Improper Validation of Array Index

In the Linux kernel, the following vulnerability has been resolved: Input: mms114 - fix touch indexing for MMS134S and MMS136 The MMS134S and MMS136 touch controllers have an event size of 6 bytes rather than 8 bytes. When __mms114_read_reg() reads the touch data packet from the device into the touch buffer, the events are packed tightly at 6-byte intervals. However, the driver iterates through the events using standard C array indexing (touch[index]), where each element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any touch events beyond the first one are read from incorrect offsets and parsed improperly. Fix this by explicitly calculating the byte offset for each touch event based on the device's specific event size.Show less

In the Linux kernel, the following vulnerability has been resolved: Input: touchwin - reset the packet index on every complete packet tw_interrupt() accumulates each non-zero serial byte into a fixed three-byte buffer with a running index that is only reset once a full packet has been received *and* the device's two Y bytes agree: tw->data[tw->idx++] = data; if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) { ... tw->idx = 0; } The reset is gated on tw->data[1] == tw->data[2], a value the device controls. A malicious, malfunctioning or counterfeit Touchwindow peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the index reaches TW_LENGTH without the equality holding, is never reset, and keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte array and the rest of the heap-allocated struct tw, one attacker-chosen byte at a time -- an unbounded, device-driven heap out-of-bounds write. Reset the index on every completed packet and report an event only when the two Y bytes match, like the other serio touchscreen drivers do.Show less

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: simple-mux: Fix enum control bounds check simple_mux_control_put() rejects values greater than e->items, but enum control values are zero based. For the two-entry mux used by this driver, valid values are 0 and 1, so value 2 must be rejected as well. Accepting e->items can store an invalid mux state, pass it to the GPIO setter, and pass it on to the DAPM mux update path where it is used as an index into the enum text array. Use the same >= e->items check used by the ASoC enum helpers.Show less

In the Linux kernel, the following vulnerability has been resolved: octeontx2-af: CGX: add bounds check to cgx_speed_mbps index cgx_speed_mbps has 13 elements but RESP_LINKSTAT_SPEED can yield values 0-15. If it returns a value >= 13, this causes an out-of-bounds array access. Add a bounds check and default to speed 0 if the index is out of range.Show less

In the Linux kernel, the following vulnerability has been resolved: iio: light: veml6075: add bounds check to veml6075_it_ms index veml6075_it_ms has 5 elements but VEML6075_CONF_IT can yield values 0-7. If it returns a value >= 5, this causes an out-of-bounds array access. Add a bounds check and return -EINVAL if the index is out of range. The problem values are reserved so should never be read from the register. Hence this is hardening against fault device, missprogramming or bus corruption.Show less

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads1298: add bounds check to pga_settings index ads1298_pga_settings has 7 elements but ADS1298_MASK_CH_PGA can yield values 0-7. If it yields a value >= 7, this causes an out-of-bounds array access. Add a bounds check and return -EINVAL if the index is out of range. Note that the remaining value b111 is reserved so should not be seen in a correctly functioning system.Show less

Wire provides gRPC and protocol buffers for Android, Kotlin, Swift, and Java. Prior to 6.3.0 and 7.0.0-alpha03, ByteArrayProtoReader32.skipGroup() and ProtoReader.skipGroup() in wire-runtime do not validate that a LENGTH_DELIMITED field length is non-negative before skip(), allowing a crafted protobuf varint encoding -128 as a signed Int to make skip(-128) move the internal position negative and make the next readByte() throw ArrayIndexOutOfBoundsException instead of the documented IOException or ProtocolException, which can crash services using ProtoAdapter.decode(byte[]) on untrusted payloads. This issue is fixed in versions 6.3.0 and 7.0.0-alpha03.Show less

Helm through 4.2.3, fixed in commit ba6c9a2, contains a denial of service vulnerability in the Files.Lines template helper in pkg/engine/files.go that allows attackers to trigger an index out of range panic by including zero-length byte slices in chart files. Attackers can include empty files in Helm charts to cause deterministic render failures across template, install, upgrade, lint, and SDK Engine.Render operations.Show less

Dasel is a command-line tool and library for querying, modifying, and transforming data structures. From 3.0.0 until 3.10.1, the escape sequence handler in (*Tokenizer).parseCurRune in selector/lexer/tokenize.go increments past a trailing backslash in a quoted string such as "\ or '\ and then reads p.src[pos] without a bounds check, allowing attacker-controlled selector strings to trigger a Go index-out-of-range panic. This issue is fixed in version 3.10.1.Show less

ncnn is a high-performance neural network inference framework optimized for the mobile platform. In commit e54f7b1f88434e1d844ea0551b880a1cfb079ce1 and earlier, ncnn allows an out-of-bounds heap write in ncnn::ParamDict::load_param() when Net::load_param() loads a malicious .param model file because the parsed parameter id is checked only against id >= NCNN_MAX_PARAM_COUNT, allowing a negative id to index before the params[NCNN_MAX_PARAM_COUNT] array. This vulnerability is fixed by commit 5a0288f255daa6c3294f77109f67718e434ec020.Show less

Ollama downloadBlob Improper Validation of Array Index Denial-of-Service Vulnerability. This vulnerability allows remote attackers to create a denial-of-service condition on affected installations of Ollama. Authentication is not required to exploit this vulnerability. The specific flaw exists within the downloadBlob function. The issue results from the lack of proper validation of user-supplied data, which can result in a memory access past the end of an allocated array. An attacker can leverage this vulnerability to create a denial-of-service condition on the system. Was ZDI-CAN-27277.Show less

The application opens a PDF, but the cloud-like appearance of the construction process lacks proper setting of an upper limit and consistency checks. Out-of-bounds access to the underlying array is exposed, ultimately leading to a crash of the application.Show less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. #### byPass command index-out-of-boundShow less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. #### pause command index-out-of-boundShow less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. #### play command index-out-of-boundShow less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. #### disconnect command index-out-of-boundShow less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. ### saveVideo command index-out-of-bound When sending the `saveVideo` command, the `index` field is extracted from the websocket message [1]. Then without checking the range of the index, it is used to trigger a CriticalSection ([2]) and releases it [3]. The release function call ([3]) is executed using a function pointer which will be read out of bounds potentially leading to code execution: v6 = get_entry(a2, "index"); result = json_is_value_int(v6); if ( (_BYTE)result ) { v8 = get_entry(a2, "index"); index = json_value_to_int(&v8->value); // [1] result = CCriticalSection::EnterCritSection(&this->crit_sections[index]); //[2] if ( result ) { if ( this->array_of_IPCams[index] ) { if ( this->array_of_IPCams[index]->field_20 ) do_PostMessageA((CViewer *)this->array_of_IPCams[index], 0x111u, 0x139Fu, v11); } return (*(int (__thiscall **)(CCriticalSection *))(this->crit_sections[index].vtbl + 20))(&this->crit_sections[index]); //[3] } }Show less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. #### snapshot command index-out-of-boundShow less

GeoWebPlayer (also called "Web Plugin" in the GV-VMS documentation and "WS Player" for VMS-Cloud) is an addon that can be installed with various GeoVision software (GV-VMS, GV-Cloud, ...). It creates a websocket server that expands the capabilities of the various web-interfaces provided by the GeoVision software and may be necessary for them to function properly. The Websocket server can accept various commands coming from localhost. Many of the commands will take an `index` value that is then used to access various arrays to enter critical sections, perform various actions via function calls, etc. However the `index` value is usually not checked for valid range, and as such it can be used to access multiple arrays out-of-bound. #### 2wayAudio command index-out-of-boundShow less