Improper Access Control

A vulnerability has been identified in PCS neo (Administration Console) (All versions < V3.1), TIA Portal (V15, V15.1 and V16). Manipulating certain files in specific folders could allow a local attacker to execute code with SYSTEM privileges. The security vulnerability could be exploited by an attacker with a valid account and limited access rights on the system.Show less

A flaw was found in the default configuration of dnsmasq, as shipped with Fedora versions prior to 31 and in all versions Red Hat Enterprise Linux, where it listens on any interface and accepts queries from addresses outside of its local subnet. In particular, the option `local-service` is not enabled. Running dnsmasq in this manner may inadvertently make it an open resolver accessible from any address on the internet. This flaw allows an attacker to conduct a Distributed Denial of Service (DDoS) against other systems.Show less

A vulnerability in the IPv6 traffic processing of Cisco IOS XR Software and Cisco NX-OS Software for certain Cisco devices could allow an unauthenticated, remote attacker to bypass an IPv6 access control list (ACL) that is configured for an interface of an affected device. The vulnerability is due to improper processing of IPv6 traffic that is sent through an affected device. An attacker could exploit this vulnerability by sending crafted IPv6 packets that traverse the affected device. A successful exploit could allow the attacker to access resources that would typically be protected by the interface ACL.Show less

A vulnerability in the Local Packet Transport Services (LPTS) programming of the SNMP with the management plane protection feature of Cisco IOS XR Software could allow an unauthenticated, remote attacker to allow connections despite the management plane protection that is configured to deny access to the SNMP server of an affected device. This vulnerability is due to incorrect LPTS programming when using SNMP with management plane protection. An attacker could exploit this vulnerability by connecting to an affected device using SNMP. A successful exploit could allow the attacker to connect to the device on the configured SNMP ports. Valid credentials are required to execute any of the SNMP requests.Show less

This vulnerability allows network-adjacent attackers to disclose sensitive information on affected installations of NETGEAR R7450 1.2.0.62_1.0.1 routers. Authentication is not required to exploit this vulnerability. The specific flaw exists within the SOAP API endpoint, which listens on TCP port 80 by default. The issue results from the lack of proper access control. An attacker can leverage this vulnerability to disclose stored credentials, leading to further compromise. Was ZDI-CAN-11559.Show less

The vulnerability have been reported to affect earlier versions of QTS. If exploited, this improper access control vulnerability could allow attackers to compromise the security of the software by gaining privileges, or reading sensitive information. This issue affects: QNAP Systems Inc. Helpdesk versions prior to 3.0.3.Show less

An issue was discovered on TK-Star Q90 Junior GPS horloge 3.1042.9.8656 devices. Any SIM card used with the device cannot have a PIN configured. If a PIN is configured, the device simply produces a "Remove PIN and restart!" message, and cannot be used. This makes it easier for an attacker to use the SIM card by stealing the device.Show less

An issue was discovered on TK-Star Q90 Junior GPS horloge 3.1042.9.8656 devices. It performs actions based on certain SMS commands. This can be used to set up a voice communication channel from the watch to any telephone number, initiated by sending a specific SMS and using the default password, e.g., pw,<password>,call,<mobile_number> triggers an outbound call from the watch. The password is sometimes available because of CVE-2019-20471.Show less

While investigating ARTEMIS-2964 it was found that the creation of advisory messages in the OpenWire protocol head of Apache ActiveMQ Artemis 2.15.0 bypassed policy based access control for the entire session. Production of advisory messages was not subject to access control in error.Show less

When the "Intrusion Detection Service" (IDS) feature is configured on Juniper Networks MX series with a dynamic firewall filter using IPv6 source or destination prefix, it may incorrectly match the prefix as /32, causing the filter to block unexpected traffic. This issue affects only IPv6 prefixes when used as source and destination. This issue affects MX Series devices using MS-MPC, MS-MIC or MS-SPC3 service cards with IDS service configured. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S10 on MX Series; 17.4 versions prior to 17.4R3-S3 on MX Series; 18.1 versions prior to 18.1R3-S11 on MX Series; 18.2 versions prior to 18.2R3-S6 on MX Series; 18.3 versions prior to 18.3R3-S4 on MX Series; 18.4 versions prior to 18.4R3-S6 on MX Series; 19.1 versions prior to 19.1R2-S2, 19.1R3-S3 on MX Series; 19.2 versions prior to 19.2R3-S1 on MX Series; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1 on MX Series; 19.4 versions prior to 19.4R3 on MX Series; 20.1 versions prior to 20.1R2 on MX Series; 20.2 versions prior to 20.2R2 on MX Series;Show less

Citrix Secure Mail for Android before 20.11.0 suffers from improper access control allowing unauthenticated access to read limited calendar related data stored within Secure Mail. Note that a malicious app would need to be installed on the Android device or a threat actor would need to execute arbitrary code on the Android device.Show less

A vulnerability has been reported to affect earlier QNAP devices running QTS 4.3.4 to 4.3.6. Caused by improper limitations of a pathname to a restricted directory, this vulnerability allows for renaming arbitrary files on the target system, if exploited. QNAP have already fixed this vulnerability in the following versions: QTS 4.3.6.0895 build 20190328 (and later) QTS 4.3.4.0899 build 20190322 (and later) This issue does not affect QTS 4.4.x or QTS 4.5.x.Show less

Improper access control in Odoo Community 13.0 and earlier and Odoo Enterprise 13.0 and earlier, allows remote authenticated users to modify translated terms, which may lead to arbitrary content modification on translatable elements.Show less

Improper access control in mail module (followers) in Odoo Community 13.0 and earlier and Odoo Enterprise 13.0 and earlier, allows remote authenticated users to obtain access to messages posted on business records there were not given access to, and subscribe to receive future messages.Show less

Improper access control in mail module (notifications) in Odoo Community 14.0 and earlier and Odoo Enterprise 14.0 and earlier, allows remote authenticated users to obtain access to arbitrary messages in conversations they were not a party to.Show less

Improper access control in Odoo Community 14.0 and earlier and Odoo Enterprise 14.0 and earlier, allows remote authenticated users with access to contact management to modify user accounts, leading to privilege escalation.Show less

Improper access control in message routing in Odoo Community 12.0 and earlier and Odoo Enterprise 12.0 and earlier allows remote authenticated users to create arbitrary records via crafted payloads, which may allow privilege escalation.Show less