX SQ manager sticky mode is known to cause stalls when multiple SQs share an SMQ and transmit concurrently. Additionally, PSE may deadlock on transitions between sticky and non-sticky transmissions. There is also a credit drop issue observed when certain condition clocks are gated. work around these hardware errata by: - Disabling SQM sticky operation: - Clear TM6 (bit 15) - Clear TM11 (bit 14) - Disabling sticky → non-sticky transition path that can deadlock PSE: - Clear TM5 (bit 23) - Preventing credit drops by keeping the control-flow clock enabled: - Set TM9 (bit 21) These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this configuration the SQM/PSE maintain forward progress under load without credit loss, at the cost of disabling sticky optimizations.Show less

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: move wait_on_sem() out of spinlock With iommu.strict=1, the existing completion wait path can cause soft lockups under stressed environment, as wait_on_sem() busy-waits under the spinlock with interrupts disabled. Move the completion wait in iommu_completion_wait() out of the spinlock. wait_on_sem() only polls the hardware-updated cmd_sem and does not require iommu->lock, so holding the lock during the busy wait unnecessarily increases contention and extends the time with interrupts disabled.Show less

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: in-kernel: always set ID as avail when rm endp Syzkaller managed to find a combination of actions that was generating this warning: WARNING: net/mptcp/pm_kernel.c:1074 at __mark_subflow_endp_available net/mptcp/pm_kernel.c:1074 [inline], CPU#1: syz.7.48/2535 WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_fullmesh net/mptcp/pm_kernel.c:1446 [inline], CPU#1: syz.7.48/2535 WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_set_flags_all net/mptcp/pm_kernel.c:1474 [inline], CPU#1: syz.7.48/2535 WARNING: net/mptcp/pm_kernel.c:1074 at mptcp_pm_nl_set_flags+0x5de/0x640 net/mptcp/pm_kernel.c:1538, CPU#1: syz.7.48/2535 Modules linked in: CPU: 1 UID: 0 PID: 2535 Comm: syz.7.48 Not tainted 6.18.0-03987-gea5f5e676cf5 #17 PREEMPT(voluntary) Hardware name: QEMU Ubuntu 25.10 PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014 RIP: 0010:__mark_subflow_endp_available net/mptcp/pm_kernel.c:1074 [inline] RIP: 0010:mptcp_pm_nl_fullmesh net/mptcp/pm_kernel.c:1446 [inline] RIP: 0010:mptcp_pm_nl_set_flags_all net/mptcp/pm_kernel.c:1474 [inline] RIP: 0010:mptcp_pm_nl_set_flags+0x5de/0x640 net/mptcp/pm_kernel.c:1538 Code: 89 c7 e8 c5 8c 73 fe e9 f7 fd ff ff 49 83 ef 80 e8 b7 8c 73 fe 4c 89 ff be 03 00 00 00 e8 4a 29 e3 fe eb ac e8 a3 8c 73 fe 90 <0f> 0b 90 e9 3d ff ff ff e8 95 8c 73 fe b8 a1 ff ff ff eb 1a e8 89 RSP: 0018:ffffc9001535b820 EFLAGS: 00010287 netdevsim0: tun_chr_ioctl cmd 1074025677 RAX: ffffffff82da294d RBX: 0000000000000001 RCX: 0000000000080000 RDX: ffffc900096d0000 RSI: 00000000000006d6 RDI: 00000000000006d7 netdevsim0: linktype set to 823 RBP: ffff88802cdb2240 R08: 00000000000104ae R09: ffffffffffffffff R10: ffffffff82da27d4 R11: 0000000000000000 R12: 0000000000000000 R13: ffff88801246d8c0 R14: ffffc9001535b8b8 R15: ffff88802cdb1800 FS: 00007fc6ac5a76c0(0000) GS:ffff8880f90c8000(0000) knlGS:0000000000000000 netlink: 'syz.3.50': attribute type 5 has an invalid length. CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 netlink: 1232 bytes leftover after parsing attributes in process `syz.3.50'. CR2: 0000200000010000 CR3: 0000000025b1a000 CR4: 0000000000350ef0 Call Trace: <TASK> mptcp_pm_set_flags net/mptcp/pm_netlink.c:277 [inline] mptcp_pm_nl_set_flags_doit+0x1d7/0x210 net/mptcp/pm_netlink.c:282 genl_family_rcv_msg_doit+0x117/0x180 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x3a8/0x3f0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x16d/0x240 net/netlink/af_netlink.c:2550 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x3e9/0x4c0 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x4ab/0x5b0 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:718 [inline] __sock_sendmsg+0xc9/0xf0 net/socket.c:733 ____sys_sendmsg+0x272/0x3b0 net/socket.c:2608 ___sys_sendmsg+0x2de/0x320 net/socket.c:2662 __sys_sendmsg net/socket.c:2694 [inline] __do_sys_sendmsg net/socket.c:2699 [inline] __se_sys_sendmsg net/socket.c:2697 [inline] __x64_sys_sendmsg+0x110/0x1a0 net/socket.c:2697 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xed/0x360 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fc6adb66f6d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fc6ac5a6ff8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007fc6addf5fa0 RCX: 00007fc6adb66f6d RDX: 0000000000048084 RSI: 00002000000002c0 RDI: 000000000000000e RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000 ---truncated---Show less

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix locking usage for tcon fields We used to use the cifs_tcp_ses_lock to protect a lot of objects that are not just the server, ses or tcon lists. We later introduced srv_lock, ses_lock and tc_lock to protect fields within the corresponding structs. This was done to provide a more granular protection and avoid unnecessary serialization. There were still a couple of uses of cifs_tcp_ses_lock to provide tcon fields. In this patch, I've replaced them with tc_lock.Show less

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix pci_slot_trylock() error handling Commit a4e772898f8b ("PCI: Add missing bridge lock to pci_bus_lock()") delegates the bridge device's pci_dev_trylock() to pci_bus_trylock() in pci_slot_trylock(), but it forgets to remove the corresponding pci_dev_unlock() when pci_bus_trylock() fails. Before a4e772898f8b, the code did: if (!pci_dev_trylock(dev)) /* <- lock bridge device */ goto unlock; if (dev->subordinate) { if (!pci_bus_trylock(dev->subordinate)) { pci_dev_unlock(dev); /* <- unlock bridge device */ goto unlock; } } After a4e772898f8b the bridge-device lock is no longer taken, but the pci_dev_unlock(dev) on the failure path was left in place, leading to the bug. This yields one of two errors: 1. A warning that the lock is being unlocked when no one holds it. 2. An incorrect unlock of a lock that belongs to another thread. Fix it by removing the now-redundant pci_dev_unlock(dev) on the failure path. [Same patch later posted by Keith at https://patch.msgid.link/20260116184150.3013258-1-kbusch@meta.com]Show less

In the Linux kernel, the following vulnerability has been resolved: Revert "PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV" This reverts commit 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV"), which causes a deadlock by recursively taking pci_rescan_remove_lock when sriov_del_vfs() is called as part of pci_stop_and_remove_bus_device(). For example with the following sequence of commands: $ echo <NUM> > /sys/bus/pci/devices/<pf>/sriov_numvfs $ echo 1 > /sys/bus/pci/devices/<pf>/remove A trimmed trace of the deadlock on a mlx5 device is as below: zsh/5715 is trying to acquire lock: 000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: sriov_disable+0x34/0x140 but task is already holding lock: 000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_stop_and_remove_bus_device_locked+0x24/0x80 ... Call Trace: [<00000259778c4f90>] dump_stack_lvl+0xc0/0x110 [<00000259779c844e>] print_deadlock_bug+0x31e/0x330 [<00000259779c1908>] __lock_acquire+0x16c8/0x32f0 [<00000259779bffac>] lock_acquire+0x14c/0x350 [<00000259789643a6>] __mutex_lock_common+0xe6/0x1520 [<000002597896413c>] mutex_lock_nested+0x3c/0x50 [<00000259784a07e4>] sriov_disable+0x34/0x140 [<00000258f7d6dd80>] mlx5_sriov_disable+0x50/0x80 [mlx5_core] [<00000258f7d5745e>] remove_one+0x5e/0xf0 [mlx5_core] [<00000259784857fc>] pci_device_remove+0x3c/0xa0 [<000002597851012e>] device_release_driver_internal+0x18e/0x280 [<000002597847ae22>] pci_stop_bus_device+0x82/0xa0 [<000002597847afce>] pci_stop_and_remove_bus_device_locked+0x5e/0x80 [<00000259784972c2>] remove_store+0x72/0x90 [<0000025977e6661a>] kernfs_fop_write_iter+0x15a/0x200 [<0000025977d7241c>] vfs_write+0x24c/0x300 [<0000025977d72696>] ksys_write+0x86/0x110 [<000002597895b61c>] __do_syscall+0x14c/0x400 [<000002597896e0ee>] system_call+0x6e/0x90 This alone is not a complete fix as it restores the issue the cited commit tried to solve. A new fix will be provided as a follow on.Show less

In the Linux kernel, the following vulnerability has been resolved: ntfs3: fix circular locking dependency in run_unpack_ex Syzbot reported a circular locking dependency between wnd->rw_lock (sbi->used.bitmap) and ni->file.run_lock. The deadlock scenario: 1. ntfs_extend_mft() takes ni->file.run_lock then wnd->rw_lock. 2. run_unpack_ex() takes wnd->rw_lock then tries to acquire ni->file.run_lock inside ntfs_refresh_zone(). This creates an AB-BA deadlock. Fix this by using down_read_trylock() instead of down_read() when acquiring run_lock in run_unpack_ex(). If the lock is contended, skip ntfs_refresh_zone() - the MFT zone will be refreshed on the next MFT operation. This breaks the circular dependency since we never block waiting for run_lock while holding wnd->rw_lock.Show less

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix TX deadlock when using DMA `dmaengine_terminate_async` does not guarantee that the `__dma_tx_complete` callback will run. The callback is currently the only place where `dma->tx_running` gets cleared. If the transaction is canceled and the callback never runs, then `dma->tx_running` will never get cleared and we will never schedule new TX DMA transactions again. This change makes it so we clear `dma->tx_running` after we terminate the DMA transaction. This is "safe" because `serial8250_tx_dma_flush` is holding the UART port lock. The first thing the callback does is also grab the UART port lock, so access to `dma->tx_running` is serialized.Show less

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix soft lockup in mptcp_recvmsg() syzbot reported a soft lockup in mptcp_recvmsg() [0]. When receiving data with MSG_PEEK | MSG_WAITALL flags, the skb is not removed from the sk_receive_queue. This causes sk_wait_data() to always find available data and never perform actual waiting, leading to a soft lockup. Fix this by adding a 'last' parameter to track the last peeked skb. This allows sk_wait_data() to make informed waiting decisions and prevent infinite loops when MSG_PEEK is used. [0]: watchdog: BUG: soft lockup - CPU#2 stuck for 156s! [server:1963] Modules linked in: CPU: 2 UID: 0 PID: 1963 Comm: server Not tainted 6.19.0-rc8 #61 PREEMPT(none) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:sk_wait_data+0x15/0x190 Code: 80 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 41 56 41 55 41 54 49 89 f4 55 48 89 d5 53 48 89 fb <48> 83 ec 30 65 48 8b 05 17 a4 6b 01 48 89 44 24 28 31 c0 65 48 8b RSP: 0018:ffffc90000603ca0 EFLAGS: 00000246 RAX: 0000000000000000 RBX: ffff888102bf0800 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffffc90000603d18 RDI: ffff888102bf0800 RBP: 0000000000000000 R08: 0000000000000002 R09: 0000000000000101 R10: 0000000000000000 R11: 0000000000000075 R12: ffffc90000603d18 R13: ffff888102bf0800 R14: ffff888102bf0800 R15: 0000000000000000 FS: 00007f6e38b8c4c0(0000) GS:ffff8881b877e000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055aa7bff1680 CR3: 0000000105cbe000 CR4: 00000000000006f0 Call Trace: <TASK> mptcp_recvmsg+0x547/0x8c0 net/mptcp/protocol.c:2329 inet_recvmsg+0x11f/0x130 net/ipv4/af_inet.c:891 sock_recvmsg+0x94/0xc0 net/socket.c:1100 __sys_recvfrom+0xb2/0x130 net/socket.c:2256 __x64_sys_recvfrom+0x1f/0x30 net/socket.c:2267 do_syscall_64+0x59/0x2d0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e arch/x86/entry/entry_64.S:131 RIP: 0033:0x7f6e386a4a1d Code: 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8d 05 f1 de 2c 00 41 89 ca 8b 00 85 c0 75 20 45 31 c9 45 31 c0 b8 2d 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 6b f3 c3 66 0f 1f 84 00 00 00 00 00 41 56 41 RSP: 002b:00007ffc3c4bb078 EFLAGS: 00000246 ORIG_RAX: 000000000000002d RAX: ffffffffffffffda RBX: 000000000000861e RCX: 00007f6e386a4a1d RDX: 00000000000003ff RSI: 00007ffc3c4bb150 RDI: 0000000000000004 RBP: 00007ffc3c4bb570 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000103 R11: 0000000000000246 R12: 00005605dbc00be0 R13: 00007ffc3c4bb650 R14: 0000000000000000 R15: 0000000000000000 </TASK>Show less