NULL Pointer Dereference

In the Linux kernel, the following vulnerability has been resolved: nexthop: fix IPv6 route referencing IPv4 nexthop syzbot reported a panic [1] [2]. When an IPv6 nexthop is replaced with an IPv4 nexthop, the has_v4 flag of all groups containing this nexthop is not updated. This is because nh_group_v4_update is only called when replacing AF_INET to AF_INET6, but the reverse direction (AF_INET6 to AF_INET) is missed. This allows a stale has_v4=false to bypass fib6_check_nexthop, causing IPv6 routes to be attached to groups that effectively contain only AF_INET members. Subsequent route lookups then call nexthop_fib6_nh() which returns NULL for the AF_INET member, leading to a NULL pointer dereference. Fix by calling nh_group_v4_update whenever the family changes, not just AF_INET to AF_INET6. Reproducer: # AF_INET6 blackhole ip -6 nexthop add id 1 blackhole # group with has_v4=false ip nexthop add id 100 group 1 # replace with AF_INET (no -6), has_v4 stays false ip nexthop replace id 1 blackhole # pass stale has_v4 check ip -6 route add 2001:db8::/64 nhid 100 # panic ping -6 2001:db8::1 [1] https://syzkaller.appspot.com/bug?id=e17283eb2f8dcf3dd9b47fe6f67a95f71faadad0 [2] https://syzkaller.appspot.com/bug?id=8699b6ae54c9f35837d925686208402949e12ef3Show less

In the Linux kernel, the following vulnerability has been resolved: ice: fix potential NULL pointer deref in error path of ice_set_ringparam() ice_set_ringparam nullifies tstamp_ring of temporary tx_rings, without clearing ICE_TX_RING_FLAGS_TXTIME bit. When ICE_TX_RING_FLAGS_TXTIME is set and the subsequent ice_setup_tx_ring() call fails, a NULL pointer dereference could happen in the unwinding sequence: ice_clean_tx_ring() -> ice_is_txtime_cfg() == true (ICE_TX_RING_FLAGS_TXTIME is set) -> ice_free_tx_tstamp_ring() -> ice_free_tstamp_ring() -> tstamp_ring->desc (NULL deref) Clear ICE_TX_RING_FLAGS_TXTIME bit to avoid the potential issue. Note that this potential issue is found by manual code review. Compile test only since unfortunately I don't have E830 devices.Show less

In the Linux kernel, the following vulnerability has been resolved: netfilter: nfnetlink_osf: fix potential NULL dereference in ttl check The nf_osf_ttl() function accessed skb->dev to perform a local interface address lookup without verifying that the device pointer was valid. Additionally, the implementation utilized an in_dev_for_each_ifa_rcu loop to match the packet source address against local interface addresses. It assumed that packets from the same subnet should not see a decrement on the initial TTL. A packet might appear it is from the same subnet but it actually isn't especially in modern environments with containers and virtual switching. Remove the device dereference and interface loop. Replace the logic with a switch statement that evaluates the TTL according to the ttl_check.Show less

In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_dualpi2: drain both C-queue and L-queue in dualpi2_change() Fix dualpi2_change() to correctly enforce updated limit and memlimit values after a configuration change of the dualpi2 qdisc. Before this patch, dualpi2_change() always attempted to dequeue packets via the root qdisc (C-queue) when reducing backlog or memory usage, and unconditionally assumed that a valid skb will be returned. When traffic classification results in packets being queued in the L-queue while the C-queue is empty, this leads to a NULL skb dereference during limit or memlimit enforcement. This is fixed by first dequeuing from the C-queue path if it is non-empty. Once the C-queue is empty, packets are dequeued directly from the L-queue. Return values from qdisc_dequeue_internal() are checked for both queues. When dequeuing from the L-queue, the parent qdisc qlen and backlog counters are updated explicitly to keep overall qdisc statistics consistent.Show less

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_sip: don't use simple_strtoul Replace unsafe port parsing in epaddr_len(), ct_sip_parse_header_uri(), and ct_sip_parse_request() with a new sip_parse_port() helper that validates each digit against the buffer limit, eliminating the use of simple_strtoul() which assumes NUL-terminated strings. The previous code dereferenced pointers without bounds checks after sip_parse_addr() and relied on simple_strtoul() on non-NUL-terminated skb data. A port that reaches the buffer limit without a trailing character is also rejected as malformed. Also get rid of all simple_strtoul() usage in conntrack, prefer a stricter version instead. There are intentional changes: - Bail out if number is > UINT_MAX and indicate a failure, same for too long sequences. While we do accept 05535 as port 5535, we will not accept e.g. 'sip:10.0.0.1:005060'. While its syntactically valid under RFC 3261, we should restrict this to not waste cycles when presented with malformed packets with 64k '0' characters. - Force base 10 in ct_sip_parse_numerical_param(). This is used to fetch 'expire=' and 'rports='; both are expected to use base-10. - In nf_nat_sip.c, only accept the parsed value if its within the 1k-64k range. - epaddr_len now returns 0 if the port is invalid, as it already does for invalid ip addresses. This is intentional. nf_conntrack_sip performs lots of guesswork to find the right parts of the message to parse. Being stricter could break existing setups. Connection tracking helpers are designed to allow traffic to pass, not to block it. Based on an earlier patch from Jenny Guanni Qu <qguanni@gmail.com>.Show less

In the Linux kernel, the following vulnerability has been resolved: sched/fair: Clear rel_deadline when initializing forked entities A yield-triggered crash can happen when a newly forked sched_entity enters the fair class with se->rel_deadline unexpectedly set. The failing sequence is: 1. A task is forked while se->rel_deadline is still set. 2. __sched_fork() initializes vruntime, vlag and other sched_entity state, but does not clear rel_deadline. 3. On the first enqueue, enqueue_entity() calls place_entity(). 4. Because se->rel_deadline is set, place_entity() treats se->deadline as a relative deadline and converts it to an absolute deadline by adding the current vruntime. 5. However, the forked entity's deadline is not a valid inherited relative deadline for this new scheduling instance, so the conversion produces an abnormally large deadline. 6. If the task later calls sched_yield(), yield_task_fair() advances se->vruntime to se->deadline. 7. The inflated vruntime is then used by the following enqueue path, where the vruntime-derived key can overflow when multiplied by the entity weight. 8. This corrupts cfs_rq->sum_w_vruntime, breaks EEVDF eligibility calculation, and can eventually make all entities appear ineligible. pick_next_entity() may then return NULL unexpectedly, leading to a later NULL dereference. A captured trace shows the effect clearly. Before yield, the entity's vruntime was around: 9834017729983308 After yield_task_fair() executed: se->vruntime = se->deadline the vruntime jumped to: 19668035460670230 and the deadline was later advanced further to: 19668035463470230 This shows that the deadline had already become abnormally large before yield_task_fair() copied it into vruntime. rel_deadline is only meaningful when se->deadline really carries a relative deadline that still needs to be placed against vruntime. A freshly forked sched_entity should not inherit or retain this state. Clear se->rel_deadline in __sched_fork(), together with the other sched_entity runtime state, so that the first enqueue does not interpret the new entity's deadline as a stale relative deadline.Show less

In the Linux kernel, the following vulnerability has been resolved: libceph: Fix potential null-ptr-deref in decode_choose_args() A message of type CEPH_MSG_OSD_MAP contains an OSD map that itself contains a CRUSH map. When decoding this CRUSH map in crush_decode(), an array of max_buckets CRUSH buckets is decoded, where some indices may not refer to actual buckets and are therefore set to NULL. The received CRUSH map may optionally contain choose_args that get decoded in decode_choose_args(). When decoding a crush_choose_arg_map, a series of choose_args for different buckets is decoded, with the bucket_index being read from the incoming message. It is only checked that the bucket index does not exceed max_buckets, but not that it doesn't point to an index with a NULL bucket. If a (potentially corrupted) message contains a crush_choose_arg_map including such a bucket_index, a null pointer dereference may occur in the subsequent processing when attempting to access the bucket with the given index. This patch fixes the issue by extending the affected check. Now, it is only attempted to access the bucket if it is not NULL.Show less

In the Linux kernel, the following vulnerability has been resolved: drm/xe/dma-buf: handle empty bo and UAF races There look to be some nasty races here when triggering the invalidate_mappings hook: 1) We do xe_bo_alloc() followed by the attach, before the actual full bo init step in xe_dma_buf_init_obj(). However the bo is visible on the attachments list after the attach. This is bad since exporter driver, say amdgpu, can at any time call back into our invalidate_mappings hook, with an empty/bogus bo, leading to potential bugs/crashes. 2) Similar to 1) but here we get a UAF, when the invalidate_mappings hook is triggered. For example, we get as far as xe_bo_init_locked() but this fails in some way. But here the bo will be freed on error, but we still have it attached from dma-buf pov, so if the invalidate_mappings is now triggered then the bo we access is gone and we trigger UAF and more bugs/crashes. To fix this, move the attach step until after we actually have a fully set up buffer object. Note that the bo is not published to userspace until later, so not sure what the comment "Don't publish the bo until we have a valid attachment", is referring to. We have at least two different customers reporting hitting a NULL ptr deref in evict_flags when importing something from amdgpu, followed by triggering the evict flow. Hit rate is also pretty low, which would hint at some kind of race, so something like 1) or 2) might explain this. v2: - Shuffle the order of the ops slightly (no functional change) - Improve the comment to better explain the ordering (Matt B) (cherry picked from commit af1f2ad0c59fe4e2f924c526f66e968289d77971)Show less

In the Linux kernel, the following vulnerability has been resolved: net/smc: avoid NULL deref of conn->lnk in smc_msg_event tracepoint The smc_msg_event tracepoint class, shared by smc_tx_sendmsg and smc_rx_recvmsg, unconditionally dereferences smc->conn.lnk: __string(name, smc->conn.lnk->ibname) conn->lnk is only set for SMC-R; for SMC-D it is NULL. Other code on these paths already handles this (e.g. !conn->lnk in SMC_STAT_RMB_TX_SIZE_SMALL()). With the tracepoint enabled, the first sendmsg()/recvmsg() on an SMC-D socket crashes: Oops: general protection fault, probably for non-canonical address KASAN: null-ptr-deref in range [...] RIP: 0010:strlen+0x1e/0xa0 Call Trace: trace_event_raw_event_smc_msg_event (net/smc/smc_tracepoint.h:44) smc_rx_recvmsg (net/smc/smc_rx.c:515) smc_recvmsg (net/smc/af_smc.c:2859) __sys_recvfrom (net/socket.c:2315) __x64_sys_recvfrom (net/socket.c:2326) do_syscall_64 The faulting address 0x3e0 is offsetof(struct smc_link, ibname), confirming the NULL ->lnk deref. Enabling the tracepoint requires root, but the trigger itself is unprivileged: socket(AF_SMC, ...) has no capability check, and SMC-D negotiation needs no admin step on s390 or on x86 with the loopback ISM device loaded. Log an empty device name for SMC-D instead of dereferencing NULL.Show less

In the Linux kernel, the following vulnerability has been resolved: net/rds: fix NULL deref in rds_ib_send_cqe_handler() on masked atomic completion rds_ib_xmit_atomic() always programs a masked atomic opcode (IB_WR_MASKED_ATOMIC_CMP_AND_SWP or IB_WR_MASKED_ATOMIC_FETCH_AND_ADD) for every RDS atomic cmsg. But the completion-side switch in rds_ib_send_unmap_op() only handles the non-masked opcodes, so a masked atomic completion falls through to default and returns rm == NULL while send->s_op is left set. rds_ib_send_cqe_handler() then dereferences the NULL rm via rm->m_final_op, oopsing in softirq context. An unprivileged AF_RDS sendmsg() of an atomic cmsg over an active RDS/IB connection triggers it; on hardware that natively accepts masked atomics (mlx4, mlx5) no extra setup is needed. RDS/IB: rds_ib_send_unmap_op: unexpected opcode 0xd in WR! Oops: general protection fault [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000190-0x0000000000000197] RIP: rds_ib_send_cqe_handler+0x25c/0xb10 (net/rds/ib_send.c:282) Call Trace: <IRQ> rds_ib_send_cqe_handler (net/rds/ib_send.c:282) poll_scq (net/rds/ib_cm.c:274) rds_ib_tasklet_fn_send (net/rds/ib_cm.c:294) tasklet_action_common (kernel/softirq.c:943) handle_softirqs (kernel/softirq.c:573) run_ksoftirqd (kernel/softirq.c:479) </IRQ> Kernel panic - not syncing: Fatal exception in interrupt Handle the masked atomic opcodes in the same case as the non-masked ones: they map to the same struct rds_message.atomic union member, so the existing container_of()/rds_ib_send_unmap_atomic() body is correct for them.Show less

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix NULL pointer dereference in bpf_sk_storage_clone and diag paths bpf_selem_unlink_nofail() sets SDATA(selem)->smap to NULL before removing the selem from the storage hlist. A concurrent RCU reader in bpf_sk_storage_clone() can observe the selem still on the list with smap already NULL, causing a NULL pointer dereference. general protection fault, probably for non-canonical address 0xdffffc000000000a: KASAN: null-ptr-deref in range [0x0000000000000050-0x0000000000000057] RIP: 0010:bpf_sk_storage_clone+0x1cd/0xaa0 net/core/bpf_sk_storage.c:174 Call Trace: <IRQ> sk_clone+0xfed/0x1980 net/core/sock.c:2591 inet_csk_clone_lock+0x30/0x760 net/ipv4/inet_connection_sock.c:1222 tcp_create_openreq_child+0x35/0x2680 net/ipv4/tcp_minisocks.c:571 tcp_v4_syn_recv_sock+0x123/0xf90 net/ipv4/tcp_ipv4.c:1729 tcp_check_req+0x8e1/0x2580 include/net/tcp.h:855 tcp_v4_rcv+0x1845/0x3b80 net/ipv4/tcp_ipv4.c:2347 Add a NULL check for smap in bpf_sk_storage_clone(). bpf_sk_storage_diag_put_all() has the same issue. Add a NULL check and pass the validated smap directly to diag_get(), which is refactored to take smap as a parameter instead of reading it internally. bpf_sk_storage_diag_put() uses diag->maps[i] which is always valid under its refcount, so diag->maps[i] is passed directly to diag_get().Show less

In the Linux kernel, the following vulnerability has been resolved: sctp: stream: fully roll back denied add-stream state When ADD_OUT_STREAMS is denied, SCTP only shrinks the queued chunks and then lowers outcnt. That leaves removed stream metadata behind, so a later re-add can reuse a stale ext and hit a null-pointer dereference in the scheduler get path. Fix the rollback by tearing down the removed stream state the same way other stream resizes do. Unschedule the current scheduler state, drop the removed stream ext state with sctp_stream_outq_migrate(), and then reschedule the remaining streams. This keeps scheduler-private RR/FC/PRIO lists consistent while fully rolling back denied outgoing stream additions.Show less

In the Linux kernel, the following vulnerability has been resolved: vrf: Fix a potential NPD when removing a port from a VRF RCU readers that identified a net device as a VRF port using netif_is_l3_slave() assume that a subsequent call to netdev_master_upper_dev_get_rcu() will return a VRF device. They then continue to dereference its l3mdev operations. This assumption is not always correct and can result in a NPD [1]. There is no RCU synchronization when removing a port from a VRF, so it is possible for an RCU reader to see a new master device (e.g., a bridge) that does not have l3mdev operations. Fix by adding RCU synchronization after clearing the IFF_L3MDEV_SLAVE flag. Skip this synchronization when a net device is removed from a VRF as part of its deletion and when the VRF device itself is deleted. In the latter case an RCU grace period will pass by the time RTNL is released. [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] RIP: 0010:l3mdev_fib_table_rcu (net/l3mdev/l3mdev.c:181) [...] Call Trace: <TASK> l3mdev_fib_table_by_index (net/l3mdev/l3mdev.c:201 net/l3mdev/l3mdev.c:189) __inet_bind (net/ipv4/af_inet.c:499 (discriminator 3)) inet_bind_sk (net/ipv4/af_inet.c:469) __sys_bind (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:1951 (discriminator 1)) __x64_sys_bind (net/socket.c:1969 (discriminator 1) net/socket.c:1967 (discriminator 1) net/socket.c:1967 (discriminator 1)) do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)Show less

In the Linux kernel, the following vulnerability has been resolved: batman-adv: dat: handle forward allocation error batadv_dat_forward_data() calls pskb_copy_for_clone() to duplicate an skb for each DHT candidate, but does not check the return value before passing it to batadv_send_skb_prepare_unicast_4addr(). That function dereferences the skb unconditionally, so a failed allocation triggers a NULL pointer dereference. Skip forwarding to the current DHT candidate on allocation failure.Show less

In the Linux kernel, the following vulnerability has been resolved: batman-adv: v: stop OGMv2 on disabled interface When a batadv_hard_iface is disabled, its mesh_iface pointer is set to NULL. However, batadv_v_ogm_send_meshif() may still dispatch OGMs via batadv_v_ogm_queue_on_if() for interfaces that have since lost their mesh_iface association. This results in a NULL pointer dereference when batadv_v_ogm_queue_on_if() unconditionally calls netdev_priv() on the now NULL hard_iface->mesh_iface to retrieve the batadv_priv. It is necessary to ensure that the batadv_v_ogm_queue_on_if() checks that it is using the same mesh_iface for which batadv_v_ogm_send_meshif() was called.Show less

GPAC MP4Box v2.4 was discovered to contain a NULL pointer dereference in the gf_isom_add_track_kind() function at isomedia/isom_write.c. This vulnerability allows attackers to cause a Denial of Service (DoS) via a crafted MP4 file.Show less

There is a NULL pointer dereference vulnerability in NI grpc-device in the data moniker service that may allow an attacker to cause a denial of service by triggering a crash.  Successful exploitation requires an attacker to provide an unknown value to the data moniker service. This affects NI grpc-device 2.17.0 and prior versions.Show less

pam_usb provides hardware authentication for Linux using ordinary removable media. In versions 0.9.1 and below, pusb_is_loginctl_local() can cause a NULL dereference crash when parsing loginctl output. The function calls popen() and reads the result; if the Remote field is only a newline, fgets() succeeds but strtok_r(buf, "\n", &saveptr) returns NULL. A subsequent strcmp(is_remote, "no") then dereferences NULL, causing undefined behavior (typically SIGSEGV) and crashing the PAM module. This can crash the authenticating process (e.g., sudo, login) and, depending on PAM stack configuration, deny access for all users of the affected service. This issue has been fixed in version 0.9.2.Show less

HAProxy through 3.4.0, fixed in commit 9a6d1fe, contains a null pointer dereference vulnerability in hpack_dht_insert() within src/hpack-tbl.c that fails to validate the return value of hpack_dht_defrag() when the memory pool is exhausted. An attacker can trigger HPACK dynamic table insertions under memory pressure to dereference a NULL pointer and crash HAProxy worker processes, causing denial of service.Show less